What did you do to your Car today?

Rockers are done, it seems to pull a bit harder, there was some noise from the rear but it seems to have fixed itself. Probably just needed to oil up a bit. We'll see. Pulls a bit harder too, so that's nice. I really want that pulley drop now. I have more pics in my build thread, but here's the stock arms after 10k, still pretty clean IMO.
http://i14.photobucket.com/albums/a3...ps820af77d.jpg
She's dusty, but pretty. The dust is a proctective coating. I need a new (clean) coolant tank too:
http://i14.photobucket.com/albums/a3...psb751bf4b.jpg

Quote:

---

Originally Posted by Booba5185

Rockers are done, it seems to pull a bit harder, there was some noise from the rear but it seems to have fixed itself. Probably just needed to oil up a bit. We'll see. Pulls a bit harder too, so that's nice. I really want that pulley drop now. I have more pics in my build thread, but here's the stock arms after 10k, still pretty clean IMO.
http://i14.photobucket.com/albums/a3...ps820af77d.jpg
She's dusty, but pretty. The dust is a proctective coating. I need a new (clean) coolant tank too:
http://i14.photobucket.com/albums/a3...psb751bf4b.jpg

---

What rockers did you install?

ER's, I can't get 1.9s since I have an L32. I got them for $100 Shipped to my door, too so I couldn't pass it up.

My retros are completely sealed up. Just need to install the high beam connector and swap it in.

Quote:

---

Originally Posted by Booba5185

ER's, I can't get 1.9s since I have an L32. I got them for $100 Shipped to my door, too so I couldn't pass it up.

---

Why can't you put 1.9's on a L32?

There's been a few places I've seen recently that have said they make the push rods rub the head's casting. There's a thread around here somewhere on it...

Quote:

---

Originally Posted by Booba5185

ER's, I can't get 1.9s since I have an L32. I got them for $100 Shipped to my door, too so I couldn't pass it up.

---

ER's are typically for NA applications.

http://www.grandprixforums.net/threa...ould-I-replace

Quote:

---

Originally Posted by The Guz

ER's are typically for NA applications.

---

I know, but this was the best I could get away with on my heads, and they were a good deal. $100 shipped.

Quote:

---

Originally Posted by Booba5185

http://www.grandprixforums.net/threa...ould-I-replace


I know, but this was the best I could get away with on my heads, and they were a good deal. $100 shipped.

---

Heck yeah they were! Nice to seem them doing work and making someone else happy :-)

Quote:

---

Originally Posted by Booba5185

http://www.grandprixforums.net/threa...ould-I-replace


I know, but this was the best I could get away with on my heads, and they were a good deal. $100 shipped.

---

Never knew this. Good to know. Do they even make 1.8's anymore?

Also good write up on the injectors. I should clean the spares I have lying around that I removed since a couple are clogged.

I would say just run ERs vs 1.8s, you get 1.85 on one set of valves, I felt like I had better gains with the 1.85 on exhaust than intake, opposite of an NA setup because the supercharger can force the intake side.. just need a bit more exhaust flow. Just my $.02

Quote:

---

Originally Posted by Booba5185

There's been a few places I've seen recently that have said they make the push rods rub the head's casting. There's a thread around here somewhere on it...

---

I've had mine on for over 2 years now, so far so good....for now. I just checked ZZP`s website, I guess they`re keeping quiet, there`s nothing noted about it.

New strut and spring on the cavy this weekend. No more bounce.......

New fuel line on the ATV project. Still not getting gas, so took the carb off and will clean it when I find some time. Poured some gas in the head and it ran for about 3 sec or so.

That's great Joe!

I emptied out the backseat a bit. Still too much in there from the move and working on one of the houses. Was nice to see the seat again.

Tried to get the fuel filter off the cavy too. Not enough space and too rusted. Still chasing the miss. Gong to call my mechanic and have them look at it and the trans leak. Not feasible to sell cavy and purchase cheap w-body.

Donuts...lots of donuts. Waiting to see if the school says anything about the big black circles left in the parking lots.

Threw a P0650 this morning with no CEL so i got kinda confused but it never came back so no cares.

LOL.. you are confused why? Cause the code didn't return...or cause you dunno what it is.. ... or... cause your MIL does work?

http://www.gearchatter.com/viewtopic8985.php

Quote:

---

Originally Posted by Sven The Sexman

Donuts...lots of donuts. Waiting to see if the school says anything about the big black circles left in the parking lots.

---

for you Jay.

http://www.youtube.com/watch?v=1v3CzvQ9e_w

Quote:

---

Originally Posted by Scottydoggs

for you Jay.

http://www.youtube.com/watch?v=1v3CzvQ9e_w

---

LMFAO! Thanks Scotty. It was Saturday night...people said I wouldn't do it...so I did. LOL