Thread: Bandook's 01 Imp, top swap-ified

Page 11 of 32 FirstFirst ... 91011121321 ... LastLast
Results 201 to 220 of 632
  1. #201 Re: Top Swap in progress, few questions 
    GTP Level Member 231FUN's Avatar
    Join Date
    Dec 2011
    Location
    Ontario,Canada
    Posts
    861
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Stock lifters for the win, ls7 lifters are a waste of money you could have spent on other mods unless your stock lifters were bad/ticking.
    Did you measure for correct push rod length with the new lifters? ls7 lifters are an oem replacement but only because they're the only thing available that's close...they're not the same as stock 3800 lifters.
    Reply With Quote  
     

  2. #202 Re: Top Swap in progress, few questions 
    Donating Users bandook's Avatar
    Join Date
    Apr 2015
    Location
    Columbus, OH
    Posts
    1,781
    Thanks (Received)
    2
    Likes (Received)
    27
    Dislikes (Received)
    0
    Yeah, heads were off when I cleaned all the threads. Don't remember if I used loctite though. I took the oil cap off and stuck my homemade listening device(vac line) in there and it sounds like the rockers. Its just frustrating trying to pinpoint sounds kwim? I'm waiting on a set of 1.9's whenever the seller gets them off the car, so I'll just redo them then. I heard all the hate about the comp bolts, guess I'll get some stockers when I redo them.

    I'm considering getting the pushrod measuring thing-a-ma-jig too. Since I had valve work done I'm feeling I'm close to the edge of spec for the ls7 lifters with stock rods.
    Top Swapped 01 Imp
    VS (very small?) cam, SD Headers, 2.8" pulley, 29°, ported everything, E85, AEM water/meth, Deka 60's, HPT tuned
    Reply With Quote  
     

  3. #203 Re: Top Swap in progress, few questions 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,815
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    I've never used anything besides the comp bolts, like so many others...nothing but good in my experience.

    Pull the valve covers and check the bolts. You don't want any ugliness because things were flopping around.
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  4. #204 Re: Top Swap in progress, few questions 
    Donating Users bandook's Avatar
    Join Date
    Apr 2015
    Location
    Columbus, OH
    Posts
    1,781
    Thanks (Received)
    2
    Likes (Received)
    27
    Dislikes (Received)
    0
    OK, thanks Bill. Thinking to just blind guess some shorter pushrods. I had 8 thou milled off the heads, and a valve job. Would probably be safe to just buy rods that are 10 thou shorter. Or even more because the valves opened a little when I tightened them down initially. Ls7 specs are .020-.050 from what I've seen.

    Or I could do it the right way and measure exact length I need, I suppose.
    Top Swapped 01 Imp
    VS (very small?) cam, SD Headers, 2.8" pulley, 29°, ported everything, E85, AEM water/meth, Deka 60's, HPT tuned
    Reply With Quote  
     

  5. #205 Re: Top Swap in progress, few questions 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,815
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    You could start by torquing them down properly. If you are concerned about pr length do a compression test. See if you are low.
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  6. #206 Re: Top Swap in progress, few questions 
    Donating Users bandook's Avatar
    Join Date
    Apr 2015
    Location
    Columbus, OH
    Posts
    1,781
    Thanks (Received)
    2
    Likes (Received)
    27
    Dislikes (Received)
    0
    Yes sir, will do . Ordered the comp pr length checkermajig. Will do a proper check on them and retorqe em all.

    I've always been a little confused about checking length with hydrolic lifters. Do I just crank the engine a few times before checking to keep them pumped?
    Top Swapped 01 Imp
    VS (very small?) cam, SD Headers, 2.8" pulley, 29°, ported everything, E85, AEM water/meth, Deka 60's, HPT tuned
    Reply With Quote  
     

  7. #207 Re: Top Swap in progress, few questions 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,815
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    Since i have never checked length (see...I torqued them properly after hearing the clatter..lol). Hopefully your checker comes with instructions.

    FWIW, stop being such a girl and pop the VC's off, recheck the torque and smile when you find that one was loose.
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  8. #208 Re: Top Swap in progress, few questions 
    GrandPrix Junkie CrazyGuy03's Avatar
    Join Date
    Jan 2010
    Location
    Buffalo
    Posts
    3,868
    Thanks (Received)
    0
    Likes (Received)
    2
    Dislikes (Received)
    0
    The stock lifters have a pretty wide "room for error" range Read up about it for the exact amount
    2003 Buick Regal GSX lots of mods - click here to see latest build - http://www.grandprixforums.net/threa...ld-for-the-gsx

    *For Reference - Does not have a Zack Howard Cam - It's an Intense Stage 3 - Thank You*
    Reply With Quote  
     

  9. #209 Re: Top Swap in progress, few questions 
    Donating Users bandook's Avatar
    Join Date
    Apr 2015
    Location
    Columbus, OH
    Posts
    1,781
    Thanks (Received)
    2
    Likes (Received)
    27
    Dislikes (Received)
    0
    Quote Originally Posted by RickyBobby03 View Post
    The stock lifters have a pretty wide "room for error" range Read up about it for the exact amount
    Yeah, ls7 are .020-.050 I believe. I should be good but I had 2 valve jobs done and the heads surfaced. I'll measure just for piece of mind.
    Top Swapped 01 Imp
    VS (very small?) cam, SD Headers, 2.8" pulley, 29°, ported everything, E85, AEM water/meth, Deka 60's, HPT tuned
    Reply With Quote  
     

  10. #210 Re: Top Swap in progress, few questions 
    Donating Users bandook's Avatar
    Join Date
    Apr 2015
    Location
    Columbus, OH
    Posts
    1,781
    Thanks (Received)
    2
    Likes (Received)
    27
    Dislikes (Received)
    0
    Checked rockers today, everything is tight and there is no play. Did find a bad pulley, plastic junk so replaced with a new metal one. Think that was some of the noise I was hearing.

    So I put it back together, and had it idling for 5 minutes. Then...it died. And won't start. Fried another fuel pump. Sheesh. The relay was very warm to the touch too, so that confirms the pump was on the way out right? Drawing too much current until it fried? Put new relay in, got 12v to the pump but no whirrr. Hammered the tank but no luck.

    So...I want a frigging reliable pump with no hack job on the canister that I can run to empty. What are my options? How far can you take a stock ac delco? I could do the venturi walbro but I need a new canister too.
    Top Swapped 01 Imp
    VS (very small?) cam, SD Headers, 2.8" pulley, 29°, ported everything, E85, AEM water/meth, Deka 60's, HPT tuned
    Reply With Quote  
     

  11. #211 Re: Top Swap in progress, few questions 
    Donating Users bandook's Avatar
    Join Date
    Apr 2015
    Location
    Columbus, OH
    Posts
    1,781
    Thanks (Received)
    2
    Likes (Received)
    27
    Dislikes (Received)
    0
    Pulled the pump out and hooked it up to 12v. Nothing. Banged it on the ground and.... boom! It blew up. No, not really, but it did start working again. Hoping just some goo got lodged in there. While I had it out, for the umpteenth time, I hacked it even more.


    Why not I guess. Cut the bottom out and pushed it down about 2 inches more. Still don't trust this hillbilly setup, need something more reliable.
    Top Swapped 01 Imp
    VS (very small?) cam, SD Headers, 2.8" pulley, 29°, ported everything, E85, AEM water/meth, Deka 60's, HPT tuned
    Reply With Quote  
     

  12. #212 Re: Top Swap in progress, few questions 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,919
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    id cut the whole bottom off but leave 4 little legs to keep the sock off the tank bottom a 1/4 inch or so.

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  13. #213 Re: Top Swap in progress, few questions 
    Donating Users bandook's Avatar
    Join Date
    Apr 2015
    Location
    Columbus, OH
    Posts
    1,781
    Thanks (Received)
    2
    Likes (Received)
    27
    Dislikes (Received)
    0
    That's what I did. I didn't cut up the sides, there are a bunch of holes I drilled there.
    Top Swapped 01 Imp
    VS (very small?) cam, SD Headers, 2.8" pulley, 29°, ported everything, E85, AEM water/meth, Deka 60's, HPT tuned
    Reply With Quote  
     

  14. #214 Re: Top Swap in progress, few questions 
    GXP Level Member Grimsin's Avatar
    Join Date
    Feb 2011
    Location
    St Thomas Ontario
    Posts
    2,316
    Thanks (Received)
    0
    Likes (Received)
    1
    Dislikes (Received)
    0
    Gotta change your thread title. Its old lol.
    Reply With Quote  
     

  15. #215 Re: Top Swap in progress, few questions 
    Donating Users bandook's Avatar
    Join Date
    Apr 2015
    Location
    Columbus, OH
    Posts
    1,781
    Thanks (Received)
    2
    Likes (Received)
    27
    Dislikes (Received)
    0
    Not a bad idea...don't know how though lol.

    I'm 99% sure my engine noise is an exhaust leak. Yay SD headers! I reused the stock gaskets, and don't think I can get them much tighter. Sounds like front manifold is the culprit. Guess I can try some new gaskets.
    Top Swapped 01 Imp
    VS (very small?) cam, SD Headers, 2.8" pulley, 29°, ported everything, E85, AEM water/meth, Deka 60's, HPT tuned
    Reply With Quote  
     

  16. #216 Re: Top Swap in progress, few questions 
    GXP Level Member Grimsin's Avatar
    Join Date
    Feb 2011
    Location
    St Thomas Ontario
    Posts
    2,316
    Thanks (Received)
    0
    Likes (Received)
    1
    Dislikes (Received)
    0
    click "edit post" on your very forst post on this thread, change title and all done

    3.8l N/A POWA! :4'' HAI\L67 HVTB\HV3\ER Rockers\WP underdrive pulley\Headers\cat delete\91 octane overkill incar tune.3.69 gears, Trans go shift kit.
    My Car:http://www.grandprixforums.net/threa...2005-Impala-LS
    Reply With Quote  
     

  17. #217 Re: Bandook's 01 Imp, top swap-ified 
    Donating Users bandook's Avatar
    Join Date
    Apr 2015
    Location
    Columbus, OH
    Posts
    1,781
    Thanks (Received)
    2
    Likes (Received)
    27
    Dislikes (Received)
    0
    Oh, neat. Thanks
    Top Swapped 01 Imp
    VS (very small?) cam, SD Headers, 2.8" pulley, 29°, ported everything, E85, AEM water/meth, Deka 60's, HPT tuned
    Reply With Quote  
     

  18. #218 Re: Bandook's 01 Imp, top swap-ified 
    Donating Users bandook's Avatar
    Join Date
    Apr 2015
    Location
    Columbus, OH
    Posts
    1,781
    Thanks (Received)
    2
    Likes (Received)
    27
    Dislikes (Received)
    0
    Well, the fuel pump is done. Or I'm done with it. Put a new gasket on front header. Started it up an it died after 2 minutes. No fuel, no bueno .

    Really interested in your opinions on pumps. Will a stock pump be good down to a 3.0 pulley, ported heads, headers, rr's? Plan on doing a cam next spring too. Just don't see much discussion on pumps. Would like to order something tonight. I'm thinking the walbro venturi pump. I'll also have to buy a canister, which I can't just buy the canister alone so I'm thinking of buying a 35 dollar pump on eBay just for the canister. Help?
    Top Swapped 01 Imp
    VS (very small?) cam, SD Headers, 2.8" pulley, 29°, ported everything, E85, AEM water/meth, Deka 60's, HPT tuned
    Reply With Quote  
     

  19. #219 Re: Bandook's 01 Imp, top swap-ified 
    Donating Users bandook's Avatar
    Join Date
    Apr 2015
    Location
    Columbus, OH
    Posts
    1,781
    Thanks (Received)
    2
    Likes (Received)
    27
    Dislikes (Received)
    0
    Paint my cheeks red, but I don't think I have a venturi pump. I was thinking that the dual pickups on the bottom made it a venturi. But doesn't it need a second smaller fuel hose coming off the top to make it venturi? Confused myself again. Just another day in the life of Dook...
    Top Swapped 01 Imp
    VS (very small?) cam, SD Headers, 2.8" pulley, 29°, ported everything, E85, AEM water/meth, Deka 60's, HPT tuned
    Reply With Quote  
     

  20. #220 Re: Bandook's 01 Imp, top swap-ified 
    SE Level Member
    Join Date
    Aug 2010
    Location
    missouri
    Posts
    65
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Quote Originally Posted by bandook View Post
    Paint my cheeks red, but I don't think I have a venturi pump. I was thinking that the dual pickups on the bottom made it a venturi. But doesn't it need a second smaller fuel hose coming off the top to make it venturi? Confused myself again. Just another day in the life of Dook...

    yes. that small black hose tells you if you have a venturi pump or not. small black hose = no small black hose =
    2000 Grand Prix 3.8 top swapped gt, headers, ported gen 3 blower, 3" catless downpipe, overkilled tune, CAI, 180, transgo shift kit, C5 front calipers, 12" f body rotors, GMPP sway bars, racetronix venturi pump w/rewire. Coming soon: strut braces
    Reply With Quote  
     

Page 11 of 32 FirstFirst ... 91011121321 ... LastLast

Similar Threads

  1. Couple questions regarding build in progress
    By crbquist in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 8
    Last Post: 04-22-2013, 11:03 AM
  2. Top swap Progress
    By 01GrandPrixTURBOGT in forum 3.8L V6 Naturally Aspirated (L36)(L26)
    Replies: 3
    Last Post: 12-15-2012, 05:55 PM
  3. Top Swap progress
    By 01GrandPrixTURBOGT in forum 3.8L V6 Naturally Aspirated (L36)(L26)
    Replies: 20
    Last Post: 09-14-2012, 07:04 PM
  4. Pics of my swap progress
    By NineD9GT in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 17
    Last Post: 03-04-2010, 02:44 PM
  5. Swap questions...
    By motohead in forum 3.1L V6 (LHO/LG8)
    Replies: 0
    Last Post: 06-29-2009, 11:12 AM
Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •