This info used to be posted on the Canada Club GP but its gone. There was info for bright blubs inside and out, one was tail light blubs (good for guys with darker tails). Anyone have this info?
Thanks
|
|
02-02-2008
This info used to be posted on the Canada Club GP but its gone. There was info for bright blubs inside and out, one was tail light blubs (good for guys with darker tails). Anyone have this info?
Thanks
02-02-2008
Shawn, I dont have an answer for you, but I am going to watch this thread because we had a discussion going on about the affect of tinted tails on light output, particularly during the day.
02-02-2008
i'm sure there must be some brighter bulbs, but with brighter comes more heat... i'm sure there's a fine line in there that might be too warm
though i remebmer seeing somewhere 55W backup lights.....
02-02-2008
Bringing up the heat is a good point. I wonder if there is anyway to determine where the cut off point would be other than real world experimentation?
02-02-2008
Originally Posted by SyntheticShield
i suppose if we found a chemist that was familiar with the specifications of the plastic used in the tail lights....
but, i suppose there is a decent amount of space in the light, so it shouldnd be THAT sensitive
02-02-2008
would a small vent hole help it also? In a place that wouldn't let in water of course
02-02-2008
I was thinking about that earlier. One on top or over the top of the bulb would be good, but then, of course, you have the possibility of water intrusion. You could put one on the bottom but , of course, heat rises so it probably wouldnt be all that effective.
You would be better off with something that gave you a little air flow I would think.
02-02-2008
LED anyone?
02-02-2008
Would they be bright enough to deal with the NightShade during the daytime?
02-02-2008
3457.
02-03-2008
didnt think they were that much brighter?
Last edited by Toasty; 02-03-2008 at 01:40 AM.
02-03-2008
Thanks BNB. Any idea on how much brighter these are? What are stock blub sizes?
02-02-2008
LED's are bright! plus take less power...less heat.
02-02-2008
This is true, but are they bright enough to get through the NightShade coatings?
02-02-2008
i have a feeling they would be.
it's times like these that i wish i had my old automotive lighting spec book
02-02-2008
Well if that is the case, I may have to find me a spare set of tail lights and try that out.
02-03-2008
you'll still need to add in the resistor modules, if you dont want to hack up your flasher.
--- but ---
guess what?
i've come up with a plug and play solution for the resistor modules
02-03-2008
See, there you go teasing us again. We need details man, details
guess what?
i've come up with a plug and play solution for the resistor modules
02-03-2008
See, there you go teasing us again. We need details man, details
well, lets see ---
the tail light harness is one plug on the passenger side of the car. you have access to the left, right and ground here. all that needs to be done is get the male and female plug housings (and terminals) (yes these parts are readily available) and the load resistors, and wire up a short extension harness with the load resistors in it, and plug it in. Obviously, you need to be able to mount the load resistors somewhere. i did some looking, and it should be possible to get a fairly inexpensive aluminum box to put them in and attach them, which will also help with heat dissipation.
if i get the $$ for some decent tail light housings, i'll probably put this together
anybody wanna donate a good set of tails in exchange for one of these harnesses?
02-03-2008
details or ban dangit lolyou'll still need to add in the resistor modules, if you dont want to hack up your flasher.
--- but ---
guess what?
i've come up with a plug and play solution for the resistor modules
| « Previous Thread | Next Thread » |
| Tags for this Thread |
| Bookmarks |
Bookmarks |
