How are the high beams? They were absolutely worthless on my spyders.
|
|
08-30-2011
How are the high beams? They were absolutely worthless on my spyders.
08-30-2011
High beams are actually very good, beats my stock cloudy housings by far. It's nice to be able to see again lol.Originally Posted by 4THGENCAMAROFAN
08-31-2011
Morimoto bi-xenon hi beams..... lets compare go find a big building cam!
Mori low beams.....
On a side note they look alright minus the leds and halos and the mucked up cutoff but to each his own........
For $150 bucks if that's what you paid you did ok cam....
Last edited by cleangtp; 08-31-2011 at 12:24 AM.
08-31-2011
Yes, I paid 150, and ill get a better picture of the cutoff line, that was my ****ty camera on my phone, it kinda blurred it out. And i already know you hate the halos and LED's lol.Morimoto bi-xenon hi beams..... lets compare go find a big building cam!
Mori low beams.....
On a side note they look alright minus the leds and halos and the mucked up cutoff but to each his own........
For $150 bucks if that's what you paid you did ok cam....
08-31-2011
Hate is a strong word I dislike..... I think they belong on riced out Hondas or should only be on cars that come like that from the factory like bmw's, audi's etc....
For $150 you did ok but the bulbs in those aren't H1's mang I'm almost positive they're H3's......
08-31-2011
I think the spec-d's look really cool. We had a set and ran vision plus bulbs to get more light out of them. Do you have a bounce problem? I had to use weather stripping under the bumper cover and under the light to get ours to stop bouncing. Ours would always get water in them however even after sealing them three times. The rubber boots rotted, the halo bulbs burned out and the replacements were all different colors and shades. There is no adjustment for the high beams. Basically they are a bad design (bouncing) and poor quality. Hopefully you can get yours to stay lit, clear of water and not bounce. I went back to OEM's with HID 6000's
08-31-2011
True, It says H1 on the back of the light housing, so I assumed there H1's. But, H1's and H3's look fairly similar, How can you tell it's H3?
08-31-2011
I was under the impression that the 3 led projector lights used H3 bulbs in the projector. I'm pretty sure there's a thread about it on here somewhere... maybe I'm wrong
09-02-2011
damn clean i want your headlights lolMorimoto bi-xenon hi beams..... lets compare go find a big building cam!
Mori low beams.....
On a side note they look alright minus the leds and halos and the mucked up cutoff but to each his own........
For $150 bucks if that's what you paid you did ok cam....
09-02-2011
Thanks Hot but I've got my own thread so any future posts should be posted there. I didn't mean to totally hijack cams thread here just showing the differences........
Actually for $150 shipped those headlights look decent def better than stock....
09-03-2011
hey I got the same hood yours from stinger fiberglass? Arn't worried about running it without hood
pins?
09-03-2011
Umm no the factory hood latch is plenty fine!!!
Also Naw that's how I would want my ebay projectors to run no halos no leds looks much much better this way imo....
09-03-2011
Its not the latch you have to worry about failing, its the fiberglass in the hood iteslf.
09-03-2011
Ok thanks I've had my GTX hood for over a year it's constructed very well. Good lord it isn't made out of wet toiltet paper I don't have a clue where you're coming from. Hood pins would look hideous, and you don't freakin need them.
| « Previous Thread | Next Thread » |
| Tags for this Thread |
| Bookmarks |
Bookmarks |
