Ok guys took my intercooler off and my question is could I use this LIM
or do I need to use my GEN V LIM
Thanks!
Sent from my SAMSUNG-SGH-I747 using Tapatalk
|
|
03-28-2014
Ok guys took my intercooler off and my question is could I use this LIM
or do I need to use my GEN V LIM
Thanks!
Sent from my SAMSUNG-SGH-I747 using Tapatalk
03-28-2014
For best results and less chance for leaks use the Gen V LIM.
03-28-2014
So this wouldn't be a good LIM I just dont want to replace my LiM gaskets they are new they dont have no more than 20 miles on them but I dont want to buy new ones if I don't have to should I use a l32 gasket or just RTV the blower onto the LIM?
Sent from my SAMSUNG-SGH-I747 using Tapatalk
03-28-2014
You can reuse them if they're the metal ones...I've seen a done multiple times without failure.
03-28-2014
Ok thanks i'll reuse them again.. would u rtv or use a gasket?
Sent from my SAMSUNG-SGH-I747 using Tapatalk
03-28-2014
The only thing that gets RTV is the corners where the LIM gaskets meet the rubber valley gaskets and that's only a dab.
03-28-2014
I've heard people rtv the blower to the LIM I couldnt use that?Originally Posted by Sven The Sexman
Sent from my SAMSUNG-SGH-I747 using Tapatalk
03-28-2014
You could RTV the blower to the LIM if you'd like. I've done it and it works.
03-28-2014
Just make sure the opening is up to a gen v. Since the outlet is further up on it. That's if you had it set up with a gen 3 before. Use rtv on the corners only I have reused the metal gaskets many times before. You can also add a thin layer of rtv on the bottom and upper part of the gasket. I do it all the time. And if I ever remove it I just take it off with a razor
03-28-2014
Thanks bro anybody got a pic on how they rtv'd the LIM? Thanks it would really help
Sent from my SAMSUNG-SGH-I747 using Tapatalk
03-30-2014
Anybody? Any spots to watch? How did you guys rtv the o rings and pcv or should I just say f it and get the gasket?
Sent from my SAMSUNG-SGH-I747 using Tapatalk
03-30-2014
Gasket is like $12
03-31-2014
Only thing I'd be concerned with is the pcv groove that is cut into the LIM.
If you are looking for a Gen V lim, I have a Gen 3 I modded to Gen V sizing with ported runners and plugged coolant ports. Happened to find it cleaning the garage last week.
03-31-2014
Where is this gasket located at? All the gaskets for the Gen v blower ive seen are 32$ and up do you mean the Gen 3
Bill I have a Gen 3 LIM cut to fit the Gen v should this be good?
you said the pcv groove the hole right below the lim correct?
Sent from my SAMSUNG-SGH-I747 using Tapatalk
03-31-2014
If you look at the pic in the first post. On the lower left of the LIM is a groove, it's for the pcv with the IC. That is all I'd be worried about. Meanwhile..if you clean up that black LIM, we'dl let you use it.
03-31-2014
Take off all the paint up top. You can use a gen 3 gasket and cut it up but I wouldn't suggested for you just get a gen v sc gasket
03-31-2014
Billboost37 check your pm
Sent from my SAMSUNG-SGH-I747 using Tapatalk
03-31-2014
Checked.. nothing there
03-31-2014
Check again lol phone had issues
Sent from my SAMSUNG-SGH-I747 using Tapatalk
03-31-2014
I'd bet your phone isn't making any brownie points with you today.. still nada
| « Previous Thread | Next Thread » |
| Bookmarks |
Bookmarks |
