Thread: Built 4t65e - The results are in.

Page 1 of 12 12311 ... LastLast
Results 1 to 20 of 238
  1. #1 Built 4t65e - The results are in. 
    Solving problems BrandonHall10's Avatar
    Join Date
    Mar 2014
    Location
    Tucson
    Posts
    3,182
    Thanks (Received)
    10
    Likes (Received)
    146
    Dislikes (Received)
    3
    Edit:

    Now that it's complete, here's the full build sheet:

    Master rebuild kit
    -New BW frictions, Raybestos steels, seals, gaskets, and filter
    PNH JTFM Torque convertor (Stock repalcement)
    Bonded separator plate
    Torlon check balls
    Oversize 2nd steel plates x2
    Molded 2nd apply piston
    Sonnax 3rd clutch piston kit (984965-01k)
    TEP reconditioned reaction carrier
    TEP reconditioned input piston
    300m iput shaft
    7/8" 2.93 ratio sprockets
    Borg warner PCS
    Borg warner TCCS
    Shift solenoid x2
    Superior AFL valve repair kit
    Superior valve body kit
    Sonnax TCC relief valve
    Sonnax lube tube clamp
    Trans-go shift kit
    Hardened 4th clutch hub
    ZZP aluminum pan (With improved steel threads)
    New 2-1 coast band
    New 7/8" Hy-Vo chain
    New 1-2 Sonnax shift valve
    New accumulator pistons
    New bushings (All of them)
    New thrust washers
    New Lube dam
    New magnets
    New drive sprocket bearing

    "Mods" Include:
    Modified shift kit spring arrangement
    Enlarged separator plate feed holes
    Tightened 2nd clutch pack
    Tightened 3rd clutch pack
    5 Friction input clutch

    See post #232 for it's real world review.



    Begin original post:

    This fall/winter, I'm planning on building a transmission for my car.

    Here's what I'm planning on using for parts:
    PNH Torque convertor
    Master rebuild kit
    -New frictions, steels, seals, gaskets, and filter
    All bands
    Bonded spacer plate
    Torlon check balls
    Oversize 2nd steel plates x2
    Molded 2nd apply piston
    Molded 3rd apply piston
    TEP reconditioned reaction carrier - Original is out of spec
    300m iput shaft
    7/8" 2.93 single chain set
    Borg warner PCS
    Borg warner TCCS
    AC Delco shift solenoid x2
    Superior AFL valve repair kit
    Superior valve body kit
    Sonnax TCC relief valve
    Trans-go shift kit
    Dorman pan w/ drain plug - Junkyard poked the original
    Hardened 4th clutch hub
    Differential lube tube clamp
    Lube dam
    Round magnet

    Here's the "mods" I plan to do:
    Tightened 2nd clutch pack
    Tightened 3rd clutch pack
    Convert to internal cooler check ball

    Here's what I'm debating:
    Bushings - Not seeing any substantial wear on the originals
    Drive sprocket bearing - Feels tight, but I'm told it's a common failure (?)
    Bonded sonnax 3rd apply piston - Because I'm right there

    The core transmission was pulled from a smashed junkyard '02 Regal with an unknown history. The only thing I know for sure is, 4th gear was gone (based on the completely absent splines on the 4th hub). No chunks in the pan, average amount of sludge on the magnet. Fluid looked.... average for a Tucson w-body. No burned or scarred internals.

    This setup is probably overkill for my current, or even future mods, but here's my though process: I'm going to pull and shelf my current stock, working transmission. Install the built trans and roll on that until I eventually move on from this car. At that point, I'll re-install the stock trans and sell the built trans as a low mile working unit. Hopefully for what I have into it.

    For what it's worth, I have all the time in the world to do this build. No rush on anything. I also have HP tuners, so I can make adjustments in the PCM to take advantage of all the improvements in this build.

    So what do you guys think? Is it a solid plan? What are your thoughts on the pieces I'm debating?
    Last edited by BrandonHall10; 07-20-2016 at 12:13 PM. Reason: Title change
    Reply With Quote  
     

  2. #2 Re: Fall transmission build - Opinions welcomed 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,815
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    Sounds pretty good to me.
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  3. #3 Re: Fall transmission build - Opinions welcomed 
    Solving problems BrandonHall10's Avatar
    Join Date
    Mar 2014
    Location
    Tucson
    Posts
    3,182
    Thanks (Received)
    10
    Likes (Received)
    146
    Dislikes (Received)
    3
    Quote Originally Posted by BillBoost37 View Post
    Sounds pretty good to me.
    Thanks Bill! What are your thoughts on replacing the bushings? Old ones don't show any odd or excessive wear.
    Reply With Quote  
     

  4. #4 Re: Fall transmission build - Opinions welcomed 
    Donating Users GMR Badass's Avatar
    Join Date
    Apr 2011
    Location
    Columbus, OH
    Posts
    879
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Quote Originally Posted by BrandonHall10 View Post
    Thanks Bill! What are your thoughts on replacing the bushings? Old ones don't show any odd or excessive wear.
    If the bushings look good don't worry about them. Caged needle bearing in the stator support I always replace because it is a very common failure.
    1999 GTP 2dr - Whipple 537whp.....for now
    1998 GTP 4dr - ST2, Cartuning PT61, IC - SOLD
    1999 GTP 2dr - SIX, GenV, Headers, TEP Trans, E85 - SOLD
    1997 GTP 4dr - 3.4, 1.9's, 3" DP, P-log - SOLD
    Reply With Quote  
     

  5. #5 Re: Fall transmission build - Opinions welcomed 
    GrandPrix Junkie CrazyGuy03's Avatar
    Join Date
    Jan 2010
    Location
    Buffalo
    Posts
    3,868
    Thanks (Received)
    0
    Likes (Received)
    2
    Dislikes (Received)
    0
    If everything else is overkill, why not replace them anyways ?
    2003 Buick Regal GSX lots of mods - click here to see latest build - http://www.grandprixforums.net/threa...ld-for-the-gsx

    *For Reference - Does not have a Zack Howard Cam - It's an Intense Stage 3 - Thank You*
    Reply With Quote  
     

  6. #6 Re: Fall transmission build - Opinions welcomed 
    GrandPrix Junkie CrazyGuy03's Avatar
    Join Date
    Jan 2010
    Location
    Buffalo
    Posts
    3,868
    Thanks (Received)
    0
    Likes (Received)
    2
    Dislikes (Received)
    0
    Quote Originally Posted by GMR Badass View Post
    If the bushings look good don't worry about them. Caged needle bearing in the stator support I always replace because it is a very common failure.
    I think this is the part that always seems to broken for me on my first couple of builds
    2003 Buick Regal GSX lots of mods - click here to see latest build - http://www.grandprixforums.net/threa...ld-for-the-gsx

    *For Reference - Does not have a Zack Howard Cam - It's an Intense Stage 3 - Thank You*
    Reply With Quote  
     

  7. #7 Re: Fall transmission build - Opinions welcomed 
    Solving problems BrandonHall10's Avatar
    Join Date
    Mar 2014
    Location
    Tucson
    Posts
    3,182
    Thanks (Received)
    10
    Likes (Received)
    146
    Dislikes (Received)
    3
    Quote Originally Posted by GMR Badass View Post
    If the bushings look good don't worry about them. Caged needle bearing in the stator support I always replace because it is a very common failure.
    Is there a way to get the old one out without having the special Kent Moore tool? How do you remove it?

    Quote Originally Posted by CrazyBob03 View Post
    If everything else is overkill, why not replace them anyways ?
    Only because I've never replaced them before. I don't know what kind of tooling it would take. Ebay bushing/bearing puller and Harbor Freight arbor press?
    Reply With Quote  
     

  8. #8 Re: Fall transmission build - Opinions welcomed 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,815
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    Pull the TC seal and the 3-4 torx screws are right there. Poof.. done.
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  9. #9 Re: Fall transmission build - Opinions welcomed 
    Solving problems BrandonHall10's Avatar
    Join Date
    Mar 2014
    Location
    Tucson
    Posts
    3,182
    Thanks (Received)
    10
    Likes (Received)
    146
    Dislikes (Received)
    3
    I guess I don't understand Bill. That gets the stator support out of the case, but I still need to get the bearing out of the stator support.
    Reply With Quote  
     

  10. #10 Re: Fall transmission build - Opinions welcomed 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,815
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    It's one piece when you buy the new one.
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  11. #11 Re: Fall transmission build - Opinions welcomed 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,815
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    at least I'm remembering it as one piece. Unless I just pulled the bearing and replaced it.
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  12. #12 Re: Fall transmission build - Opinions welcomed 
    Solving problems BrandonHall10's Avatar
    Join Date
    Mar 2014
    Location
    Tucson
    Posts
    3,182
    Thanks (Received)
    10
    Likes (Received)
    146
    Dislikes (Received)
    3
    Yeah. Definitely 2 pieces. Caged bearing is pressed into the stator support.

    Reply With Quote  
     

  13. #13 Re: Fall transmission build - Opinions welcomed 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,815
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    I used something else to get it out.. Might own that tool now. Wanna buy more 4T65 tools?
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  14. #14 Re: Fall transmission build - Opinions welcomed 
    Solving problems BrandonHall10's Avatar
    Join Date
    Mar 2014
    Location
    Tucson
    Posts
    3,182
    Thanks (Received)
    10
    Likes (Received)
    146
    Dislikes (Received)
    3
    Quote Originally Posted by BillBoost37 View Post
    Wanna buy more 4T65 tools?
    I'm always looking. You got something to get that bearing out?
    Reply With Quote  
     

  15. #15 Re: Fall transmission build - Opinions welcomed 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,815
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    I might have that actual tool... I'll look and pm you
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  16. #16 Re: Fall transmission build - Opinions welcomed 
    Solving problems BrandonHall10's Avatar
    Join Date
    Mar 2014
    Location
    Tucson
    Posts
    3,182
    Thanks (Received)
    10
    Likes (Received)
    146
    Dislikes (Received)
    3
    Pass the torch Bill!
    Reply With Quote  
     

  17. #17 Re: Fall transmission build - Opinions welcomed 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,815
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    text me your number... cause everyone already has mine
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  18. #18 Re: Fall transmission build - Opinions welcomed 
    Solving problems BrandonHall10's Avatar
    Join Date
    Mar 2014
    Location
    Tucson
    Posts
    3,182
    Thanks (Received)
    10
    Likes (Received)
    146
    Dislikes (Received)
    3
    Sent a PM. I guess I'm one of the few who doesn't have your number.
    Reply With Quote  
     

  19. #19 Re: Fall transmission build - Opinions welcomed 
    SE Level Member
    Join Date
    Apr 2015
    Location
    NJ
    Posts
    140
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    I don't recommend the PNH torque converter at all. While mine hasnt failed or had any issues to speak of, its very, very loose, which makes it horrific on the LS4. My gas mileage dropped to 12.8mpg on this converter as it constantly has to rev to about 2500rpm to accelerate at any good clip. It stalls around 2800 and flashs just above 3k, while it may be ideal for the cam I have, it makes the car feel like a tug boat in the low end. I've spoken with dave at TEP about this and he said its typical of the reman JTFM converters, as they are built around the GTP's 3800 v6. I also spoke with several LS cam mfg'ers and they all recommend getting a custom converter like a circle d, which said they would be more then happy to do the 4t65e. It would be much tighter around town and you could still probably get the stall you wanted without having to worry about it feeling "loose". I'm looking at doing this in a few months and having it swapped out.
    Reply With Quote  
     

  20. #20 Re: Fall transmission build - Opinions welcomed 
    Donating Users GMR Badass's Avatar
    Join Date
    Apr 2011
    Location
    Columbus, OH
    Posts
    879
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Get a PI reman converter through Dave at TEP. I'm like stock stall speed or even lower. 500whp+ Whipple car is running a 2500 stall.
    1999 GTP 2dr - Whipple 537whp.....for now
    1998 GTP 4dr - ST2, Cartuning PT61, IC - SOLD
    1999 GTP 2dr - SIX, GenV, Headers, TEP Trans, E85 - SOLD
    1997 GTP 4dr - 3.4, 1.9's, 3" DP, P-log - SOLD
    Reply With Quote  
     

Page 1 of 12 12311 ... LastLast

Similar Threads

  1. A Stray cat ripped open my screen and welcomed himself into my home
    By acidcrashdburnd in forum Off Topic Discussion
    Replies: 7
    Last Post: 06-13-2012, 08:48 AM
  2. Taz's Offical Summer/Fall build list.
    By Taz Magister in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 321
    Last Post: 12-13-2011, 01:23 PM
  3. my build, need opinions
    By nascartech in forum General Tech Discussion
    Replies: 6
    Last Post: 10-03-2011, 10:53 PM
  4. ScreamsOfTheSouth Build / Need Opinions
    By z3r0 in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 21
    Last Post: 07-22-2011, 10:24 AM
  5. Lookin for opinions here.. Engine build
    By TorqueAutoMotiv in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 2
    Last Post: 06-19-2009, 08:11 AM
Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •