Thread: E85 startup tuning???

Page 2 of 3 FirstFirst 123 LastLast
Results 21 to 40 of 47
  1. #21 Re: E85 startup tuning??? 
    GTP Level Member
    Join Date
    Jun 2016
    Location
    Cleveland ohio
    Posts
    890
    Thanks (Received)
    1
    Likes (Received)
    9
    Dislikes (Received)
    0
    They are stills staying pegged. I don't see a vacuum leak that would cause this. Looks like I will just run out the e85 fuel and then strip it all down. ill keep the e85 fuel pump the the rest goes.
    2017 Buick Regal 2.0 Turbo (SOLD 2007 Grand Prix GT. Front and rear PLOGs, 1.8 roller rockers, CAI, HPTuned, 3.4 pulley, TEP transmission, 90# springs, rollmaster single chain, Impala front brakes d/s rotors.) Past (Pontiacs) Grand Prix- 97 GT, 03 GT, 04 GT, 04 Comp G, 78 Trans am, 92 Trans Am.
    Reply With Quote  
     

  2. #22 Re: E85 startup tuning??? 
    GTP Level Member
    Join Date
    Jun 2016
    Location
    Cleveland ohio
    Posts
    890
    Thanks (Received)
    1
    Likes (Received)
    9
    Dislikes (Received)
    0
    Should I just leave the 3.0 pulley and belt wrap kit on there when I take everything back off. It will be a normal GTP with some mods in my signature along with a Meth kit. Or should I swap the 3.0 out for the 3.25?
    Reply With Quote  
     

  3. #23 Re: E85 startup tuning??? 
    GXP Level Member GTPpower's Avatar
    Join Date
    May 2008
    Location
    Schuyler, NE
    Posts
    2,972
    Thanks (Received)
    8
    Likes (Received)
    23
    Dislikes (Received)
    0
    You should put a stock pulley back on. Maybe a 3.4 if you'll stay on top with the meth.
    Reply With Quote  
     

  4. #24 Re: E85 startup tuning??? 
    GTP Level Member
    Join Date
    Jun 2016
    Location
    Cleveland ohio
    Posts
    890
    Thanks (Received)
    1
    Likes (Received)
    9
    Dislikes (Received)
    0
    Ohh geez. Thanks. I roll a lot smaller than I should. 3.25 is back on there right now. That’s what I ran before all this. It ran well without much knock at all. I will definitely pay close attention and put the 3.4 on if I have too!! Thanks bro!!
    Reply With Quote  
     

  5. #25 Re: E85 startup tuning??? 
    GTP Level Member
    Join Date
    Jun 2016
    Location
    Cleveland ohio
    Posts
    890
    Thanks (Received)
    1
    Likes (Received)
    9
    Dislikes (Received)
    0
    S*%t now the dreaded P0171. I see no leaks anywhere! I’m ready to blow this damn car up.
    Reply With Quote  
     

  6. #26 Re: E85 startup tuning??? 
    GXP Level Member GTPpower's Avatar
    Join Date
    May 2008
    Location
    Schuyler, NE
    Posts
    2,972
    Thanks (Received)
    8
    Likes (Received)
    23
    Dislikes (Received)
    0
    I would bet money you have vacuum leak.
    Reply With Quote  
     

  7. #27 Re: E85 startup tuning??? 
    Donating Users bandook's Avatar
    Join Date
    Apr 2015
    Location
    Columbus, OH
    Posts
    1,781
    Thanks (Received)
    2
    Likes (Received)
    27
    Dislikes (Received)
    0
    Quote Originally Posted by rickisrad View Post
    Ill contact ZZP to see if they have the file. One thing I was looking at my LTFT from my last scan and they were positive. Most +16. Which is very lean. Can someone please link how to change that with HPT. I've had brain procedures the last 4 weeks so I have a hard time remembering anything. Any help is appreciated.
    You don't know how to adjust your MAF? Are you tuning just by fuel trims, or do you have wideband? Exactly what process are you using to adjust fuel? Come down to Columbus, I'll help. Don't throw in the towel when u are frustrated, your probably just overlooking something.
    Top Swapped 01 Imp
    VS (very small?) cam, SD Headers, 2.8" pulley, 29°, ported everything, E85, AEM water/meth, Deka 60's, HPT tuned
    Reply With Quote  
     

  8. #28 Re: E85 startup tuning??? 
    GTP Level Member
    Join Date
    Jun 2016
    Location
    Cleveland ohio
    Posts
    890
    Thanks (Received)
    1
    Likes (Received)
    9
    Dislikes (Received)
    0
    I can’t find a vacuum leak. I used water with a bit of methanol in it to spray around and nothing. I took the oil cap off and it didn’t seem to have vacuum. I’m going to have to find somewhere with smoke to find the leak when I get the money.

    bandook- I figured out what I was looking for I believe. I have a lot of memory loss from brain procedures I went through very recently. If I had money I would take you up on your offer in a heartbeat.
    Reply With Quote  
     

  9. #29 Re: E85 startup tuning??? 
    GTP Level Member
    Join Date
    Jun 2016
    Location
    Cleveland ohio
    Posts
    890
    Thanks (Received)
    1
    Likes (Received)
    9
    Dislikes (Received)
    0
    I think this is the same issue that caused me to come back from e85!!

    I used propane and cigar and no leak noticed.

    After a lot of research I think it’s either the MAF or more than likely the o2 sensor. I’m thinking the o2 originally was damaged from the e85.
    Reply With Quote  
     

  10. #30 Re: E85 startup tuning??? 
    GXP Level Member GTPpower's Avatar
    Join Date
    May 2008
    Location
    Schuyler, NE
    Posts
    2,972
    Thanks (Received)
    8
    Likes (Received)
    23
    Dislikes (Received)
    0
    E85 won't damage an O2 sensor. But it could be a bad sensor. Scan O2 mv and you'll see what it's doing. It should be oscillating rapidly. It may not be though since you have 16.4+ ltft.
    Reply With Quote  
     

  11. #31 Re: E85 startup tuning??? 
    GTP Level Member
    Join Date
    Jun 2016
    Location
    Cleveland ohio
    Posts
    890
    Thanks (Received)
    1
    Likes (Received)
    9
    Dislikes (Received)
    0
    This site will not me upload a scan.

    The o2 sensor has movement but doesn't seem like as much as normal but close. On the scan the LTFT was pegged at 16.4 most of the time. This is really throwing me for a loop.
    2017 Buick Regal 2.0 Turbo (SOLD 2007 Grand Prix GT. Front and rear PLOGs, 1.8 roller rockers, CAI, HPTuned, 3.4 pulley, TEP transmission, 90# springs, rollmaster single chain, Impala front brakes d/s rotors.) Past (Pontiacs) Grand Prix- 97 GT, 03 GT, 04 GT, 04 Comp G, 78 Trans am, 92 Trans Am.
    Reply With Quote  
     

  12. #32 Re: E85 startup tuning??? 
    GXP Level Member GTPpower's Avatar
    Join Date
    May 2008
    Location
    Schuyler, NE
    Posts
    2,972
    Thanks (Received)
    8
    Likes (Received)
    23
    Dislikes (Received)
    0
    Email it to me.
    Reply With Quote  
     

  13. #33 Re: E85 startup tuning??? 
    GTP Level Member
    Join Date
    Jun 2016
    Location
    Cleveland ohio
    Posts
    890
    Thanks (Received)
    1
    Likes (Received)
    9
    Dislikes (Received)
    0
    Awesome! Send your email to rickisrad04@yahoo.com

    I smoked a whole cigar through it and found no leaks.
    Reply With Quote  
     

  14. #34 Re: E85 startup tuning??? 
    GXP Level Member GTPpower's Avatar
    Join Date
    May 2008
    Location
    Schuyler, NE
    Posts
    2,972
    Thanks (Received)
    8
    Likes (Received)
    23
    Dislikes (Received)
    0
    It's the same email from earlier this week when you sent me your tune.
    Reply With Quote  
     

  15. #35 Re: E85 startup tuning??? 
    GTP Level Member
    Join Date
    Jun 2016
    Location
    Cleveland ohio
    Posts
    890
    Thanks (Received)
    1
    Likes (Received)
    9
    Dislikes (Received)
    0
    Just checking if you received it bro?
    Reply With Quote  
     

  16. #36 Re: E85 startup tuning??? 
    GXP Level Member GTPpower's Avatar
    Join Date
    May 2008
    Location
    Schuyler, NE
    Posts
    2,972
    Thanks (Received)
    8
    Likes (Received)
    23
    Dislikes (Received)
    0
    I did see it come through. I haven't been able to get to a computer to look at it yet though.
    Reply With Quote  
     

  17. #37 Re: E85 startup tuning??? 
    Donating Users bandook's Avatar
    Join Date
    Apr 2015
    Location
    Columbus, OH
    Posts
    1,781
    Thanks (Received)
    2
    Likes (Received)
    27
    Dislikes (Received)
    0
    Are you getting misfires? You should log them, and injector duty cycle too. Looks like vac leak to me. Your trims start to go negative right before you enter PE. If you are motivated you can make a simple smoke machine with a soldering iron, a paint can, baby oil, rag and some tube and 2 fittings. Very simple, costs 30 bucks at most and has helped me tons.
    Top Swapped 01 Imp
    VS (very small?) cam, SD Headers, 2.8" pulley, 29°, ported everything, E85, AEM water/meth, Deka 60's, HPT tuned
    Reply With Quote  
     

  18. #38 Re: E85 startup tuning??? 
    Donating Users bandook's Avatar
    Join Date
    Apr 2015
    Location
    Columbus, OH
    Posts
    1,781
    Thanks (Received)
    2
    Likes (Received)
    27
    Dislikes (Received)
    0
    Maybe even an exhaust leak before your O2. Does it smell super rich?
    Top Swapped 01 Imp
    VS (very small?) cam, SD Headers, 2.8" pulley, 29°, ported everything, E85, AEM water/meth, Deka 60's, HPT tuned
    Reply With Quote  
     

  19. #39 Re: E85 startup tuning??? 
    GTP Level Member
    Join Date
    Jun 2016
    Location
    Cleveland ohio
    Posts
    890
    Thanks (Received)
    1
    Likes (Received)
    9
    Dislikes (Received)
    0
    I have checked this thing up and down for a vacuum leak. I have sprayed the lines and intake down and inspected every connection. For a smoke test on these a cigar works very well. Take the brake booster off and light the cigar and let the hose smoke it. I’ve done it on other cars and it showed the leak in a hurry!!!!! I will check the exhaust header connection at down pipe again. Once I get some money I am going to replace the o2 sensor as a try. In the mean time I will continue to check for vacuum and exhaust leaks.
    Reply With Quote  
     

  20. #40 Re: E85 startup tuning??? 
    GXP Level Member GTPpower's Avatar
    Join Date
    May 2008
    Location
    Schuyler, NE
    Posts
    2,972
    Thanks (Received)
    8
    Likes (Received)
    23
    Dislikes (Received)
    0
    Yeah, definitely look for an exhaust leak. I looked at your scan....your O2 is reading weird. It's not consistent like I would see with a vacuum leak. It looks more like an exhaust leak pre O2 or just a bad sensor.

    If you want, you can disable the o2 and see if the car runs better.

    In your VCM editior,
    Engine>Fuel>Oxygen Sensors

    Change "closed loop enable" to 284.

    That will keep it from using the O2 sensor for fueling calculations. Keep in mind that the car isn't made to run permanently like this, it's just for testing.


    2001 GTP Drag Car - XPZ, Tischler heads, Upsidedown M90 IC'd, e85, Gen V, 2.3 w/ 5%OD
    2005 F350 6.0 - studded, deleted, tuned
    2001 GTP - cam, headers, nitrous, stock trans - 11.83 @ 116 <$2k in mods - sold
    Reply With Quote  
     

  21. Thanks rickisrad thanked for this post
Page 2 of 3 FirstFirst 123 LastLast

Similar Threads

  1. Bad startup when cold....
    By sco77 in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 12
    Last Post: 10-28-2013, 07:23 AM
  2. Fan Startup
    By Chadgervais in forum General Grand Prix Discussion
    Replies: 1
    Last Post: 09-12-2012, 09:15 AM
  3. Startup issue with the GTP
    By guitarguyucf in forum 1997-2007 4 speed Automatic (4T65E) (4T65E-HD)
    Replies: 3
    Last Post: 09-29-2010, 09:53 PM
  4. oil burn at startup?
    By Golgo13 in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 1
    Last Post: 11-18-2008, 07:18 PM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •