Thread: DIY: How to polish engine parts

Results 1 to 13 of 13

Threaded View

03GPScottyd DIY: How to polish engine... 08-07-2008, 12:01 PM
GR8racingfool Re: DIY: How to polish engine... 08-07-2008, 01:34 PM
justwhisen Re: DIY: How to polish engine... 08-07-2008, 04:36 PM
GTPJOE90 Re: DIY: How to polish engine... 08-08-2008, 02:02 PM
NickT\'sGTP Re: DIY: How to polish engine... 08-13-2008, 03:38 AM
justwhisen Re: DIY: How to polish engine... 08-13-2008, 08:40 AM
2000GTP Re: DIY: How to polish engine... 08-15-2008, 12:09 AM
03GPScottyd Re: DIY: How to polish engine... 08-15-2008, 01:08 PM
2000GTP Re: DIY: How to polish engine... 08-16-2008, 09:10 PM
TommyGloves Re: DIY: How to polish engine... 08-17-2008, 10:39 PM
stlmo_gtp Re: DIY: How to polish engine... 08-17-2008, 11:34 PM
SDGTP99 Re: DIY: How to polish engine... 07-18-2009, 05:02 PM
chico Re: DIY: How to polish engine... 08-08-2009, 06:05 PM
Previous Post Previous Post   Next Post Next Post
  1. #1 DIY: How to polish engine parts 
    GTP Level Member 03GPScottyd's Avatar
    Join Date
    Dec 2007
    Location
    Louisville, KY
    Posts
    1,260
    Thanks (Received)
    1
    Likes (Received)
    1
    Dislikes (Received)
    0
    First off I would like to say that I got this from SupraForums.com.au and it was written by Solman, but if you plan on using this writeup you have to pay me a finders fee of at least one polished part for my car. I figure if 20 of you use this writeup, my whole engine should be showcar ready within the year.

    Disclaimer: I have not tried to do this but it should be common sense that if you attempt to do this you could remove too much metal and make the part that you are attempting to polish structurally weaker and it could fail in the future if you are not careful when attempting this process.

    DIY: How to polish engine parts:

    This is a guide on how to polish engine parts. An intake manifold is used to show how, but this can be done on just about any metallic engine part (piping, cast aluminum, sheet metals and others)

    Before:


    After:


    Tools require and costs:

    Brown Buffing soap $10 approx
    White buffing soap $10 approx
    Loose buffing wheel $20 approx
    Stitched buffing wheel $20 approx


    Bench grinder $50 - $300 depending on brand
    Adapter for wheel $20 approx


    Angle grinder $50 - $300 depending on brand
    120grit sanding disk $15 approx


    Wet and dry Sand paper:

    2 x 120grit $2
    2 x 240grit $2
    1 x 400grit $1
    1 x 800grit $1
    1 x 1200grit $1
    1 x 2000grit $1

    Disposable gloves $7 approx this is optional just makes it easier to keep hands clean


    Step 1 Tape (Optional):

    Tape up intake manifold to avoid aluminum bits getting inside it while sanding. Still clean it out with degreaser once your done, this just makes it easier to clean afterwards.



    Step 2 Using the angle grinder:

    The manifold is a cast aluminum part so there are lots of “pores” that need removing. Other metal parts may not require this level of sanding as they are relatively smooth all ready.


    Ok some people may be afraid to take an angel grinder to their engine parts, but the sanding disk that is used is fairly fine, so it should be ok as long as you don’t sit there for half an hour on one spot. Apply light even pressure and “brush” it along the part.

    If your really worried skip this step, but if your sanding down cast aluminum like the intake manifold, then either your patient as hell or you will reconsider.


    You want to make sure you remove all the pores!


    After using the grinder you will end up with something like this:



    Step 3 Manual sanding:

    Ok now that the pores are removed we need to smooth out the surface. Use the same grit as the disk here (120grit) to even out the lines and unevenness left by the sanding disk.


    After dry sanding, spray some degreaser and then do a wet sand which gives a better finish.




    This is how it looks after the wet sand:


    Continue doing the same with 240, 400, 800, 1200, and 2000 grit.

    After 400 grit:


    After 800 grit:

    You should be able to see it becoming more reflective.

    After 1200 grit:
    Here you can see the difference between a wet and dry sand (top being wet)


    And Finally after the 2000 grit:



    Step 4 polishing (cutting stage):

    Ok now that the hard part is complete all we have left is to polish the surface. The finish of your product will depend on how much effort you put into your sanding, and the smoother the sanding the better the polish.

    Setup your bench grinder with the tapered tool and the stitched wheel, this wheel is a cutting wheel which “cuts” the material to give it a better finish.


    Use the brown buffing soap with this wheel.


    Take your time and try to work every area. Make sure you reapply more buffing soap on your wheel now and then.

    This is the finish product after the cutting wheel.



    Step 4 polishing (Final polish):

    Ok now change the buffing wheel to the loose buffing wheel. Use the white buffing soap with this wheel to give the metal a better overall finish.


    This is how it should look after this stage:


    Now get out there and polish away.
    Last edited by 03GPScottyd; 08-07-2008 at 12:21 PM.
    debadged, clear corners, 20% tint, tinted tails, vibrant performance tips, red painted calipers, Fig. grills, autometer guages, PFYC 3 pod A pillar, SLP CAI, 2.5" DP, SD Hood, SD front air damn, Gen I spoiler, 17X8 Borbet Type M rims, engine upgrades soon!
    My Cardomain
    Reply With Quote  
     

Similar Threads

  1. INFORMATION Pledge Dusting Polish As A Engine Bay Detailer
    By SyntheticShield in forum Detailing Tips and Tricks
    Replies: 26
    Last Post: 06-29-2009, 06:15 AM
  2. Engine bay detail parts questions...
    By Iron Indian in forum Visual/Body Modifications
    Replies: 2
    Last Post: 07-12-2008, 11:26 PM
  3. New pics of my tint job and painted engine parts
    By ryangtp89 in forum Off Topic Discussion
    Replies: 3
    Last Post: 12-27-2007, 01:15 AM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •