Springs loose?

**jayroca** · 07-05-2015

Originally Posted by BillBoost37

Tyler.. I'm just joking around about the IC stuff. Because you hate IC's so much.

Jay..I apologize man. Whole heartedly, your question was if the spring could be reused and the answer to the question is that I would reuse that spring. The spring itself apears to be perfectly good.

As for reusing a HG, I would never suggest doing so.

As for not hearing or feeling it, I truly can not believe that you could not tell by how it was running. Dude it was running on 5 cylinders based on the picture of the spark plug.

No need to..when in doubt blame tyler lmao!!!!

Originally Posted by 98bleedingaholevet

intercoolers suck that is all carry on people...... nothing to see here!

ohh and e85 all the things!!!! FTW lol

I was 2sec to buying a fs core too!! Isnt that great!!! Lmao

**16MustangVet** · 07-06-2015

sorry man i doubt an intercooler would have saved this....... tune and some e85 on the other hand! lol...........

**BillBoost37** · 07-10-2015

Jay, I was browsing pictures and came across these that might interest you.

These are the types of pics (typical) that led us to think your piston was hosed.

A slightly beat up cylinder head

The piston (or lack of) that was under it.

No worries though..the piston was located

When something bounces around ... things get ugly fast.

**J57ltr** · 07-10-2015

I was going to ask if they were hypereutectic... but I don't think I need to now. Unbereaveable....

**jayroca** · 07-10-2015

Got a new motor already dropped in.. So thats that.. Not playing doctor with my car..the heads werent cleared to match the xpz cam machine shop confirmed this yesterday.. Was told they were for the cam when i purchased them smh ... You live and learn and issues happen head gasket was f**ked coolant spewing out smh..piston wasnt nowhere like that bill no reason to not own up to my **** i babied this motor but sh** wasnt right because of misinformation.. when my new heads come from the machine shop i drop those in along with the 130 springs and go back to my build..

**bandook** · 07-10-2015

I'd still like to see a picture of that piston. Just out of curiosity.

**BillBoost37** · 07-10-2015

Damn dude, sucks to be told stuff is what it isn't. Sorry to hear that.

If you go forward on heads in the future, i had found this tidbit that most don't appear to notice. Our heads, even after being "setup properly" by vendors typically aren't 100% correct. We use LS springs that require an install height of 1.800", modded retainers only give us 1.78X" ....therefore the spring seats should be machined to ensure all aspects (spring height to specs of springs being used, valve guide machined to accomodate expected lift plus seal plus a little insurance space) are good. I think I got lucky that I wanted the shop to check stuff and they noticed the seats.

**REDCRAPGP** · 07-10-2015

Damn that sux

Sent from my iPhone using Tapatalk

**jayroca** · 07-10-2015

Originally Posted by BillBoost37

Damn dude, sucks to be told stuff is what it isn't. Sorry to hear that.

If you go forward on heads in the future, i had found this tidbit that most don't appear to notice. Our heads, even after being "setup properly" by vendors typically aren't 100% correct. We use LS springs that require an install height of 1.800", modded retainers only give us 1.78X" ....therefore the spring seats should be machined to ensure all aspects (spring height to specs of springs being used, valve guide machined to accomodate expected lift plus seal plus a little insurance space) are good. I think I got lucky that I wanted the shop to check stuff and they noticed the seats.

Funni thing is when i brought the heads to the shop.. The machine laughed and said no way in hell those are cleared for over 600. Lift by just looking at them .. Showed me some heads he just finished porting (aluminium by the way).... And made me wish i had never grabbed the heads i had smh..they are ported... he spoke but not to the intent to compliment the cam after i showed him the cam specs..

**BillBoost37** · 07-10-2015

I would want to see a measurement before discounting the actual lift possible.

FWIW these were measured well north of 620 lift

**jayroca** · 07-10-2015

With that build bill what type of cam was used if you dont mind me asking?

**16MustangVet** · 07-10-2015

Just when I was about to loose faith LOL....... Sounds like you did a good job getting down to what caused it to go KABOOM. Hmm wonder if those heads were to blame for the other destroyed engines?

Good to head things are going back together and no matter what Im still jealous of all you bastards at home that get to actually work on their cars while Im overseas! FML!

Edit I believe that setup is S1X cam with 1.8 rockers.

**jayroca** · 07-10-2015

Originally Posted by 98bleedingaholevet

Just when I was about to loose faith LOL....... Sounds like you did a good job getting down to what caused it to go KABOOM. Hmm wonder if those heads were to blame for the other destroyed engines?

Good to head things are going back together and no matter what Im still jealous of all you bastards at home that get to actually work on their cars while Im overseas! FML!

Edit I believe that setup is S1X cam with 1.8 rockers.

Exactly used the same heads on my e85 XP cam with 130 springs... So for right now.. Im gonna just be like u ..lol stock heads XP 130# E85 and Gen V on a guess what........

2.8 pulley lol

**16MustangVet** · 07-10-2015

I hope to god you put like a 3.0 or something on until you get a real fvcking tune! Enough with this can tune nonsense !!!!! Your engine will thank you..........