Phenolic Intercooler for your Gen3/Gen5 M90, L67/L32 3800's - LOOK INSIDE

Quote:

---

Originally Posted by sseilmnop

They are on eBay.

http://pages.ebay.com/link/?nav=item...obalID=EBAY-US

---

Thanks! Will be buying. Do you still sell pulley pullers?

Sorry, don't do the pulley pullers anymore.

Quote:

---

Originally Posted by Cymaro

I was wondering if you ever got that finished. I'm not sure if a coolant temp gauge works the same way as a air temp gauge. I would think the coolant temp gauge needs to have liquid on it and are less sensitive to temp change.

---

I did, what ended up happening was the gauge I have has a range of 100 degrees F to 240 degrees F. so far it hasn't shown anything above 100, so I'm not real sure what the actual coolant temperature is. I'm in the process of fixing an exhaust leak, and when that is done, I have a different gauge that will display temps down to 64 degrees F. the way the gauge works is that there is a sensor in the front mount heat exchanger, so it reads the actual temperature of the coolant in the intercooler system. my next project will be to install an air temp sensor below the intercooler so I can see what the air temp is of the air going into the engine.

Quote:

---

Originally Posted by real diehl

Thanks! Will be buying. Do you still sell pulley pullers?

---

Quote:

---

Originally Posted by SgtMarshal

I did, what ended up happening was the gauge I have has a range of 100 degrees F to 240 degrees F. so far it hasn't shown anything above 100, so I'm not real sure what the actual coolant temperature is. I'm in the process of fixing an exhaust leak, and when that is done, I have a different gauge that will display temps down to 64 degrees F. the way the gauge works is that there is a sensor in the front mount heat exchanger, so it reads the actual temperature of the coolant in the intercooler system. my next project will be to install an air temp sensor below the intercooler so I can see what the air temp is of the air going into the engine.

---

Quote:

---

Originally Posted by sseilmnop

Sorry, don't do the pulley pullers anymore.

---

Sent from my Z970 using Tapatalk

That a lot of quotes.

Will it have any clearance issues with the 40th ann. hood?

Quote:

---

Originally Posted by USonuMabeaCh

Will it have any clearance issues with the 40th ann. hood?

---

Sorry not sure about your hood clearance. Someone else on the forum may?

Quote:

---

Originally Posted by sseilmnop

Sorry, don't do the pulley pullers anymore.

---

your sig says you do ...:th_scratchhead:

Quote:

---

Originally Posted by sseilmnop

Sorry not sure about your hood clearance. Someone else on the forum may?

---

I had hood clearance issues with my full size phenolic intercooler and special edition hood, but I had lowering springs with motor and transmission mount spacers to raise the engine and transmission back up in order to correct some of the axle geometry. so its possible my engine and transmission were a bit higher then they should have been. I have since removed the lowering springs and spacers, but I don't have the special edition hood installed anymore.

Quote:

---

Originally Posted by EHBGoober

your sig says you do ...:th_scratchhead:

---

Sorry use tapatalk on mobile and haven't read signature in awhile.

Is the price for the full-size phenolic intercooler for an L67 still the $549? I get paid on the 12th of this month and will most likely purchase one then. I have the aluminum one installed now and I want to try the phenolic one out to test any noticeable difference. I have a major vacuum leak between the intercooler and the LIM so i thought if i have to take it off i might as well upgrade to the phenolic.

I've been doing $554 including shipping to the USA.

Quote:

---

Originally Posted by sseilmnop

I've been doing $554 including shipping to the USA.

---

Okay that is basically the same. I'll order one from you sometime during the middle of this month.

my dumbass didn't realize that the outlet was bigger than the inlet on the gen 3. for some dumb reason I thought there were 3 different intercoolers, not the first time I've been wrong, and probably won't be the last

Quote:

---

Originally Posted by sseilmnop

Gen 3 intercooler w/ bolts $554
Gen 5 intercooler w/ bolts $554
New style is aluminum and phenolic. It is a full size core with more fins per inch than Zzp.
2-1/4" thick with working PCV

http://tapatalk.imageshack.com/v2/15...d8611e9f3d.jpg
Pulley Pulley $90 (rental $50 back) fits in flat rate envelope for $6 return shipping.
L67 throttle body to N* with working PCV $80 w/bolts and fitting.

http://tapatalk.imageshack.com/v2/15...6febfc5508.jpg

Gen 5 to North Star TB adapters shipped with bolts PayPal friend $80

http://tapatalk.imageshack.com/v2/14...401f1283aa.jpg


SKF Bearing kits with Nye oil and green couplers $45 shipped USA

http://tapatalk.imageshack.com/v2/15...3fb618fda8.jpg


All prices include shipping to USA PayPal as friend or add 4%

Adapters

http://tapatalk.imageshack.com/v2/15...244bdeb11e.jpg

---

Still for sale

What is the price for a snout rebuild kit with a pair of needle bearings for a Gen V? Is the oil seal a double lip design?

http://www.ebay.com/ulk/itm/261906037880

I sell them in eBay. The open needle bearings are pretty expensive.

Great and thank you. Is the oil seal a double lip design?

Yes. http://images.tapatalk-cdn.com/15/11...2c3385c605.jpg

It seems that Wbody store no longer offers their fuel rails, what are the other options for this?