Thread: What did you do to your Car today?

Originally Posted by Russosaur

Oh that, I'm worried about that a lot lol. I don't want to have to try to rotate the projector.

Classy should handle that

He promised them to be level so im not worried.

Originally Posted by 98FvckingCrazyVet

Im lost whats the point of ND oil?
Only ND oil i know of comes from the state lol !!!

Non detergent oil. It's for older engines that weren't designed for oils in today's market. I'm not a 100% on it but I think this will be good for this old tiller.

Sent from my HTC6525LVW using Tapatalk

it wont matter really, its way past the break in period, or warranty time lol

Originally Posted by Scottydoggs

it wont matter really, its way past the break in period, or warranty time lol

Agreed. I just don't wanna run synthetic or anything in it. Figured a heavier weight oil that is non detergent would be best

Sent from my HTC6525LVW using Tapatalk

those little engines will run forever if the oil is changed and they aren't left with gas in the carb for years on end unused.

good rule of thumb with any engine in dirt and dust with a the air filer so low is to clean the foam part of the filter every tank of gas or two, depending on how dusty. gas rinse, and re oil the foam, oil stops the dust from getting to the paper filter or inside the carb.

Originally Posted by Scottydoggs

those little engines will run forever if the oil is changed and they aren't left with gas in the carb for years on end unused.

good rule of thumb with any engine in dirt and dust with a the air filer so low is to clean the foam part of the filter every tank of gas or two, depending on how dusty. gas rinse, and re oil the foam, oil stops the dust from getting to the paper filter or inside the carb.

See when I inherited it it hadn't had an oil change in forever. Runs great though. I'll post pics later it's almost completely apart. Cleaning the poop out of it.
I'm looking for an air filter solution now. The one it has stock is a metal mesh **** and for some reason it's greasy and dirty as ****. I'm also taking the carb apart for Cleaning as we speak. And looking for a few parts for it.

Sent from my HTC6525LVW using Tapatalk

if theres foam inside its cause it was oiled then sucked dust into it.

what you can do is relocate the filter to the handle bar or the bar up to it. kinda like a hai on the car, hose, clamps and a bar to mount the new filter to for support. you'll need to get a new style filter tho. your local lawnmower shop may have used parts for sale, or ebay has stuff like this too.

Yea this piece of history will never see real dirt again lol. I'd like to keep it looking original but don't think I can. The air filter is going to have to be custom. There is no foam in stock one at all. Just a metal mesh. Dad never oiled the filter lol. Also I'm going to have to use gasket maker for replacing gaskets with as I don't think I'll find replacements.

Sent from my HTC6525LVW using Tapatalk

I washed it. Drove it around
Did this to piss red off since someone hit it and ran a while ago. I couldn't get it all popped out.





And took and edited some pics cause I was bored

I got the left LCA installed today, after doing the right yesterday. A little less clunk and squeak going on up there now.

I may have made a fairly large purchase for it today..

Rewired this for the remote start setup, this will allow me to roll the windows up and down.

Here's the remote for it all

Hey make it so your car will drive up to you, so you don't have to walk through parking lots

Someday, lol.

Made an offer on an HV3. He declined.......i'm too cheap sometimes. lol

Someone on Facebook few weeks ago was selling an l26 hv3 for 75.

That's what the seller countered with. I offered $50 because I can......

I have no FB so no cares are given

Pissed red off more
Edit. Also my dads turbo dart got a turbo snail sticker