Port and polish

**BLUESMOKEGTP** · 12-07-2014

Who ports and polishes as well as powdercoat supercharger. Ive got a gen v and need pricing

**16MustangVet** · 12-07-2014

Usually gen5s are not worth doing. If anything just the inlet a little is all people ever do. Not worth it IMO.

**CrazyGuy03** · 12-07-2014

Polish the casing , make it look like a mirror

**Fivefingerdeathpunch** · 12-07-2014

Yeah it's not worth it to port and polish a GEN V, it will likely only make it perform worse.

As for powdercoating, they has to be somewhere within 30 miles of you that does it. If you live by any bigger cities.

**BrandonHall10** · 12-07-2014

Or, if you have an electric oven, you can DIY:

http://www.eastwood.com/dual-voltage...html?reltype=3

**HighOctaneRacing** · 12-07-2014

Originally Posted by Fivefingerdeathpunch

Yeah it's not worth it to port and polish a GEN V, it will likely only make it perform worse.

As for powdercoating, they has to be somewhere within 30 miles of you that does it. If you live by any bigger cities.

is it because the GenV is already perfect or what?

**BLUESMOKEGTP** · 12-07-2014

What do you mean by polishing to a mirror finish

**16MustangVet** · 12-07-2014

Hes talking the outside of the blower case not the inside.

**Scottydoggs** · 12-07-2014

**BLUESMOKEGTP** · 12-07-2014

Oh ok i understand. Most powdercoater do that rite. Do i disassemble the supercharger prior to the powdercoating. One last thing who would happen to rebuild superchargers and shave the snout to run smaller pulleys

**ADrugDealer** · 12-07-2014

Yes you would take it apart completely. You can get a snout machine tool from ZZP for a rental fee and just use that. As for a rebuild, you need a hydraulic press so I think most just buy a reman snout.

**Fivefingerdeathpunch** · 12-07-2014

If you plan on running something smaller than a 2.7in pulley on there, then worry about machine work on the snout. You'll never go that low, thats some pretty extreme modding if you think you'd need to spin that thing that fast.

**BLUESMOKEGTP** · 12-08-2014

Thanx guys for the input. I found a gen v at the jy so i got it. Rotors are coated pretty damn good. I shouldve gotten the lim but didnt bring much as far as tools so if anyone has a lim layin around let me know

**Scottydoggs** · 12-08-2014

you didnt have a 3/8 th socket and a 13 mm? go back and get that. be cheaper from the jy then bought and shipped.

or just cut your gen 3 lim hole larger.

**REDCRAPGP** · 12-08-2014

Originally Posted by Scottydoggs

you didnt have a 3/8 th socket and a 13 mm? go back and get that. be cheaper from the jy then bought and shipped.

or just cut your gen 3 lim hole larger.

This! It's easy enough to to remove and shouldn't cost to much.

Sent from my iPhone using Tapatalk

**BLUESMOKEGTP** · 12-08-2014

Believe it or not i didnt go out there with any tools. I went to the jy to find seats for my 90 xr7 and happened to see the l32 in the jy. I will go back out there this weekend and grab it off if its still there

**BLUESMOKEGTP** · 12-08-2014

I can do it just didnt have any tools. I asked a guy taking a car apart next to me to use his 10mm and ratchet

**blowngtp00** · 04-05-2015

Sorry to change subjects a little bit, but how hard is it to PnP a M90 blower? And what gains could I realistically expect to get from doing this?
I'm getting ready to put a N* TB on and I have a CAI. What else should I do to let the engine breathe that much better? Thank you for help and support.