Awesome thread.
I have two. I've had an electric Rustler 2wd for about 10 years, i think the only thing that's original is the chassis.
Recently purchased a Arrma Senton 6s. This thing is a whole new experience...
Printable View
Awesome thread.
I have two. I've had an electric Rustler 2wd for about 10 years, i think the only thing that's original is the chassis.
Recently purchased a Arrma Senton 6s. This thing is a whole new experience...
I left my Torment brushed. The Ruckus ended up with all of the goodies, I even did the 32p gear swap, I think I need a smaller spur and a bigger pinion though on 2s it wheelies like a mofo but is slow as all hell.
Pretty sure I have 19 cars now.
https://www.grandprixforums.com/atta...id=16676&stc=1
So who's buying one? Primal RC 1/5 Scale Raminator Monster Truck
Not I. I did buy a 1/10 E Revo finally though just this weekend. Already broke of course. Plastic driveshafts are stupid
https://www.grandprixforums.com/atta...id=16702&stc=1
my brothers got a revo. 55 mph right out the box.
that 1/5 scale rc is a monster. 3k is a bit steep tho.
The ram isnt even worth the time, stupidly priced. I could build something faster, stronger for half that.
Right Scotty. They claim this will do 70+ with a gear change. I like where it’s at though. It’s a good balance of speed and acceleration
gas revo, 55 out the box. my brother has one, ive played with it.
30 mph im talking about the 80 lb 1/5 th scale monster.
nitro not gas idiot old man.
30-35 is all you need for offroading. Hauling ass is fun on a big open coarse. On a street it gets old fast just zipping by, turning around, and zipping again.
So this thing is a turd. I kept breaking stub axles just running it around the rc track, the servo saver is a joke and basically useless, the plastic parts were too soft and flexible and it handled like crap.
Then this happened...... and guess what parts are basically non existent? So that this got scrapped.
https://i.imgur.com/Lryl4wz.jpg
And because one cannot have too many cars, I decided to pick up a NT48.3 roller off the RCTech classified section. Well short story long it would have cost me a few hundred dollars more to keep it nitro so I converted it to electric and tossed in a couple of upgrades while I was at it.
MC2 chassis stiffener kit.
M2C rear chassis brace.
M2C solid center brace.
Castle Creations Mamba Monster 2.
Arrma BLX185 2050kv motor.
Savox 2273SG servo.
I still need to trim and paint the ET48 body.
https://i.imgur.com/vbJPtFU.jpg
https://i.imgur.com/z3WFgoW.jpg
https://i.imgur.com/YGdVNYd.jpg
I dont understand your 2 month old repost
I dunno, I dont see it now. I dont know whats going on. YOu need more nitro monster trucks and 1/5
Ya everything is gone now.
Fixed the tamiya, wheel spun the nut off, I found the wheel spacer but not the pin, atleast it didnt break.
Took out the nitro 1/8, one point did like 20 cartwheels and now it doesnt turn left very good but everything looks fine.. ugh
I wonder what one of these actually looks like painted.
1/18TH PONTIAC GRAND PRIX BODY FOR HPI MICRO RS4 XRAY M18 OVAL NASCAR – Team Bluegroove
meh the nascar gayness