Thread: 97 GP GT - Let's project a project car (from trailer to driving)

Page 3 of 5 FirstFirst 12345 LastLast
Results 41 to 60 of 98
  1. #41 Re: 97 GP GT - Let's project a project car (from trailer to driving) 
    I live here. TLSheff's Avatar
    Join Date
    Dec 2009
    Location
    Durant, Oklahoma, United States
    Posts
    8,033
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Quote Originally Posted by penright View Post
    I saw in one of your post about getting an oven in your shop to powder coat small parts. At sometime I was going to ask about that. I assume it is a do it yourself powder coating. Where do you buy the material? I guess the process creates a mess, that is why I don't want to use the wife's. :-) How hard is the process? Expensive? Maybe when you get sometime, you can show me how.
    Custom Powder Coating


    Quote Originally Posted by penright View Post
    How do "delete the "5th soft line""? I did some googling and did not see it.
    ZZPerformance - 5th Stainless Brake Line #ZZ-5BRKLN

    He used one of these, its just a short piece that connects 2 metal lines and factory line is rubber. Using the SS line helps keep pressure up and replaced old parts that are old. lol Not necessary but a good option to look at if you have the budget.
    Old thread but good info regarding it here.

    Quote Originally Posted by AmericanSoldier View Post
    ...not scanning/monitoring your motor is like bangin a hooker and you just HOPE your not infected.
    Reply With Quote  
     

  2. #42 Re: 97 GP GT - Let's project a project car (from trailer to driving) 
    GT Level Member penright's Avatar
    Join Date
    Mar 2013
    Location
    United States
    Posts
    260
    Thanks (Received)
    0
    Likes (Received)
    1
    Dislikes (Received)
    0
    Here are my thoughts as of today, as you all know things keep changing. I ran across a GP at the local pull a part, that someone must have just replaced the front end and back end. It had new CV (don't think they would have fit my 97), really good taillights, with a blown motor. One thing I needed was a deck lid latch, this car looked brand new. One of the bearings is already gone. Since pull a part pulls the wheels and tires, I can't see how much play there is, unless someone has a trick? I was going to make a bar that I can bolt on, to see if there is any play, I have not had a chance to try that yet. Back to the story, the wire loom was spotless, my car is only two years older and mine is dusty. So for ten bucks apiece, new rotors, these look brand new ....20130719_200956_zps9a385f3f.jpg Photo by penright | Photobucket So no Fbody mods AT THIS TIME :-). I still need to do the front, but I will do it when do the front bearings and tie rods.

    She may not want it, but I starting to think this may be a good car for the granddaughter. This is really starting to clean up. Once I get the front bearings, tie rods, valve cover gaskets, and finish flushing the radiator, I would not be afraid for her to drive it. Now until the cosmetics stuff is done, she may not want to. :-)

    Got the trunk done. Here are the befores... 20130719_200956_zps9a385f3f.jpg Photo by penright | Photobucket ,
    20130617_191711_zpsc06ebb95.jpg Photo by penright | Photobucket,
    20130617_191748_zps500a8ed2.jpg Photo by penright | Photobucket
    and the after 20130719_185956_zps7f14402e.jpg Photo by penright | Photobucket,
    20130719_191717_zpse6f3da67.jpg Photo by penright | Photobucket
    No rust in the jack, found a spare tire cover that wasn't busted, clean carpet, new deck lid latch, and put it back together. The old deck lid latch would buzz but not pop the trunk.

    Do have one question, before the spare tire, there is stireform that holds the jack, there is a threaded piece that has a yellow rubber over the threads. What is that?
    07 Grand Prix GXP (My Daily Driver and future toy) (120,000+)
    97 Grand Prix GT (Project Car) (178,000+)
    02 Mustang Convertible (Wife's Toy) (75,000+)
    17 Honda Civic (Wife's Daily Driver)
    Reply With Quote  
     

  3. #43 Re: 97 GP GT - Let's project a project car (from trailer to driving) 
    I live here. TLSheff's Avatar
    Join Date
    Dec 2009
    Location
    Durant, Oklahoma, United States
    Posts
    8,033
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0


    97-03 GPs should all look like this. Let me know what number you are referring to and I can provide GM#s for them. Pulled straight from my catalog at work.

    Quote Originally Posted by AmericanSoldier View Post
    ...not scanning/monitoring your motor is like bangin a hooker and you just HOPE your not infected.
    Reply With Quote  
     

  4. #44 Re: 97 GP GT - Let's project a project car (from trailer to driving) 
    GT Level Member penright's Avatar
    Join Date
    Mar 2013
    Location
    United States
    Posts
    260
    Thanks (Received)
    0
    Likes (Received)
    1
    Dislikes (Received)
    0
    Quote Originally Posted by TLSheff View Post
    97-03 GPs should all look like this. Let me know what number you are referring to and I can provide GM#s for them. Pulled straight from my catalog at work.
    I can't tell which one from the drawing. I think it's either 8 or 9.
    What is 6, 7, 8, and 9? 14 is the nut that holds the jack, is 6 the valve stem?

    Here the picture I took after getting it at pull - a - part.
    20130724_120906_zps79b12fe0.jpg Photo by penright | Photobucket
    I hate showing my ignorance, but I am just curious what it is used for?
    07 Grand Prix GXP (My Daily Driver and future toy) (120,000+)
    97 Grand Prix GT (Project Car) (178,000+)
    02 Mustang Convertible (Wife's Toy) (75,000+)
    17 Honda Civic (Wife's Daily Driver)
    Reply With Quote  
     

  5. #45 Re: 97 GP GT - Let's project a project car (from trailer to driving) 
    I live here. TLSheff's Avatar
    Join Date
    Dec 2009
    Location
    Durant, Oklahoma, United States
    Posts
    8,033
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Yes #6 is the valve stem for the spare tire.

    #7- Jack Warning Label
    #8- Spare Wheel Stow Bolt Extension
    #9- Spare Wheel Stow Guide

    #14 is likely what you are after. Jack Stow Retainer (40mm wing span) GM #10430943

    Quote Originally Posted by AmericanSoldier View Post
    ...not scanning/monitoring your motor is like bangin a hooker and you just HOPE your not infected.
    Reply With Quote  
     

  6. #46 Re: 97 GP GT - Let's project a project car (from trailer to driving) 
    GT Level Member penright's Avatar
    Join Date
    Mar 2013
    Location
    United States
    Posts
    260
    Thanks (Received)
    0
    Likes (Received)
    1
    Dislikes (Received)
    0
    Quote Originally Posted by TLSheff View Post
    Yes #6 is the valve stem for the spare tire.

    #7- Jack Warning Label
    #8- Spare Wheel Stow Bolt Extension
    #9- Spare Wheel Stow Guide

    #14 is likely what you are after. Jack Stow Retainer (40mm wing span) GM #10430943
    I have #14, I actually now have 8 and 9. I just curious what they are used for? I was hopping to know by looking at the names, but why do you need a stow bolt extension or guide? Did the picture help?
    [edit]
    Read the manual, I hope I don't lose and points on the man card. I guess when you have a flat and change to the spare. You can put one you pulled off in the spare tire spot by using the extension. I wonder how the cover would fit?


    Any the warning label has a part number. Wow, I thought I was OCD.
    Last edited by penright; 08-16-2013 at 08:18 AM.
    07 Grand Prix GXP (My Daily Driver and future toy) (120,000+)
    97 Grand Prix GT (Project Car) (178,000+)
    02 Mustang Convertible (Wife's Toy) (75,000+)
    17 Honda Civic (Wife's Daily Driver)
    Reply With Quote  
     

  7. #47 Re: 97 GP GT - Let's project a project car (from trailer to driving) 
    GT Level Member penright's Avatar
    Join Date
    Mar 2013
    Location
    United States
    Posts
    260
    Thanks (Received)
    0
    Likes (Received)
    1
    Dislikes (Received)
    0
    Thought about replacing the seals in the rack. The PS fluid was low, have not seen any drips yet, but my two 06's need it, this is the purpose of car, is to try something that I might not try on my drivers. I say this before I get the "Just get a reman" quotes. :-) Some of the questions I asked on the other thread, but I thought this one may have a different audience.

    I found this thread on R&R, but nothing on replacing seals. As I said, I have two 06's that could use it, from some chatter it sounds like the experience may be the same. Here's the thread : http://www.grandprixforums.net/04-ra...ment-2868.html
    Also another reason I think the experience would be the same, is I looked on rockauto and both kits seem to have the same part number, which leads to some questions ...

    I wonder if anyone has any experience replacing seals?
    TL, Would you have an exploded diagram of a 97 and 06 to compare?

    I am a little confused about the parts.
    This picture says "W/Magnetic Variable Assist" More Information for ACDELCO 36348363
    and this one does not say either way More Information for DORMAN 905515
    The 97 and the two 06's does not have MVA, while my 07 GXP does. So which kit is right for the 97 and 06s?

    Also in the spirit of testing, I really stepped out on a limb. I bought new both wheel bearings and both tie rods ends on ebay. Both wheel bearing shipped was $60 and both tie rods shipped was $18. Again, before I get the "you get what you pay for" posting, this is the purpose of this car. I did get the bearings and the box, color, and from China reminds me of the ones I bought from O'REilly's. The only difference is there was no instructions on being careful on the torque for the axle nut. If I remember right it was 150 ft pounds. Still waiting on the tie rod ends. I would like to make a decision on resealing the rack before I replace them. Them being the wheel bearings, tie rods, and links.


    Still got plenty to do, and school starts back 8/19. Next post, I may start a punch list.

    Just a start, not all inclusive, and not in order ....
    1. valve cover gaskets
    2. flush, new thermostat, clean overflow tank, and refill with antifreeze
    3. replace carpet
    4. replace shifter cable
    5. replace both front wheel bearings
    6. replace both outer tie rods
    7. replace both sides sway bar links
    8. finish headliner
    9. remove rear tint ( while all trim is out for carpet/headliner) Since everything is out of car, see if I can get a deal on re-tint.
    10. look at and remove side windows, if quality is good enough, may just try and match the rear as close as possible. Not sure if I want to tackle tint just yet. The sides look pretty good, I think I will just do the rear.
    11. install remote start
    12. Add flasher to mirror upgrade.
    13. Add Pontiac projectors to the doors.
    Last edited by penright; 08-16-2013 at 08:12 AM.
    07 Grand Prix GXP (My Daily Driver and future toy) (120,000+)
    97 Grand Prix GT (Project Car) (178,000+)
    02 Mustang Convertible (Wife's Toy) (75,000+)
    17 Honda Civic (Wife's Daily Driver)
    Reply With Quote  
     

  8. #48 Re: 97 GP GT - Let's project a project car (from trailer to driving) 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,919
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    cant help on the seal repair.

    but the magna steer, you'll want to look at the part of the rack where the column bolts to the rack, from the side of the rack by the boot there you'll see a wire coming from it. if you dont have magna steer theres no wire from the rack.

    some have it some dont. check your cars first, then order the parts.

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  9. #49 Re: 97 GP GT - Let's project a project car (from trailer to driving) 
    GTX Level Member AKGTP19's Avatar
    Join Date
    Mar 2013
    Location
    Fort Lauderdale, FL
    Posts
    721
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Quote Originally Posted by EricGTP View Post
    I love red coupes. Makes me miss my old one. Looks good man keep up the good work.


    i had a red one, they really are nice
    1998 GTP Loudmouth
    1999 GTP, Borla Cat Back.....SOLD
    Reply With Quote  
     

  10. #50 Re: 97 GP GT - Let's project a project car (from trailer to driving) 
    GT Level Member penright's Avatar
    Join Date
    Mar 2013
    Location
    United States
    Posts
    260
    Thanks (Received)
    0
    Likes (Received)
    1
    Dislikes (Received)
    0
    Work, School starting, and just other distractions, finally got to spend some time on the project. When you looked into the coolant over flow jug (COFJ), it was crusted with Dex. Pulled the thermostat out to give it a good flush and it was coated with brown gum. I will edit this with the thermostat picture later.
    Before all of COFJ, Before Close up inside

    Pulled the jug out and used some kind of soapy stuff I have for detailing engines. I threw in some small nuts and shook hard. Worked pretty good but there were some streaks that you could see. Then I added a red shop towel and that worked like a champ.
    After all of COFJ, After Close up of inside

    On a 97 the jug is on the left side and you need to move the air box out of the way. While I had it out and the seats and carpet out I replaced the shift cable. I don't remember what year I got the replacement on out of, but it was about foot shorter. I went ahead and put it in. It fit around the air box OK, but not as much room as the original. I will edit later with a picture when it is all back together. Right now I need to adjust it. With the shift in park, the trans leaver is about half way there. Also while I had it this far I replaced the rear valve cover gasket. While I was that far I flushed the heater core. I want to get some radiator flush and run through and maybe some seafoam, then drain and replace with new thermostat, antifreeze and fresh oil. Need to look at the list, but this should button up under the hood. At least till it time to start modding :-)

    Picture of thermostat, you can see how gum up it was inside ...
    Pix of Thermostat
    Last edited by penright; 09-03-2013 at 10:50 AM. Reason: Add Picture of thermostat to show how bad it was.
    07 Grand Prix GXP (My Daily Driver and future toy) (120,000+)
    97 Grand Prix GT (Project Car) (178,000+)
    02 Mustang Convertible (Wife's Toy) (75,000+)
    17 Honda Civic (Wife's Daily Driver)
    Reply With Quote  
     

  11. #51 Re: 97 GP GT - Let's project a project car (from trailer to driving) 
    Donating Users Kejross's Avatar
    Join Date
    Feb 2010
    Location
    Oklahoma City, OK
    Posts
    811
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Quote Originally Posted by penright View Post
    What size/specs? I am not against buying a new tool. :-) If not something special, I may have it. Back in the racing days we had some left handed taps. It was for when we made a rod with spherical ends, so as the bar was turned the length could be adjusted. I had a tool box stole from my friends garaged and lost them. :-(
    [Edit] Found this posting from TL. http://www.grandprixforums.net/f-bod...ket-70243.html
    Yeah that link has the specs, I couldn't find a 12mm drill bit anywhere so I got the standard conversion size. Don't have them here at my house but I wanna say it was like 35/64ths or 31/64ths. I just pop them on the drill press so the holes are nice and straight and the bit will pretty well center itself.



    Quote Originally Posted by penright View Post
    I saw in one of your post about getting an oven in your shop to powder coat small parts. At sometime I was going to ask about that. I assume it is a do it yourself powder coating. Where do you buy the material? I guess the process creates a mess, that is why I don't want to use the wife's. :-) How hard is the process? Expensive? Maybe when you get sometime, you can show me how.
    Also, do you know where we can pick up CAN spray clear coat?
    It's fairly cheap to get started and a pretty easy process. I buy my colors off ebay in 1-5lb packages. You buy a cheap oven off craigslist($50-75), then buy the harbor freight powder coat gun/kit (was like $75??), then you sandblast your parts, clip your alligator lead to the part or the wire hanging the part and spray your powder then bake at roughly 350 for about 15-20 minutes. The colors will have temp and time... The alligator lead runs a current through the part which attracts the powder to the part.




    Quote Originally Posted by penright View Post
    How do "delete the "5th soft line""? I did some googling and did not see it.

    Quote Originally Posted by TLSheff View Post
    He used one of these, its just a short piece that connects 2 metal lines and factory line is rubber. Using the SS line helps keep pressure up and replaced old parts that are old. lol Not necessary but a good option to look at if you have the budget.
    Old thread but good info regarding it here.
    Actually.... I bought a stick of brake line(1 foot I think) that already had the fittings on the end and bent it to shape with my tubing bender. Did I notice any difference from all the braided stainless lines and 5th hard line?? No, not really...



    Quote Originally Posted by penright View Post
    Work, School starting, and just other distractions, finally got to spend some time on the project. When you looked into the coolant over flow jug (COFJ), it was crusted with Dex. Pulled the thermostat out to give it a good flush and it was coated with brown gum. I will edit this with the thermostat picture later.
    Before all of COFJ, Before Close up inside

    Pulled the jug out and used some kind of soapy stuff I have for detailing engines. I threw in some small nuts and shook hard. Worked pretty good but there were some streaks that you could see. Then I added a red shop towel and that worked like a champ.
    After all of COFJ, After Close up of inside

    On a 97 the jug is on the left side and you need to move the air box out of the way. While I had it out and the seats and carpet out I replaced the shift cable. I don't remember what year I got the replacement on out of, but it was about foot shorter. I went ahead and put it in. It fit around the air box OK, but not as much room as the original. I will edit later with a picture when it is all back together. Right now I need to adjust it. With the shift in park, the trans leaver is about half way there. Also while I had it this far I replaced the rear valve cover gasket. While I was that far I flushed the heater core. I want to get some radiator flush and run through and maybe some seafoam, then drain and replace with new thermostat, antifreeze and fresh oil. Need to look at the list, but this should button up under the hood. At least till it time to start modding :-)
    Lot's of people(me for one) switch to the newer version of the overflow tank like the 99+ cars have. It gives you more room for intake stuffs on the side and in my opinion looks "cleaner". What kinda coolant did you go back with? I always made sure to get the "conventional green" they sell all kinds of green coolant but most of it is really still dexcool unless you get the real deal old stuff.
    SOLD-98 4dr GTP, l32 Swapped, IS2 heads, IS3 cam, S2 intercooler, S3 FMHE, E85, 65# inj, N* TB w/LQ4, OBX Headers, Borla catback, 3.0 zzp mps, lc-1 wideband, HP Tuners, PRJ wires, FWI, Lowered. 04 GTO M6, 07 Grand Prix LS4 powered GXP. 98 V6 GMC SWB, exhaust, custom intake. 09 HHR (Wifes)
    Reply With Quote  
     

  12. #52 Re: 97 GP GT - Let's project a project car (from trailer to driving) 
    GT Level Member penright's Avatar
    Join Date
    Mar 2013
    Location
    United States
    Posts
    260
    Thanks (Received)
    0
    Likes (Received)
    1
    Dislikes (Received)
    0
    Played hooky from the studies on Monday to work on the project car (TPC). Glad I did, the tie rods ends were not the right ones. . Lets see if I can get the cheap mail order swapped out. Again, all this is an experiment. They are about inch and half too short, I am afraid that there is not enough threads. If you look at the picture the designs look good, I like the grease zerk, how the rubber boot is clamped on with a rings, and the weep hole to keep from blowing out the boot.
    Both of Tie Rods Ends side by side


    Did get the passenger side, wheel bearing, rotor, and sway bar links done.
    Before:
    Rotor, not much left
    Sway Bar Link, this side is better than the other, it busted in half
    After:
    Rotor and new bearing
    Sway Bar Link, Not bad considering from a salvage
    07 Grand Prix GXP (My Daily Driver and future toy) (120,000+)
    97 Grand Prix GT (Project Car) (178,000+)
    02 Mustang Convertible (Wife's Toy) (75,000+)
    17 Honda Civic (Wife's Daily Driver)
    Reply With Quote  
     

  13. #53 Re: 97 GP GT - Let's project a project car (from trailer to driving) 
    GT Level Member penright's Avatar
    Join Date
    Mar 2013
    Location
    United States
    Posts
    260
    Thanks (Received)
    0
    Likes (Received)
    1
    Dislikes (Received)
    0
    I mention when I started the thread that I had one more semester. Just took the last finial, hopefully the last finial of my life. This Saturday our neighbor’s boy is getting married and besides I still have some ice in the driveway. Soon though and I will be back on it.

    For now since there is no more school not any football till Cotton Bowl, I need some good weather and it’s time to start backup.

    To refresh the current status, I was replacing the wheel bearing, outer tie rods, drag link, and rotor. I got the passenger side done except for the tie rod. Those have come in.

    Now just for some warm weather. :-)
    07 Grand Prix GXP (My Daily Driver and future toy) (120,000+)
    97 Grand Prix GT (Project Car) (178,000+)
    02 Mustang Convertible (Wife's Toy) (75,000+)
    17 Honda Civic (Wife's Daily Driver)
    Reply With Quote  
     

  14. #54 Re: 97 GP GT - Let's project a project car (from trailer to driving) 
    GT Level Member penright's Avatar
    Join Date
    Mar 2013
    Location
    United States
    Posts
    260
    Thanks (Received)
    0
    Likes (Received)
    1
    Dislikes (Received)
    0
    Finally spent some time on TPC. It has been so long, I had to re-read the posts to remember what I was doing. Back in march I started a punch list. I have finished the valve cover gaskets, flush and clean radiator, replace the sway bar link, and replaced shifter cable. I had pulled the interior to get at the headliner, carpet, shifter, and rear tint. As I said, I had one wheel bearing replaced and when I went to do the tie-rod the ones that shipped were the wrong ones. That was where I left off going back to school. After I finished, weather was too bad to work on it. After weather got better, seemed to have something that had to get done every Saturday. I did receive the correct tie-rods, finished off the passenger and started on driver side last night. I pulled the tie-rod off and then went to remove the sway bar link. The bolt was rusted all the way through.


    Check this out:



    Here is a close up of the crack:


    This picture is more detailed:



    So now I guess I need to add replace sway bar. I thought about pull-a-part, but as we all know GP are bad about this. Don’t really want to spend the money right now on a performance one. I might try and weld it, not like it going to turn on me if it breaks. I don’t know yet. Also started pulling the tint off the back glass. As you can imagine, it will be fun.


    So here is my updated punch list.
    1. replace both front wheel bearings
    2. replace both outer tie rods
    3. replace sway bar
    4. replace both sides sway bar links
    5. remove rear tint ( while all trim is out for carpet/headliner) Since everything is out of car, see if I can get a deal on re-tint.
    Get car aligned and rear window tinted
    6. finish headliner
    7. replace carpet
    8. install remote start
    9. Add flasher to mirror upgrade.
    10. Add Pontiac projectors to the doors.
    07 Grand Prix GXP (My Daily Driver and future toy) (120,000+)
    97 Grand Prix GT (Project Car) (178,000+)
    02 Mustang Convertible (Wife's Toy) (75,000+)
    17 Honda Civic (Wife's Daily Driver)
    Reply With Quote  
     

  15. #55 Re: 97 GP GT - Let's project a project car (from trailer to driving) 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,919
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    just buy a doman sway bar, its solid and under 100 bucks on line. even comes with new end links. id use some moog bushings tho, the dorman bar bushings suck.

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  16. #56 Re: 97 GP GT - Let's project a project car (from trailer to driving) 
    Donating Users 16MustangVet's Avatar
    Join Date
    May 2009
    Location
    Sh1t hole Afghanistan Currently
    Posts
    5,418
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    X2 doreman and moog end links and sway bushings, wrap some teflon tape around the sway where the bushings go and them put some white lithium grease on it that bar should never squeak again!.......
    Reply With Quote  
     

  17. #57 Re: 97 GP GT - Let's project a project car (from trailer to driving) 
    GT Level Member penright's Avatar
    Join Date
    Mar 2013
    Location
    United States
    Posts
    260
    Thanks (Received)
    0
    Likes (Received)
    1
    Dislikes (Received)
    0
    Quote Originally Posted by 98GrandPrixIraqVet View Post
    wrap some teflon tape around the sway where the bushings go
    Just too funny, NOT what you said but how I read it. The first couple of times I missed the part about "teflon" and "where bushing go".
    I mean Mythbusters proved how far you can push duct tape, but I guessing even it has it's limits. :-)

    Quote Originally Posted by Scottydoggs View Post
    just buy a doman sway bar, its solid and under 100 bucks on line. even comes with new end links. id use some moog bushings tho, the dorman bar bushings suck.
    I hear you. My thoughts are, "I know that was the first mistake :-)", just get it somewhat reliable going down the street. To that end I am tempted to hit the local Pull-a-part ($11), but would I find anything better? Just weld it to get it back on it's wheels? I have to pull it anyway, so I might see what it looks like out of the car.
    I know it's been over a year and still not there yet. But once I get a good base line then I can start to tweak. If I was going to spend a $100, maybe add the $80 for some performance? How much I do depends on how it looks and drives when we get to the base line.
    07 Grand Prix GXP (My Daily Driver and future toy) (120,000+)
    97 Grand Prix GT (Project Car) (178,000+)
    02 Mustang Convertible (Wife's Toy) (75,000+)
    17 Honda Civic (Wife's Daily Driver)
    Reply With Quote  
     

  18. #58 Re: 97 GP GT - Let's project a project car (from trailer to driving) 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,815
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    You could get a sway from an 00+ monte carlo. It's the same as the GMPP bar and would be less cost to pull from a yard.

    As for the cracked bar, that is a w body standard option.
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  19. #59 Re: 97 GP GT - Let's project a project car (from trailer to driving) 
    GT Level Member penright's Avatar
    Join Date
    Mar 2013
    Location
    United States
    Posts
    260
    Thanks (Received)
    0
    Likes (Received)
    1
    Dislikes (Received)
    0
    Quote Originally Posted by BillBoost37 View Post
    You could get a sway from an 00+ monte carlo. It's the same as the GMPP bar and would be less cost to pull from a yard.

    As for the cracked bar, that is a w body standard option.
    First post from tap. Actually second, it doesn't seem the first went through or there may be two.
    Do I hear you saying pulling one out of a Monte is easier?
    Didn't get to spend much time tonight, had to mow (1 acres), mower wouldn't start, bla, bla. Pulled the links and the mounts, but the curves were hitting between the engine and fire wall. On a 97 do you have to lower the engine cradle? If so are the bolts long enough or do I need to support it with a jack? Is that why you suggested the Monte for the u-pull-a-part?
    You said 00 plus, how far (upper year)?
    Thanks again.
    07 Grand Prix GXP (My Daily Driver and future toy) (120,000+)
    97 Grand Prix GT (Project Car) (178,000+)
    02 Mustang Convertible (Wife's Toy) (75,000+)
    17 Honda Civic (Wife's Daily Driver)
    Reply With Quote  
     

  20. #60 Re: 97 GP GT - Let's project a project car (from trailer to driving) 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,919
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    you dont "need" to lower the back of the frame but it adds some extra room to get the bolt on the driver side where all the brake lines snake past.

    montes should have a solid bar.

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

Page 3 of 5 FirstFirst 12345 LastLast

Similar Threads

  1. my little project
    By vincegpking in forum Members Rides
    Replies: 11
    Last Post: 10-02-2013, 10:19 AM
  2. Project car?
    By Ricky21 in forum Off Topic Discussion
    Replies: 4
    Last Post: 02-11-2011, 09:31 PM
  3. New Project
    By KawaFord in forum Off Topic Discussion
    Replies: 37
    Last Post: 04-22-2010, 10:54 AM
  4. next project
    By JarenSTi in forum Off Topic Discussion
    Replies: 38
    Last Post: 01-01-2010, 09:35 PM
  5. $200 gtp project
    By bwhicker649 in forum Introductions/Noob Questions
    Replies: 2
    Last Post: 11-27-2009, 10:04 PM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •