Thread: Doing cam and header build, any tips?

Results 1 to 4 of 4
  1. #1 Doing cam and header build, any tips? 
    GT Level Member
    Join Date
    Mar 2012
    Location
    South Beloit, IL
    Posts
    318
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Good morning everyone. Well, today is the big day. I'm doing a VS camshaft install with 90 # valve springs, new retainers, seals, etc. and SD Headers, as well as LIM, SC, Front cover, TB, and VC Gaskets. I followed this guide in terms of what to expect:
    Cam installation L67 - TECH - 3800Pro.com Forum

    I have mostly everything he speaks of in this guide, except the valve seal installer. Is that worth purchasing, or is there a way to do it without the tool?

    Also, does anyone have any pointers or final tips before tackling this whole job? Thanks!
    Last edited by Nchristopherson; 08-27-2013 at 07:42 AM.
    Reply With Quote  
     

  2. #2 Re: Doing cam and header build, any tips? 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,815
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    I use a 1/4" 10mm socket and small rubber mallet with some common sense about how hard to hit them to install. FelPro puts an install tool aka piece of plastic that covers the groove for the keepers and then you just lube them up and slide them on.. a quick tap or two and they are done.
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  3. #3 Re: Doing cam and header build, any tips? 
    Turbo is the way to go. REDCRAPGP's Avatar
    Join Date
    Aug 2009
    Location
    Behind you...sike made you look Bish
    Posts
    16,085
    Thanks (Received)
    0
    Likes (Received)
    1
    Dislikes (Received)
    0
    Quote Originally Posted by BillBoost37 View Post
    I use a 1/4" 10mm socket and small rubber mallet with some common sense about how hard to hit them to install. FelPro puts an install tool aka piece of plastic that covers the groove for the keepers and then you just lube them up and slide them on.. a quick tap or two and they are done.
    This! You don't need a special tool for this
    Squirrels are my engine. I need a Ford Regal
    04 Comp G.
    Reply With Quote  
     

  4. #4 Re: Doing cam and header build, any tips? 
    GT Level Member
    Join Date
    Jun 2013
    Location
    Hollywood ,FL
    Posts
    407
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    how did the install go ? how long did it take did you run into any problems?
    Reply With Quote  
     

Similar Threads

  1. Tips before starting cam build
    By WolvesSoulZ in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 8
    Last Post: 08-19-2013, 01:15 PM
  2. Header Install Tips?
    By ImColeTrickle in forum General Tech Discussion
    Replies: 5
    Last Post: 03-08-2012, 09:09 AM
  3. Too Slow, Time for a build (GEN V/N*/L32 Lim build)
    By AmericanSoldier in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 124
    Last Post: 01-13-2012, 01:54 PM
  4. header gasket - header clamps - kn filter
    By homerunhitter629 in forum General Tech Discussion
    Replies: 1
    Last Post: 02-21-2011, 10:00 AM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •