Thread: Code Overload

Results 1 to 19 of 19

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1 Code Overload 
    SE Level Member Pogo D Klown's Avatar
    Join Date
    Sep 2009
    Location
    Sioux Falls
    Posts
    38
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    So I've been fighting with my 99 gtp for a while now, just replaced the tps and tried cleaning the maf sensor because I was pulling up the codes for them. Everything was starting to look up. Then as I'm heading down the interstate suddenly my rpm's jump up to about 5grand, car starts acting like it doesn't know what gear to go into, couldn't get it past third gear, pulled over and it idles at about 2,000 rpm. And these are the codes I got after this occurance P0101 out of range, P0102 signal low, P0121 TP sensor or APP sensor 1, P0730 Incorrect gear, and P1810 trans pressure switch manifold fault. I need it straight, how F'd am I?
    Reply With Quote  
     

  2. #2 Re: Code Overload 
    GTX Level Member a98gtp4u's Avatar
    Join Date
    Sep 2009
    Location
    GEORGIA
    Posts
    857
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    wow! never heard of that happening. that really sucks man.
    Reply With Quote  
     

  3. #3 Re: Code Overload 
    SE Level Member Pogo D Klown's Avatar
    Join Date
    Sep 2009
    Location
    Sioux Falls
    Posts
    38
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    IT BLOWS! I don't know what to do. Fix it or not even waste my time and just see how much I could get selling it
    Reply With Quote  
     

  4. #4 Re: Code Overload 
    GTX Level Member a98gtp4u's Avatar
    Join Date
    Sep 2009
    Location
    GEORGIA
    Posts
    857
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    well my suggestion is take it somewhere and have a real machine diagnose the problem, not just a code reader. alot of times when 1 sensor goes bad its starts to trigger a bunch of other sensors that r fine 2 set off a code cause they work together. get it checked out my friend, you'd be surprised, its prob something simple and stupid.
    Reply With Quote  
     

  5. #5 Re: Code Overload 
    SE Level Member Pogo D Klown's Avatar
    Join Date
    Sep 2009
    Location
    Sioux Falls
    Posts
    38
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    I'm hope'n so. It'll be in the shop asap 2moro
    Reply With Quote  
     

  6. #6 Re: Code Overload 
    GTX Level Member a98gtp4u's Avatar
    Join Date
    Sep 2009
    Location
    GEORGIA
    Posts
    857
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    thats prob what it is, 1 sensor triggering a bunch of others. or the next thing it could be is the pcm. is your car stock?
    Reply With Quote  
     

  7. #7 Re: Code Overload 
    SE Level Member Pogo D Klown's Avatar
    Join Date
    Sep 2009
    Location
    Sioux Falls
    Posts
    38
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Yes it's all stock. Everything started with the Maf sensor, that caused the tps to go out of whack, and it's just gotten more worse as each day goes by.
    Reply With Quote  
     

  8. #8 Re: Code Overload 
    SE Level Member Pogo D Klown's Avatar
    Join Date
    Sep 2009
    Location
    Sioux Falls
    Posts
    38
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    scratch that..it all happened after my coolant elbows went out and it ran kind of hot. It almost went into the red but I clicked on the heat as soon as i seen the temp jump up and that broght it back down so I don't think a cracked anything, but I'm wondering if i didn't just cook the stank out of it
    Reply With Quote  
     

  9. #9 Re: Code Overload 
    SE Level Member Pogo D Klown's Avatar
    Join Date
    Sep 2009
    Location
    Sioux Falls
    Posts
    38
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Whats the pcm again?
    Reply With Quote  
     

  10. #10 Re: Code Overload 
    Donating Users bbptech's Avatar
    Join Date
    Jun 2008
    Location
    Box Elder, South Dakota
    Posts
    747
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    your pcm is the computer of the car.
    ZZP 10.4mm's, ZZP S2 IC, 3.4, 3.0, Ported Gen V, ZZP Headers, ZZP CNC Heads, ZZP 78mm TB, ZZP Aluminum Valve Covers, Meziere Electric WP, ZZP Fuel Pump, ZZP Fuel Logs, 65 Mototrons, 3.29's, 2500 Stall. Tuned by GLANZERGTX and Kyle. E85 Converted, 21* Timing
    Reply With Quote  
     

  11. #11 Re: Code Overload 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,815
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    Those first few codes point to a TPS issue. You mentilon changing it. I'd be checking it.

    TPS has a lot to do with idle and trans shifting. Get the first issue worked on and see if the trans clears up.
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  12. #12 Re: Code Overload 
    SE Level Member Xhondaguy's Avatar
    Join Date
    May 2008
    Location
    chicagoland
    Posts
    42
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Haha that sounds like a good old Pontiac
    We have all had the situation and it usually turns out to be something very simple
    Reply With Quote  
     

  13. #13 Re: Code Overload 
    GTX Level Member a98gtp4u's Avatar
    Join Date
    Sep 2009
    Location
    GEORGIA
    Posts
    857
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    sounds about rite.
    Reply With Quote  
     

  14. #14 Re: Code Overload 
    SE Level Member Pogo D Klown's Avatar
    Join Date
    Sep 2009
    Location
    Sioux Falls
    Posts
    38
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Oh my god! found the problem, it was right there in my face and I never noticed it. One of the vacuum line T's for the fuel pressure regulator was cracked. runs like a champ again
    Reply With Quote  
     

  15. #15 Re: Code Overload 
    SE Level Member
    Join Date
    Jul 2009
    Location
    land o lakes FL
    Posts
    28
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    check you catalytic converter as crazy as that sounds. i had just about the same problem and i was about to buy a tranny. but it was just a bad cat. good luck
    Reply With Quote  
     

  16. #16 Re: Code Overload 
    SE Level Member
    Join Date
    Sep 2009
    Location
    oak harbor wa
    Posts
    1
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    gratz man. im so glad you fixed your car. i knew it was going to be something really dumb and stupid and right in your face!
    Reply With Quote  
     

  17. #17 Re: Code Overload 
    SE Level Member Pogo D Klown's Avatar
    Join Date
    Sep 2009
    Location
    Sioux Falls
    Posts
    38
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    glad it's done with. For now anyways. I'm still not up to my peak gas mileage like I was. I think I scortched the intake manifold about a month ago when it ran hot. Running like a truck right now, getting about 17.3 miles to the gal
    Reply With Quote  
     

  18. #18 Re: Code Overload 
    Donating Users bbptech's Avatar
    Join Date
    Jun 2008
    Location
    Box Elder, South Dakota
    Posts
    747
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Sioux Falls, SD????
    ZZP 10.4mm's, ZZP S2 IC, 3.4, 3.0, Ported Gen V, ZZP Headers, ZZP CNC Heads, ZZP 78mm TB, ZZP Aluminum Valve Covers, Meziere Electric WP, ZZP Fuel Pump, ZZP Fuel Logs, 65 Mototrons, 3.29's, 2500 Stall. Tuned by GLANZERGTX and Kyle. E85 Converted, 21* Timing
    Reply With Quote  
     

  19. #19 Re: Code Overload 
    SE Level Member Pogo D Klown's Avatar
    Join Date
    Sep 2009
    Location
    Sioux Falls
    Posts
    38
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    yep smack dab in the middle of "ain't **** to do!" ever heard of it?!
    Reply With Quote  
     

Similar Threads

  1. Code p0304
    By gandprixgtpsuper in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 5
    Last Post: 06-09-2011, 08:24 AM
  2. does anyone know how to fix this code?
    By shsfootball57 in forum 3.8L V6 Naturally Aspirated (L36)(L26)
    Replies: 14
    Last Post: 01-22-2011, 12:33 PM
  3. I got a code!!!???
    By justwhisen in forum General Tech Discussion
    Replies: 9
    Last Post: 04-14-2010, 07:22 PM
  4. Trans Code
    By 98GTPON22s in forum 1997-2007 4 speed Automatic (4T65E) (4T65E-HD)
    Replies: 2
    Last Post: 02-17-2009, 08:06 PM
  5. code...
    By gotboost3 in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 2
    Last Post: 01-04-2009, 12:22 AM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •