I have a 04 GP with stock radio aftermarket rear speakers amp and subs. how can i get them to work with the stock radio. or can i.
|
|
11-24-2015
I have a 04 GP with stock radio aftermarket rear speakers amp and subs. how can i get them to work with the stock radio. or can i.
11-24-2015
Use a high to low level converter, it takes in speaker level outputs and steps them down to line level. As far as the turn on I was looking at that last night. I have a diagram for the 05' and it has speaker level and amp level outputs.
Jeff
11-24-2015
I have power to the amp but nothing going to the subs
11-24-2015
Need a better explanation, I can interpert that 4 ways.
Jeff
11-25-2015
The new amp is shot
Sent from my HUAWEI H892L using Tapatalk
11-25-2015
OK, I am not a dentist so I am not going to sit here and pull teeth to get information.
1 You state that you have aftermarket rear speakers, subs and amp.
Problem: You don't state what's hooked to where, nothing
Problem: Your new amp is "shot"
Now based on the little information you have given, I can't tell you the amp is shot. I can tell you that I have had literately dozens of people come to me to tell me their amp is shot only to find they had the box sliding around in the trunk and the remote turn on wire, one of the power wires, or it slid into something and broke the RCS's or damaged/knocked out the fuse.
Need Moar info, is I think what the kids say.
Jeff
11-25-2015
When I go the car the person that had it before me had it professional installed. The amp that was in it. Was bad because it keep blowing fuses. The amp I put in would not run the sub or the rear Speakers. I know its not the subs I hooked them to my home radio. They work. The have rca cable running from amp to rear deck speakers.
Sent from my HUAWEI H892L using Tapatalk
11-25-2015
What about your remote turn on and power wire fuse for the amp up front by the battery? What amp did you have and what amp do you have now. Model numbers please? Also typically RCA's are not connected to speaker level outputs (your rear speakers). If your old amp had line level inputs and the new amp doesn't then that's not correct. You would need a high to low level converter.
Jeff
11-25-2015
The remote turn on is hooked to the radio fuse. the one for the battery is a 50 amp fuse. The amp that was in it is XA-800I. The one that is now in it is autotek ATA800.2
Sent from my HUAWEI H892L using Tapatalk
11-25-2015
Does the light come on? what about eh protection light?
11-25-2015
Its a green light
Sent from my HUAWEI H892L using Tapatalk
11-25-2015
Do you have the RCA's connected to the line out?....Go look.
11-25-2015
Line in
Sent from my HUAWEI H892L using Tapatalk
11-25-2015
Tell me more about how you have the RCA's connected to the amp via the 6X9's
Jeff
11-25-2015
Can I put pics on here that might help
Sent from my HUAWEI H892L using Tapatalk
11-25-2015
That would be great.
11-25-2015
Upload your pictures to Photobucket then post the IMG link.
11-25-2015
Another question I have is how do you have the amp connected to the speakers and what is their impedance, are they dual or single voice coil. If the previous amp failed then perhaps it was driving a load that is to low. Your amp is only 2 Ohm stable and if you are driving it bridged into both speakers and they are not 8 ohms then that amp will fail as well.
Jeff
11-25-2015
http://s1382.photobucket.com/user/Ra...tml?sort=3&o=2
Sent from my HUAWEI H892L using Tapatalk
11-25-2015
Tell me if there is 3 photos there
Sent from my HUAWEI H892L using Tapatalk
| « Previous Thread | Next Thread » |
| Bookmarks |
Bookmarks |
