I know I just realized what all was wrong and missing. Any suggestions about the bypass solenoid electrical plug in? I don't have that.Originally Posted by DanPrixGTP
|
|
11-26-2012
I know I just realized what all was wrong and missing. Any suggestions about the bypass solenoid electrical plug in? I don't have that.
http://www.streetfire.net/video/2001...ynp_208097.htm
11-26-2012
No the vacuum will control the BBV
http://www.streetfire.net/video/2001...ynp_208097.htm
11-26-2012
the solenoid is there for abuse mode, you dont need it
http://www.streetfire.net/video/2001...ynp_208097.htm
11-26-2012
So do I still need to connect the hoses to it?
11-26-2012
no, just to the BBV
http://www.streetfire.net/video/2001...ynp_208097.htm
11-26-2012
So I need a T coming off the fuel press, one line going to the LIM and another line bypassing the bypass solenoid and going into the bottom of the BBV? Correct??
11-26-2012
the BBV should be hooked up to the top of the blower, to the one you have capped now. Watch my Video I posted it shows the BBV hook up. Under the blower snout you should have only the MAP and the Regulator running off of that.
http://www.streetfire.net/video/2001...ynp_208097.htm
11-26-2012
Do you have anything connected to the bottom end of the BBV? Couldn't tell in the video.
How much boost are you running? what size pulley?
11-26-2012
im running a 3.2 pulley 10psi or so. no just the vac line to the top of the BBV the other nipple needs to vent
http://www.streetfire.net/video/2001...ynp_208097.htm
11-26-2012
I did a T on the regulator. One line going under the blower as well as the map sensor. Other side of the T is going to the throttle body. Then connected the BBV to the top that was plugged. Still only have a max of 2.9lbs of boost. I'm scanning with an aeroforce. What else could it be? bad BBV??
11-26-2012
the line off the TB goes to the evap on the back of the engine. not the fuel rail.
i'd post a pic, but i cant seem to get it done right now, as the sites being picky right now.
post # 4 has the pic of the vac line off the Tb it goes to the back to the evap. http://www.grandprixforums.net/vacuu...ber-70863.html
it also shows the vac line you have blocked off, where that hose goes to, the by pass actuator.
11-26-2012
and you'll want to set it up with this routing.
Attachment 10192
top of the sc tree to the by pass actuator to by pass solenoid then to fuel pressure regulator, then the T under the snout, then to the map sensor.
Tb line goes to the evap on the back as shown.
11-26-2012
Where is the evap??
11-26-2012
your attachment didnt work
11-26-2012
post 48 in this thread page 3 also has a pic of the line from the under the snout, to the fuel pressure reg, to the by pass solenoid.
11-26-2012
follow the vac routing for a 98 and up diagram on page 3, evap is right by the map sensor on the back of the sc.
sites not being pic friendly right now.
11-26-2012
Am I looking for the evap canister purge SOL?? is that the one your talking about?
11-26-2012
yes sir. that one goes to the Tb and another line that that went off to the drivers side of the car to the canister. so a in and out on the evap.
11-26-2012
Heres my map sensor and Evap Canister. both in the front
| « Previous Thread | Next Thread » |
| Tags for this Thread |
| Bookmarks |
Bookmarks |
