How is this little gadget for reading KR and more ?

**ryangtp89** · 01-07-2014

I found something that can read KR and it shows other stuff too, I like that it shows mph. But under the notes it mentions on the extended options its delayed up to 10 seconds soo its not true real time ? soo that wouldn't be too useful for mph right ?

http://www.fullthrottlespeed.com/ite...CANL67+eq++Tp+

**dsmuts** · 01-07-2014

I had one i sold. I liked it and it was in realtime.

**ryangtp89** · 01-07-2014

ok good! nothing worst than delayed info! i'll pick one up tonight then. Just got done odering everything, hopfully I wont see no KR. I'd like to do the 1.8 yella terra's to completely eliminate the kr but I'll wait this summer. I heard the ported tb and ported s/c is a waste too unless doing a intercooler. I'm just trying to find anything else I can do to eliminate the kr for somewhat cheap. I'd figure the 3.5 was a better choice then the 3.4 and the 3.6 doesn't seem like id gain much.

**Twizted 1** · 01-07-2014

Rockers aren't always going to eliminate KR. Do the mods, check for KR, tune to help KR.

Sent from Not so smart smartphone

**ryangtp89** · 01-07-2014

i'll be getting a mail order tune from either zzp or intense, I'm no good at tunning or even trying to learn, and theres nobody in my state that does it.

**dsmuts** · 01-07-2014

rockers will help with kr. I had 6-8* and put modded 1.9's on and it took care of it.

**ryangtp89** · 01-07-2014

Would it be fine to get the pcm now than do the rockers or should it be tuned for rockers ? I'm going with the 1.8 yella terras if I do. I didn't hear a lot of good stuff about the modded rockers

**dsmuts** · 01-07-2014

I had no problems with my rockers. I got the zzp 1.0 pcm and had more KR than i did on a stock tune so I threw the rockers on to take care of it.

**Twizted 1** · 01-07-2014

I had 6-8Â° without rockers. Installed harland sharp 1.9's and still get 3-4Â° spikes.
Just saying not 1 motor is the same.
Don't depend on rockers solving your problems, scan, tune......

Sent from Not so smart smartphone

**Z34Phoenix** · 01-07-2014

for the price of that you can have an aeroforce gauge or almost buy a used DHP tuner. that thing is not worth it. there is still info floating around to help you learn to tune these cars. get the tuner

**machinegunsquid** · 01-07-2014

I would go with an Intense canned tune over a ZZP.

When I got mine for my setup I got a phone call and spoke with Intense for a good 5 minutes on what mods, driving habits, what I wanted, and just sorta shot the **** for a bit. Plus you can send them a scan-log and they'll retune it for you.

Grab the 3.5 pulley, the 1.8 YT's and the Intense PCM and be a happy camper.

**indygrandprix** · 01-07-2014

if all you wanna do is read KR get the torque app and on your phone and the reader to plug into the obd port. way way cheaper

**ryangtp89** · 01-08-2014

Do i have to/should tune for the rockers when I get the intense mail order tune ? Would it be safe to to have the 1.8 yell as as my first mod ? I can't afford everything at once and I'm having my work (dealership) install them for me soo I don't mind it being in the garage for a few days since I have another vehicle. I just rather have them do the rockers first soo when they put everything back together they don't screw up my cai somehow.

**dmahlikGT** · 01-08-2014

Do rockers first then get the tune based off of all your mods. It will all then flow together.

**ryangtp89** · 01-08-2014

Sounds good. Just didn't know if it will run like **** on the stock pcm. Then I'll do the rockers first than get the basic mods then get the mail order tune when I buy that stuff.

**dsmuts** · 01-08-2014

It'll run fine on a stock tune. Do rockers, headers, pulley drop then tune.

**dsmuts** · 01-08-2014

**ryangtp89** · 01-08-2014

Originally Posted by Z34Phoenix

for the price of that you can have an aeroforce gauge or almost buy a used DHP tuner. that thing is not worth it. there is still info floating around to help you learn to tune these cars. get the tuner

I would get it but I cant find any single column pods for it anywhere! I'm not into the 3 pod a pillar. I would do a 1 pod on the a pillar but on the column would be ideal for me.