|
|
05-20-2018
Rear pads on the 05 GP, also bought the "cube". BTW Mobil rebate is in effect until 5/31/18. Various amounts based on what you purchase. I got a 5qt jug high mileage synthetic & extended perf oil filter for $33 plus tax. Gonna get $ 17 rebate. So all in around $ 18. Two rebates per household.
05-20-2018
Slapped a stubby cone air filter on the GTP for full whine during windows down weather. Last week I had the Catalina body at work up off the frame first time since I made the floor. It did not fold in half on the lift.
05-21-2018
Bought a trans, front brakes (rotors and pads), washer fluid, oil change, trans filter and wheel paint. Picked up my buddies atv jack to install the trans tomorrow when it's out of it's current car. Need to get some trans fluid and probably finish pulling trans tonight. The axles are out, ball joints separated, engine and trans mounts undone, bell housing bolts out except two, brakes removed since they are being replaced. Trans lines arrive tomorrow.
It'll be ready to sell by about Wed night when the air filter arrives. Already cleaned the interior and detailed the exterior.
2006 GT with 93K on the clock and almost no signs of any rust at all.
05-21-2018
Paid a visit to an LKQ salvage today. Didn't strike gold by any means but did leave with new clips for the doors, and trunk as well as a driver floor matte and center console lid and that tiny storage net in the trunk. There was a Bonne GXP w rims still attached to it that were super tempting, did'nt get em. Couldn't spend that much money.
05-21-2018
Not grand prix related, but been working on my wife's aztek today getting it ready for inspection. Thought I'd post a before and after on the headlights. Makes a BIG difference!
05-21-2018
Flipping a Grand Prix for spending money? How's it feel to be slumming it with a w-body in the garage again?Originally Posted by BillBoost37
05-23-2018
Fixed driver door lock in the GXP. It was a cut wire. I'm now stuck with a brand new lock actuator. =/
05-24-2018
Well Brandon.. it's fun. Scotty told me to call you and ask for the loaner tool special on trans tools lol.
Got that trans on Tuesday and flipped it into the car. Had everything buttoned up except wheels and pulled the pan to find a piece of the forward band hanging out of the hole where it resides. Called place yesterday morning and then located another trans nearby. (05 Impala SC this time 80K). Drove the 40 mile round trip to get new trans, had buddy help me move that from truck to floor and broken trans back into truck to drive the 70 mile round trip to bring that back. Get back home and stuff this impala trans in, it's ready for a pan drop to do filter and then it'll get it's wheels back on it.
Hoping for the best.
05-27-2018
Re-re-retinting tail lights. This time they'll be getting a thick clear coating.
05-28-2018
If you have access to a compressor ( I used a Porter Cable pancake) pick up a Harbor freight purple HVLP gun. I used quart cans of duplicolor lacquer black and clear.
Tinted clear for a few coats then a lot of just clear after. The lacquer sets pretty quick so you can get it done quick.
Ideally urethane would be the way to go.
05-29-2018
Ordered an LS6 intake manifold. Comes with fuel rail and injectors. Guess I'm finally doing the intake swap.
05-29-2018
Junkyarded..
Got fans, evap, lock knobs.. it was productive. Got a wiper motor for buddies trailblazer. Got home and was sanding the crappy wheels with dremel when it went up in smoke. Finished sanding by hand, then cleaned them down and painted them up. All 4 wheels now look good. Also tossed in the fans and evap.
it's one mirror painting away from being listing.
06-02-2018
Made boom-boom. Well, boom. LOL
06-03-2018
Not what I did to the car, but what the car did to ME!!
This will be my first "big" repair outside of changing things like belts/spark plugs/pulley+tensioners or interior motors. Semi excited and I hope it goes well, I bought 2 strut spring assemblies and 2 lower control arms with all the bushings. I'll have to take a look at how the sway bar is again and see if I can get away with just replacing the bushings, otherwise it's another 120 dollars for a new one.
06-03-2018
struts are easy, nothing hiding there to surprise ya.
that does suck, looks like it cost ya a tire too?
dorman 33 mm solid bar is like 70 ish shipped with new end links and bushing.
myself. i did a hub swap. no more noise from the car.
06-03-2018
Yep unfortunately it'll take a new tire as well, since the spring managed to carve right in to the tire. There's far too much thread exposed for me to ever comfortably use it. Sadly things cost a bit more in Canadaland! It makes me cry a tear or two seeing how cheap parts are down south.
06-03-2018
if your close to the boarder ive heard of guys having a po box here in the states or at someones house in the U.S. near your local crossing for a mailing addy, then take a day trip over the boarder, install your parts and go home.
06-03-2018
Washed and waxed 2 suburbans a murano and a benz gle 350. No love for a grand prix today.
My arms are tired.
Sent from my iPhone using Tapatalk
06-03-2018
thats like doing 6 cars, not 4 lol
markpa liked this post
06-03-2018
That's true Scotty, I plan on moving a bit closer to the border for work at some point so that will definitely be an option later.
| « Previous Thread | Next Thread » |
| Bookmarks |
Bookmarks |
