holy **** I just remembered I have to have this done by next thursday...
|
|
10-04-2011
holy **** I just remembered I have to have this done by next thursday...
10-05-2011
Got some pictures for you all first one is a little ahead of the game but I had to do it
heres the stuff I pulled from the head that was on the car to use in one of the l67 heads
Heres the L67 heads as they sit now all they need is a valve job and their good to go
10-06-2011
on those headers cant u just wrap em
SMGPFC #77
10-06-2011
Idk but at this point there not getting coated before kcgp11 I'm just putting them on and maybe throwing them on and hopeing for the bestOriginally Posted by cliffdawg
10-06-2011
So thank god Nick pointed out how long it takes to get stuff you buy on ebay... so I ordered my sd headers a few minutes ago estimated arrival is the 10th-14th I hope its leaning more towards the 10th side!
the good news is that is the last thing I had to buy to finish the job I hope... also hope the valves work out all right... I don't see any reason for them not to but everyone else is shaking their head yet they can't actually tell me why they feel that why
10-06-2011
i got my sd's about 4 days after i ordered them so hopefully you have similar luck
10-06-2011
oh by the way paul is coming over here next week so if you want a tune...
10-06-2011
what day and how much?
10-06-2011
10-07-2011
I can't see your picture Yooo.
Oh wait..it's where I'm at..lol
10-07-2011
head looks nice.. im assuming red and not orange lol
10-07-2011
Very nice so far!
What are you using for fuel rails? I'm assuming L67 rails? Is that brake booster really that rusty or is it the picture? lol
10-07-2011
its surface rust its not that bad but yea it happen awhile ago
10-07-2011
so how the hell do you guys go about removeing the rear head while on the car? main part is I can't figure how the **** to get the rear manifold off I wish I had a engine hoist this would be so much easier if the engine was out of the car
10-07-2011
you dont have headers on it?
Just undo the bolts. should be something like 6 on the rear manifold to the head + one for the EGR. Crossover is two, downpipe is two. unplug O2 sensor and leave in manifold.
Should lift right up.
Can't really remember though. Been a while...
rear head isn't bad. Its just a stretch on the legs and back.
10-08-2011
I'll find a way I guess
10-09-2011
so I got a good bit done today and still have much more planned
the good news is I got the rear head off wasn't as bad once I pulled the engine forward.
my plan is by the end of the day to have all the wires re routed to finish up my wire tuck I started earlier in the summer.
along with that I want to have all the fuel line and rail stuff finished and the new connectors for the injectors installed.
I still got a lot of work but I need to have the heads and LIM on by tommorrow night
10-10-2011
whats the fuel pressure regulator look like? I'm not sure if I have one : / also paul can't drive over here to tune my car because of his transmission... is there anyway I could drive my car and hour over there on my old tune? or would it be best if I run over there pick him up drive back to my place have him tune my car and then drop him off on the way to kcgp lol this is all just mess isn't it I want a god dam trophy if I make it to this thing
10-10-2011
There was a fpr on the rail you got from me, give me a min and i'll send you a pic of it. You should be able to drive on your old tune just leave your sc belt off until its tuning time. Just don't get on it at all.
10-11-2011
| « Previous Thread | Next Thread » |
| Tags for this Thread |
| Bookmarks |
Bookmarks |
