Thread: Aj's CompG build progress thread (car has a new owner!)

Page 7 of 9 FirstFirst ... 56789 LastLast
Results 121 to 140 of 165
  1. #121 Re: Aj's 2013 CompG build progress thread 
    GT Level Member
    Join Date
    Jun 2013
    Location
    Hollywood ,FL
    Posts
    407
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Were u on st tires for a 13.1 I trapped 102 @13.8 are you cammed amd what pulley and intercooler

    Sent from my SGH-T999N using Tapatalk
    Reply With Quote  
     

  2. #122 Re: Aj's 2013 CompG build progress thread 
    GTP Level Member AjL227's Avatar
    Join Date
    Mar 2010
    Location
    IL
    Posts
    701
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    September 2011:::
    -Great Lakes Dragway
    -XP cam, ZZP S2 I/C w/ 3.0" pulley
    -Bald (X<1/32" tread) all season 225/55/17 tires
    -11.4 AFR (E85) / 10 psi / 26* timing advance
    PB = 12.9 @ 110 MPH w/ 2.1 60'

    November 2013:::
    -Byron Dragway
    -XP cam, ZZP S2 I/C w/ 3.0" pulley
    -M/T ET Streets 275/45/17 radials
    -11.4 AFR (E85) / 10-11 psi / 20* timing advance
    PB = 12.9 @ 102 MPH w/ 2.1 60'

    Car started knocking badly every run once in 3rd gear ~92-97 MPH
    Issue was never resolved, I'm thinking it may have just been a bad tank of E85.
    The way the runs were going up until 3rd, I bet I could have had a nice low 12...despite the launch.
    Seeing as my 60' is still a 2.1, I need more practice launching.
    So very anxious for April, you have no idea.
    Last edited by AjL227; 12-24-2013 at 11:52 AM.
    '04 CompG "WS6"
    '00 2.5RS "GM6"
    Reply With Quote  
     

  3. #123 Re: Aj's 2013 CompG build progress thread 
    GTP Level Member AjL227's Avatar
    Join Date
    Mar 2010
    Location
    IL
    Posts
    701
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    If it isn't leaking coolant somewhere, it's preparing to leak out somewhere else.


    The acc. belt is screeching badly time to time and it's really annoying.
    I put some sil-gylde on the belt, and not even 10 minutes of driving later that same mess is back.
    It started overheating later, drove it home and shut it off.
    It was steaming out from around the upper section of the lower rad hose near the SC idler tower. I'm thinking the block drain bolt, but I just freakin' re-sealed that bolt when the trans went in.


    Getting so ****ing tired of this car's ****.
    '04 CompG "WS6"
    '00 2.5RS "GM6"
    Reply With Quote  
     

  4. #124 Re: Aj's 2013 CompG build progress thread 
    GTP Level Member 231FUN's Avatar
    Join Date
    Dec 2011
    Location
    Ontario,Canada
    Posts
    861
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    I'd install a new acc. belt if I were you, I've found once they've been contaminated they just don't seem to be the same again.
    I had a similar issue this summer after dealing with an oil leak at front crank seal after cam install,got motor sealed back up but no matter how much I cleaned the belt or dressed it the thing would still squeal under load. Installed the new Gates "W" quiet belt and it hasn't made a squeak or squeal since.
    Reply With Quote  
     

  5. #125 Re: Aj's 2013 CompG build progress thread 
    GT Level Member
    Join Date
    Jun 2013
    Location
    Hollywood ,FL
    Posts
    407
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Hey what exactly did u buy for the s2 I/c did you upgrade your maf ? I need more power

    Sent from my SGH-T999N using Tapatalk
    Reply With Quote  
     

  6. #126 Re: Aj's 2013 CompG build progress thread 
    GTP Level Member chris99gtp's Avatar
    Join Date
    Jun 2012
    Location
    Illinois
    Posts
    895
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    very nice car man. i'm extremely jealous of it.... where in DuPage are you?
    99 gtp- Burnt and gone
    01 gtp- Here to stay-3.4, SD Headers, AL104's HAI, Overkill PCM, SD Hood
    Reply With Quote  
     

  7. #127 Re: Aj's 2013 CompG build progress thread 
    GTP Level Member AjL227's Avatar
    Join Date
    Mar 2010
    Location
    IL
    Posts
    701
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    I took the SC belt and tensioner off to have a closer look when I drive it shortly.
    That belt screech is torture on the ears especially with the hood popped, then it goes away / charging voltage back up to 14.6v
    '04 CompG "WS6"
    '00 2.5RS "GM6"
    Reply With Quote  
     

  8. #128 Re: Aj's 2013 CompG build progress thread 
    GTP Level Member AjL227's Avatar
    Join Date
    Mar 2010
    Location
    IL
    Posts
    701
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    I filled up the radiator, it was fairly low... drove it about 50 miles today and filled it up with more E85.
    No issues, coolant leaks or screeching belt.
    '04 CompG "WS6"
    '00 2.5RS "GM6"
    Reply With Quote  
     

  9. #129 Re: Aj's 2013 CompG build progress thread 
    GTP Level Member rodguezsciii's Avatar
    Join Date
    Sep 2012
    Location
    19805
    Posts
    722
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    damn I wish there was more than just the one E85 station near me....not sure why, but your car is the first I've ever actually preferred the Inferno lip on....
    Reply With Quote  
     

  10. #130 Re: Aj's 2013 CompG build progress thread 
    GTP Level Member AjL227's Avatar
    Join Date
    Mar 2010
    Location
    IL
    Posts
    701
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    The only thing I like about the SE front fascia is that it clips in like factory.
    I saw a 2004+ GP downtown Chicago with an SLP hood, never seen one in person.
    '04 CompG "WS6"
    '00 2.5RS "GM6"
    Reply With Quote  
     

  11. #131 Re: Aj's 2013 CompG build progress thread 
    GT Level Member
    Join Date
    May 2013
    Location
    illinois
    Posts
    186
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    hows the car start on e85 in the cold, my 04 wouldnt start if it was below freezing on e85
    Reply With Quote  
     

  12. #132 Re: Aj's 2013 CompG build progress thread 
    GTP Level Member AjL227's Avatar
    Join Date
    Mar 2010
    Location
    IL
    Posts
    701
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Car has been the perfect snowplow all day, today.
    Grips hard everywhere.
    Bring on the snow!


    '04 CompG "WS6"
    '00 2.5RS "GM6"
    Reply With Quote  
     

  13. #133 Re: Aj's 2013 CompG build progress thread 
    GTP Level Member AjL227's Avatar
    Join Date
    Mar 2010
    Location
    IL
    Posts
    701
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    I can't sleep, so I went downstairs to the garage and installed the 2nd TRS HID harness/relay & Morimoto ballasts for the fog lights.
    Pictures of the lights and wiring setup soon.
    They look sick!
    jg.gif
    '04 CompG "WS6"
    '00 2.5RS "GM6"
    Reply With Quote  
     

  14. #134 Re: Aj's 2013 CompG build progress thread 
    GT Level Member
    Join Date
    Jun 2013
    Location
    Hollywood ,FL
    Posts
    407
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Can't wait

    Sent from my SGH-T999N using Tapatalk
    Reply With Quote  
     

  15. #135 Re: Aj's 2013 CompG build progress thread 
    GTP Level Member AjL227's Avatar
    Join Date
    Mar 2010
    Location
    IL
    Posts
    701
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    HID fog teaser


    '04 CompG "WS6"
    '00 2.5RS "GM6"
    Reply With Quote  
     

  16. #136 Re: Aj's 2013 CompG build progress thread 
    GTP Level Member AjL227's Avatar
    Join Date
    Mar 2010
    Location
    IL
    Posts
    701
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Car is sold.
    Bought something new.

    Aj's CompG build progress thread (car has a new owner!) Attached Images
    '04 CompG "WS6"
    '00 2.5RS "GM6"
    Reply With Quote  
     

  17. #137 Re: Aj's 2013 CompG build progress thread 
    I live here. DirtDog's Avatar
    Join Date
    Jun 2012
    Location
    Jacksonville, North Carolina, United States
    Posts
    7,750
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    GTFO
    http://www.grandprixforums.net/my-06-gp-gxp-72403.html
    OBX headers, TEP tranny cooler, ls1 IM fuel rails and injectors, ls2 TB, ls7 MAF, full custom exhaust, Quad retro headlights, full out front and rear suspension work, tuned by HPT by me 8====>

    Reply With Quote  
     

  18. #138 Re: Aj's 2013 CompG build progress thread 
    Turbo is the way to go. REDCRAPGP's Avatar
    Join Date
    Aug 2009
    Location
    Behind you...sike made you look Bish
    Posts
    16,085
    Thanks (Received)
    0
    Likes (Received)
    1
    Dislikes (Received)
    0
    Quote Originally Posted by DirtDog View Post
    GTFO
    This
    Squirrels are my engine. I need a Ford Regal
    04 Comp G.
    Reply With Quote  
     

  19. #139 Re: Aj's 2013 CompG build progress thread 
    GrandPrix Junkie spazzz's Avatar
    Join Date
    Nov 2012
    Location
    Madison
    Posts
    3,328
    Thanks (Received)
    3
    Likes (Received)
    8
    Dislikes (Received)
    0
    Sure jell
    Reply With Quote  
     

  20. #140 Re: Aj's 2013 CompG build progress thread 
    GT Level Member
    Join Date
    Jun 2013
    Location
    Hollywood ,FL
    Posts
    407
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Na ur o playing

    Sent from my SGH-T999N using Tapatalk
    Reply With Quote  
     

Page 7 of 9 FirstFirst ... 56789 LastLast

Similar Threads

  1. Spartan GL's Build Thread: (09-21-14) New photos!
    By Spartan GL in forum Members Rides
    Replies: 1226
    Last Post: 01-11-2016, 08:13 PM
  2. My CompG in Progress.
    By FriboRage in forum Members Rides
    Replies: 44
    Last Post: 03-12-2014, 12:38 AM
  3. Build Thread: Addicted to L67's~updated 4/6/2013
    By 88formula in forum Members Rides
    Replies: 271
    Last Post: 04-26-2013, 11:14 PM
  4. Regenesis Build Thread. Jan 2013. Dropping in to say hi!!
    By MRANGRYGTP in forum Members Rides
    Replies: 280
    Last Post: 03-01-2013, 07:20 PM
  5. Replies: 89
    Last Post: 11-20-2012, 11:30 AM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •