Re: 98 GTP progress/build thread PIC HEAVY!!!!
Re: 98 GTP progress/build thread PIC HEAVY!!!!
Almost ready to drop in... I'll be buying my rack pump and lines in the next couple days and once that is done and I clean up what I can in the engine bay it will go back in.
Just tossed the header on for effect
http://i1236.photobucket.com/albums/...s/IMG_2720.jpg
I ended up just using a flywheel I had, I picked this one cause it had the least holes drilled for balancing. I figure I'll be doing something with the trans(5spd/built auto) soon enough and I'll do something then.
http://i1236.photobucket.com/albums/...s/IMG_2714.jpg
Re: 98 GTP progress/build thread PIC HEAVY!!!!
Re: 98 GTP progress/build thread PIC HEAVY!!!!
Very nice build thread, wish I had the motivation you have. Hope to see videos some day.
Re: 98 GTP progress/build thread PIC HEAVY!!!!
Someone I missed this one.
Nice.
Re: 98 GTP progress/build thread PIC HEAVY!!!!
you should powder coat or paint the S/c. lookin good mane looks like youll be back on the road soon
Re: 98 GTP progress/build thread PIC HEAVY!!!!
Thanks for all the compliments everyone!
Quote:
Originally Posted by
TexasTanker19kilo20
Very nice build thread, wish I had the motivation you have. Hope to see videos some day.
It was more the bent flex that did it for me, I woulda been fine with the parts sitting til summer at least...lol And there will be videos a plenty when I get it all done.
Quote:
Originally Posted by
squeeze
you should powder coat or paint the S/c. lookin good mane looks like youll be back on the road soon
I plan on pulling the blower sometime soon to remove the H-bar and do some light porting/smoothing and I will for sure be doing something about the finish of it. Would really like to have it polished, maybe next Christmas...
Re: 98 GTP progress/build thread PIC HEAVY!!!!
So nice... can't wait to see more :D
Re: 98 GTP progress/build thread PIC HEAVY!!!!
Re: 98 GTP progress/build thread PIC HEAVY!!!!
Curious: Did you degree the cam?
Re: 98 GTP progress/build thread PIC HEAVY!!!!
Quote:
Originally Posted by
matt5112
Curious: Did you degree the cam?
I really wish I coulda but nobody I asked had a kit I could borrow, and I wasn't gonna pay nearly $200 for a new one. I've never really noticed anyone else do it on other builds either.
Re: 98 GTP progress/build thread PIC HEAVY!!!!
Yeah, I asked because I just realized no one does it.
Yet everyone has differing results.
Perhaps this is a factor.
Its fun talking to SBC guys, they're amazed I'm running 9 PSI on 9.4:1 CR with iron heads, hypereutectic pistons, cast rods and crank etc.
Re: 98 GTP progress/build thread PIC HEAVY!!!!
Quote:
Originally Posted by
matt5112
Yeah, I asked because I just realized no one does it.
Yet everyone has differing results.
Perhaps this is a factor.
Its fun talking to SBC guys, they're amazed I'm running 9 PSI on 9.4:1 CR with iron heads, hypereutectic pistons, cast rods and crank etc.
I've always wondered that myself why I don't think I've ever seen a 3800 build where someone degreed the cam... That's who I was asking was a few buddies into SBCs. They think I'm crazy "wasting time on a v6" I'll bet if anyone degrees their cams it would be Bill, maybe he will see this and enlighten us...lol
Re: 98 GTP progress/build thread PIC HEAVY!!!!
Well so far I'm making more power than mild 305 with 231 cubes.
I'd say thats one reason to bother.
Next step, stout 350 territory. :D
Re: 98 GTP progress/build thread PIC HEAVY!!!!
Quote:
Originally Posted by
matt5112
Well so far I'm making more power than mild 305 with 231 cubes.
I'd say thats one reason to bother.
Next step, stout 350 territory. :D
Then I tell them my predicted HP goals for this thing and they start asking all kinds of questions and then when they run outta questions they kinda just agree... And I always ask if they have heated leather, moonroof, HUD and all the other perks of being a GP owner. Or are there any other perks???
Re: 98 GTP progress/build thread PIC HEAVY!!!!
My 1-2 shift takes 750 RPM now. :D
Re: 98 GTP progress/build thread PIC HEAVY!!!!
I wouldnt expect anything less kevin really nice job man
Re: 98 GTP progress/build thread PIC HEAVY!!!!
Quote:
Originally Posted by
thunder71173
I wouldnt expect anything less kevin really nice job man
Thanks Dave
More updates:
Decided after emailing a bit back and forth with the intense guys trying to verify these heads authenticity, that I need to double check spring #. So I pulled the cover and one spring to take to the local machine shop and have them measure it for me tomorrow. Weighed the retainer to verify it was titanium while I had it off and it's the lightest of the light titanium retainer apparently, which is great news cause I get's faster revs and less float! and here's the pics...
Installed a few more brackets and the starter
http://i1236.photobucket.com/albums/...s/IMG_2741.jpg
Anyone got a guess before I have them measured? The guy told me 150's, the S2 heads are supposed to come with 105's. But then again the S2 heads aren't supposed to have titanium retainers normally either.
http://i1236.photobucket.com/albums/...s/IMG_2743.jpg
Proof
http://i1236.photobucket.com/albums/...s/IMG_2739.jpg
Info on them
http://i1236.photobucket.com/albums/...s/titanium.jpg
The cleanest I could get the stock 185K starter... I would know if it was replaced I got every receipt for everything from new from the original owners
http://i1236.photobucket.com/albums/...s/IMG_2745.jpg
Re: 98 GTP progress/build thread PIC HEAVY!!!!
150 seat pressure?
Because thats a lot.
at ~1.78 compressed height?
Re: 98 GTP progress/build thread PIC HEAVY!!!!
Quote:
Originally Posted by
matt5112
150 seat pressure?
Because thats a lot.
at ~1.78 compressed height?
I've seen 1.770" somewhere but the intense guy told me to measure them at 1.800" They recommend 130's for this cam so it wouldn't be too much overkill, and I got the double row(bout to post on that thread, read it). I am hoping he was just not remembering and they are 130's but I'm not gonna switch if they are 150