Thread: Red 2006 Grand Prix GT Supercharged

Originally Posted by TexasTanker19kilo20

Great score on the STB.

thanks! I seen you wanted everything else from him so I saved it for ya!

Went n cut out with a hole saw. Traced through the projector housing n just cut it till the projector could clear with a little wiggle room!

cant figure out how to tie in my hi beam splitters tho. I hooked them from my projectors into the black and blue but for the black male splitters I don't see how them can hook up into my hi beams?


i don't know what or how to tie the bottom black things into w.e they go to. Any help or pics would be appreciated!
Then I might try n mount n aim them tonight if its not too cold

Yup what's the need for the splitter for?

Originally Posted by REDCOMPG

Yup what's the need for the splitter for?

Trs said I needed them for my highs!! If I dont need them than good, ik how to hook it all up then haha. but then what does the red n black wires from the projector hook up to? Im pm'ing someone n they said it goes to the hi beam splitters like in the picture n then idk where the rest goes..

The projectors are lows and highs n you need the hi beam splitters for that to be possible. If I cant figure it out for now it doesn't matter. I never use my hi beams nor am I in the country too much to even use em lol. But just figured since I got it, if I could hook them up its be better

Em no you don't sir.Just splice and wire them into the factory high beams.

Good work. One day i shall do this.

Originally Posted by REDCOMPG

Em no you don't sir.Just splice and wire them into the factory high beams.

Lol well since I already have them, id like to hook it up w.o splicing wires..any idea? N id splice them into that red n black wire from my projectors?

Originally Posted by TexasTanker19kilo20

Good work. One day i shall do this.

Thanks texas, youll get it done sometime!

The red and black wire is essentially what turns the projectors into the high beam. Just splice into that and the green/black wire coming from where the standard halogens high beams on. Should work for you. That's how I've had mines set up and worked perfectly. Try it. Worse case scenario is you just splice them back.

Originally Posted by REDCOMPG

The red and black wire is essentially what turns the projectors into the high beam. Just splice into that and the green/black wire coming from where the standard halogens high beams on. Should work for you. That's how I've had mines set up and worked perfectly. Try it. Worse case scenario is you just splice them back.

Alright I gotcha then. Just since I had it I didnt know if there was an easier way to hook em up. Cuz as you can see on them splitters, that black male plug doesn't look like itd hook up to anything or is it just me? Lol

Never used the splitter myself and at the time there wasn't much retrofits going around so it required some trial and error and splicing up wires for me to get everything to work. Hey wiring doesn't have to be pretty you don't see it

Lol yeah youre right! Well if I gotta do that I will. I could care less if I even had hi beams! Haha. The splitters were only $10 so I grabbed em n they told me id need em lol. Obviously so I wouldnt have to splice into anything. But the spades on the black park are wider so it wont plug into anything, unless im overlooking something. Ill have to check again later.

Well this is from the projector to the splitter n then the black is supposed to plug into the factory hi beam where I take off the bulb..but these spades arent small like what usually getz plugged in. Theyre about a 1/4 inch wide or so
as you can see theyre wider than the little pins that come out of the projector

Originally Posted by spazzz

I'm not trying to get on your nerves but read this quick. Bi xenon projector wiring 9006

Lol ill check it out, youre not getting on my nerves! All im doing is asking for the help n you all are helping me! I appreciate it but yeah I havent really searched up a wiring diagram or anything yet and you just did for me so thank you! Lol

Took a picture of my lower fascia from what I painted the other day. Turned out good

but anyways! I started to aim my projectors and one of my bulbs are burnt out already! I'm pretty pissed about that and swore quite a few times. Started aiming n putting jb weld n it kept wanting to sag. Snapped a few pics n I held it to where I wanted as I took it out n then filled it in with jb weld when I got inside so hopefully it's still where it was! But wow I'm so mad that one is already eff'ed up n need to email them to see if they'll do anything about it. Annoying.