Thread: 2000 suburban 5.3 l bad intake gasket?

Results 1 to 17 of 17
  1. #1 2000 suburban 5.3 l bad intake gasket? 
    GTP Level Member
    Join Date
    Oct 2014
    Posts
    766
    Thanks (Received)
    2
    Likes (Received)
    7
    Dislikes (Received)
    0
    Pretty sure I have this diagnosed as a leaking intake manifold gasket that seals up when warm. Has a lean code on both banks. P0172 and P0174 iirc

    Here is a cold start at -5 F with the block heater plugged in. Idle surges for 45 seconds or so when temp is below 10F. After it warms up runs great and runs great on any other start that day.

    https://vimeo.com/198207399


    Sent from my iPhone using Tapatalk
    Reply With Quote  
     

  2. #2 Re: 2000 suburban 5.3 l bad intake gasket? 
    GTP Level Member
    Join Date
    Oct 2014
    Posts
    766
    Thanks (Received)
    2
    Likes (Received)
    7
    Dislikes (Received)
    0
    Sorry video error on my part. I will grab one tomorrow.


    Sent from my iPhone using Tapatalk
    Reply With Quote  
     

  3. #3 Re: 2000 suburban 5.3 l bad intake gasket? 
    GTP Level Member
    Join Date
    Oct 2014
    Posts
    766
    Thanks (Received)
    2
    Likes (Received)
    7
    Dislikes (Received)
    0
    Got the parts already. Will do the knock sensors while I'm in there.


    Sent from my iPhone using Tapatalk
    Reply With Quote  
     

  4. #4 Re: 2000 suburban 5.3 l bad intake gasket? 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,919
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    might want to change the k/s harness while your there too, they get beat up from the heat and can and will break if they want to. if yours has them foam inserts at the front and rear of the manifold toss them in the trash, and then you'll want to rtv the foam covers over the knock sensors to seal them up, the rear one will likely be full of water. the rtv stops that.

    like so.


    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  5. #5 Re: 2000 suburban 5.3 l bad intake gasket? 
    GTP Level Member
    Join Date
    Oct 2014
    Posts
    766
    Thanks (Received)
    2
    Likes (Received)
    7
    Dislikes (Received)
    0
    Yep saw that on you tube. Picked up a new harness and RTV as well. Thanks for the tips. Hardest part seems to be not breaking any 17 year old plastic parts you have to undo.


    Sent from my iPhone using Tapatalk
    Reply With Quote  
     

  6. #6 Re: 2000 suburban 5.3 l bad intake gasket? 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,919
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    the evap line down the back of the engine is a fun one. other then that its not all that bad, dont loose the fuel line o rings, they are 40 bucks to replace with ones that work. dealer only item. you can use other types but they all seem to leak later on. yes, i lost one, only to find it over a year later in the gravel driveway i was working on.


    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  7. #7 Re: 2000 suburban 5.3 l bad intake gasket? 
    GTP Level Member
    Join Date
    Oct 2014
    Posts
    766
    Thanks (Received)
    2
    Likes (Received)
    7
    Dislikes (Received)
    0
    Are those at the main rail disconnect? I planned on leaving the rail on the intake.


    Sent from my iPhone using Tapatalk
    Reply With Quote  
     

  8. #8 Re: 2000 suburban 5.3 l bad intake gasket? 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,919
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    theres a hard fuel line over the top of the manifold, pretty sure it had to come off. i ended up removing it. its been like 4 years since i did the job so all events are foggy at best. i recall all the headaches tho like it was yesterday lol

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  9. #9 Re: 2000 suburban 5.3 l bad intake gasket? 
    I live here. Below Average Joe's Avatar
    Join Date
    Aug 2011
    Location
    'Merica
    Posts
    7,358
    Thanks (Received)
    0
    Likes (Received)
    1
    Dislikes (Received)
    1
    Did this to my Silverado as well. I removed the fuel rail iirc. There is a special tool you are supposed to use to disconnect the lines for the rail. i cut a sharpie cap in half, the sliced one side down the middle so it can fit over the rail. Press it into the clip and it should come free. Its been a few years as well for me, so all of the steps seem foggy too.
    Quote Originally Posted by Sven The Sexman View Post
    Bill had a major role in all of the Star Wars movies; he was the force.
    Reply With Quote  
     

  10. #10 Re: 2000 suburban 5.3 l bad intake gasket? 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,919
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    Quote Originally Posted by Below Average Joe View Post
    Did this to my Silverado as well. I removed the fuel rail iirc. There is a special tool you are supposed to use to disconnect the lines for the rail. i cut a sharpie cap in half, the sliced one side down the middle so it can fit over the rail. Press it into the clip and it should come free. Its been a few years as well for me, so all of the steps seem foggy too.
    the same fuel line quick disconnect tool we use for the gp's works to get the line off the rail.

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  11. #11 Re: 2000 suburban 5.3 l bad intake gasket? 
    I live here. Below Average Joe's Avatar
    Join Date
    Aug 2011
    Location
    'Merica
    Posts
    7,358
    Thanks (Received)
    0
    Likes (Received)
    1
    Dislikes (Received)
    1
    Sharpie cap was free dollars. I'm cheap.....
    Quote Originally Posted by Sven The Sexman View Post
    Bill had a major role in all of the Star Wars movies; he was the force.
    Reply With Quote  
     

  12. #12 Re: 2000 suburban 5.3 l bad intake gasket? 
    GTP Level Member
    Join Date
    Oct 2014
    Posts
    766
    Thanks (Received)
    2
    Likes (Received)
    7
    Dislikes (Received)
    0
    If I pop the fuel rail off do I lube the o rings with oil or something when reassembling?


    Sent from my iPhone using Tapatalk
    Reply With Quote  
     

  13. #13 Re: 2000 suburban 5.3 l bad intake gasket? 
    GTP Level Member
    Join Date
    Oct 2014
    Posts
    766
    Thanks (Received)
    2
    Likes (Received)
    7
    Dislikes (Received)
    0
    Fricken Murphy's law. Threaten to put a wrench to it and it starts fine. -9 F cold start block heater plugged in this am and I do the video right and no surging. Solid idle.
    https://vimeo.com/198347543



    Sent from my iPhone using Tapatalk
    Reply With Quote  
     

  14. #14 Re: 2000 suburban 5.3 l bad intake gasket? 
    GTP Level Member
    Join Date
    Oct 2014
    Posts
    766
    Thanks (Received)
    2
    Likes (Received)
    7
    Dislikes (Received)
    0
    It was 42 today so I decided to just change the knock sensors and gaskets. Did notice a mouse was constructing a nest in an area where I thought the intake was leaking. Maybe some crap sealed it up. Anyway dove in. Pretty straight forward. Lots of cleaning to do.




    Sent from my iPhone using Tapatalk
    Reply With Quote  
     

  15. #15 Re: 2000 suburban 5.3 l bad intake gasket? 
    GTP Level Member
    Join Date
    Oct 2014
    Posts
    766
    Thanks (Received)
    2
    Likes (Received)
    7
    Dislikes (Received)
    0
    Took about 4.5 hours. With the cleaning.



    Did the RTV trick
    https://vimeo.com/200284458
    Seems to work!!


    Sent from my iPhone using Tapatalk
    Reply With Quote  
     

  16. #16 Re: 2000 suburban 5.3 l bad intake gasket? 
    GTP Level Member
    Join Date
    Oct 2014
    Posts
    766
    Thanks (Received)
    2
    Likes (Received)
    7
    Dislikes (Received)
    0

    Before gaskets placed.


    Sent from my iPhone using Tapatalk
    Reply With Quote  
     

  17. #17 Re: 2000 suburban 5.3 l bad intake gasket? 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,919
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    she cleaned up nice.

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

Similar Threads

  1. upper intake and lower intake manifold gasket
    By RICKS04GTP in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 16
    Last Post: 01-22-2014, 12:06 PM
  2. intake manifold gasket or head gasket
    By Eric Whitter in forum 3.1L V6 (LHO/LG8)
    Replies: 10
    Last Post: 05-17-2012, 01:55 AM
  3. Help is it head gasket water pump or intake gasket
    By jared71 in forum Introductions/Noob Questions
    Replies: 6
    Last Post: 02-14-2012, 01:26 PM
  4. Coolant Loss, intake Gasket or Intake Itself???
    By WoR in forum General Tech Discussion
    Replies: 2
    Last Post: 04-29-2009, 04:02 PM
Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •