|
|
12-10-2009
I have been trying to run an amp power wire for about 2 hours now. I tired running the wire thru a grommet on the drivers side but gave up on that. From what I've read on the forum it's alot easier to run it under the glovebox on the passenger side. I located the grommet under the hood but am not sure where its located in the interior. Is the picture below what I need to slice into in order to feed the wire thru? If not where exactly is this grommet located in the interior? Thanks!
12-10-2009
thats it buddy, you need to take off the plastic trim around the door to get the carpet up then you can see it right under the glovebox.
Three screws, maybe four, but only one plastic piece.
On the engine side of the firewall theres a thin plastic boot you'll need to get through, just poke it with a screwdriver and push it through there.
12-10-2009
or u can feed it through the door
but thats the biggest pain in the ass
12-10-2009
Originally Posted by 02gpgt88
? the door goes into the lower section of the dash.
12-10-2009
i didnt need to unscrew any little plastic piece
just the door trim goin to the backseat/trunk
12-11-2009
i dont see why u couldnt get it through the boot in the firewall. u gotta take a screw driver and stretch that hole :P
12-11-2009
Just make sure you put that rubber thingy back in. Simple as that.
12-11-2009
I just did this last week. Take a needlenose or whatever you can to pull that square plug out. Once thats out take a knife and notch a bigger hole for your power wire to fit through. Then tape a clothes hanger to the wire and push it through that thin boot behind where the plug goes. Then just find it and feed up up away from the belt and your done.
04-24-2010
Sorry to revive the thread, but I'm working on the same project and I was wondering if you could be a little more detailed about where that is, do I have to look under the car because I can't seem to find it! Thanks!
04-24-2010
pull carpet out from under dash area... cant miss it... little black rubber grommet.
Originally Posted by SuperSport
04-24-2010
Its not that little... About 3x2 maybe?
04-24-2010
Yup, refer to the pic i posted...
04-24-2010
Ok thanks I will try it out.
04-27-2010
not trying to get into a pissing contest but I dont understand why u guys would even take the rubber boot out. must be a 97-03 model?
then again it's not that big of a deal soooo...
04-27-2010
It's just big enough to fit the wires that are already going through it. No way you would fit a run of sub wire without notching it out.not trying to get into a pissing contest but I dont understand why u guys would even take the rubber boot out. must be a 97-03 model?
then again it's not that big of a deal soooo...
04-27-2010
I've got two runs of 4 guage and i didn't even bother putting it back in this time... I dont drive through puddles anyways =D
04-27-2010
maybe thats a small 97-03 issue cause my 06, I just jabbed it with a screwdriver and stretched it, took 20 secs.
04-27-2010
Yes yes the grommet itself, i did that too. There is like a rubber plug that goes in that hole too, that is what they are talking about.
04-28-2010
Yes I remember when I had to do this. The rubbed plug is a pain to get out unless you grab it with some plyers. I didn't evenput mine back in and it works just fine without. Took a screw drivers and drove it though the plastic cover on the firewall side and then it was simple as pie to push the wire through from the firewall.
04-28-2010
oooooooooooooooo! I don't remember that part
| « Previous Thread | Next Thread » |
| Tags for this Thread |
| Bookmarks |
Bookmarks |
