Thread: Remote Start Install Questions

Results 1 to 5 of 5
  1. #1 Remote Start Install Questions 
    SE Level Member
    Join Date
    Dec 2011
    Location
    Detroit
    Posts
    3
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Hello Everyone as you can see this is my first post... now that were past that i have a question.....

    I have a 2004 gt2 Grand Prix i'm currently know where near my home for about another 2 months and i have a Avital Remote start system and a Dei Bypass module ... I've done 1 or two remote start installs on other cars Easily this one puzzles me.... Of course the avital has a relay harness that has some pretty heavy gauge wires in it which is normal , however under the dash on my GP i see no heavy gauge wires ... just the 16 gauge wires so where do i connect this harness i have a pretty good diagram that has a couple pics most wires are on the bcm plugs... Where do i connect these wires ????? any help would be appreciated...

    AvitalĀ® 4103

    Reply With Quote  
     

  2. #2 Re: Remote Start Install Questions 
    GT Level Member Brian99SE's Avatar
    Join Date
    Dec 2011
    Location
    Cadiz, Ky
    Posts
    242
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Source: Car Alarm, Car Stereo, Mobile Video, and Cruise Control Info for Installers

    DIRECTWIRE™ WIRING INFORMATION - PONTIAC / GRAND PRIX / 2004 / Remote Start

    [PRINT THIS PAGE]

    12volts red (50A), red (40A) + back of fuse box, passenger dash
    Starter yellow + ign harn or BCM, conn. C1, pin 21
    Notes: The BCM (Body Control Module) is below the driver side dash to the left of the steering column.
    Second Starter N/A
    Ignition pink + ign harn or BCM, conn. C1, pin 22
    Notes: The BCM (Body Control Module) is below the driver side dash to the left of the steering column.

    There are two pink wires in the BCM plug that meter as ignition. To verify that the correct wire is being energized for remote start, slide the key in the ignition key cylinder and then activate remote start. If the key in ignition warning chime comes on, then the correct wire is being energized.
    Second Ignition N/A
    Third Ignition N/A
    Accessory brown + ign harn or BCM, conn. C1, pin 23
    Notes: The BCM (Body Control Module) is below the driver side dash to the left of the steering column.
    Second Accessory N/A
    Keysense lt. green - ign harn or BCM, conn. C1, pin 40
    Notes: The BCM (Body Control Module) is below the driver side dash to the left of the steering column.

    If the service security lights comes on during remote start or after key takeover, see DirectFax document 1502.
    Power Lock red/black - BCM, conn. C2, pin 2
    Notes: The BCM (Body Control Module) is below the driver side dash to the left of the steering column.
    Power Unlock orange/black - BCM, conn. C2, pin 11
    Notes: The BCM (Body Control Module) is below the driver side dash to the left of the steering column.
    Lock Motor gray 5wi BCM, conn. C2, pin 52
    Notes: The BCM (Body Control Module) is below the driver side dash to the left of the steering column.
    Unlock Motor tan 5wi BCM, conn. C2, pin 46
    Notes: The BCM (Body Control Module) is below the driver side dash to the left of the steering column.
    Parking Lights+ brown + front of fuse box, passenger dash
    Parking Lights- brown/white - BCM, 18 pin plug, pin 8
    Notes: The BCM (Body Control Module) is below the driver side dash to the left of the steering column.
    Hazards tan - BCM, 18 pin plug, pin 16
    Notes: The BCM (Body Control Module) is below the driver side dash to the left of the steering column.
    Turn Signal(L) use hazards wire
    Turn Signal(R) use hazards wire
    Reverse Light lt. green + BCM, conn. C2, pin 42
    Notes: The BCM (Body Control Module) is below the driver side dash to the left of the steering column.
    Door Trigger see notes - BCM, conn. C2
    Notes: The driver door trigger is gray/black in pin 26, the front passenger door is black/white in pin 17, the left rear door is lt. blue/black in pin 7, and the right rear door is lt. green/black in pin 5. Use all four wires and diode isolate each.

    The BCM (Body Control Module) is below the driver side dash to the left of the steering column.
    Dome Supervision gray/black + BCM, conn. C1, pin 43
    Notes: The BCM (Body Control Module) is below the driver side dash to the left of the steering column.
    Trunk/Hatch Pin red/black - BCM, conn. C2, pin 3
    Notes: The BCM (Body Control Module) is below the driver side dash to the left of the steering column.
    Hood Pin N/A
    Trunk/Hatch Release lt. blue + BCM, conn. C2, pin 45
    Notes: The BCM (Body Control Module) is below the driver side dash to the left of the steering column.
    Power Sliding Door N/A
    Factory Alarm Arm lt. green - BCM, conn. C2, pin 22
    Notes: The BCM (Body Control Module) is below the driver side dash to the left of the steering column.
    Factory Alarm Disarm purple - BCM, conn. C2, pin 24
    Notes: The BCM (Body Control Module) is below the driver side dash to the left of the steering column.
    Disarm No Unlock see factory alarm disarm
    Tachometer white ac ignition control module, pin E
    Notes: The ignition control module is on top of the engine towards the passenger side.
    Wait to start N/A
    Brake Wire white + BCM, conn. C2, pin 30
    Notes: The BCM (Body Control Module) is below the driver side dash to the left of the steering column.
    Parking Brake orange/black - BCM, conn. C2, pin 9
    Notes: The BCM (Body Control Module) is below the driver side dash to the left of the steering column.
    Horn Trigger black - BCM, conn. C1, pin 4
    Notes: The BCM (Body Control Module) is below the driver side dash to the left of the steering column.
    Memory Seat 1 N/A
    Memory Seat 2 N/A
    Memory Seat 3 N/A
    Interface Module: Category:
    Immobilizer Bypass Required:
    Yes Type:
    PASS-Key III
    Part #: 556UW
    Alternate Part1 #: DesignTech 20402
    Alternate Part2 #: DesignTech 29402
    99 Grand Prix SE-Blue CAI, 3.03 GR Transmission, U Bend Delete.
    time to call the exterminator
    Reply With Quote  
     

  3. #3 Re: Remote Start Install Questions 
    SE Level Member
    Join Date
    Dec 2011
    Location
    Detroit
    Posts
    3
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Thanks i have that dia gram i even have on with pictures of each wire.However my question is my remote starter has a Relay harness of thicker gauge wire. the wires in the car are 16 gauge which is much smaller,am i to attach the heavy gauge wire to the smaller wires ?? or is there another place ..
    Reply With Quote  
     

  4. #4  
    SE Level Member Compg4me's Avatar
    Join Date
    Dec 2011
    Location
    Grand rapids Mi
    Posts
    116
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    You attach the heavy gauge wires to the correct smaller gauge wires if the ignition switch. The 12 volt power must be run to the back of the fuse box where there is a higher amp wire or run directly to the battery.
    Reply With Quote  
     

  5. #5 Re: Remote Start Install Questions 
    SE Level Member
    Join Date
    Dec 2011
    Location
    Detroit
    Posts
    3
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Quote Originally Posted by Compg4me View Post
    You attach the heavy gauge wires to the correct smaller gauge wires if the ignition switch. The 12 volt power must be run to the back of the fuse box where there is a higher amp wire or run directly to the battery.
    Thank you very much i was curious because in previous cars all the wires werent so small thanks again
    Reply With Quote  
     

Similar Threads

  1. A few questions about 2007 Remote Start
    By krpiper in forum Audio, Security & Visual Electronics
    Replies: 7
    Last Post: 02-24-2017, 11:45 AM
  2. Remote start questions
    By semocoachworks in forum General Tech Discussion
    Replies: 4
    Last Post: 01-14-2012, 03:33 PM
  3. how hard is it to install an alarm with remote start
    By nascartech in forum Audio, Security & Visual Electronics
    Replies: 3
    Last Post: 11-01-2010, 05:55 PM
  4. Need Help On Troubleshooting Bulldog Security Remote Start Install
    By eb97951 in forum General Tech Discussion
    Replies: 0
    Last Post: 12-24-2008, 07:39 AM
  5. Remote Start Install Questions...
    By Incomudrox in forum Audio, Security & Visual Electronics
    Replies: 1
    Last Post: 12-02-2008, 02:19 PM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •