Comes with the territory. I'll be more careful next time.
Printable View
Comes with the territory. I'll be more careful next time.
http://img.tapatalk.com/d/13/06/29/my7ujydy.jpg
http://img.tapatalk.com/d/13/06/29/apumavus.jpg
http://img.tapatalk.com/d/13/06/29/uvy5uzuv.jpg
Selling what's left of the trans for $250 OBO. I can't use it.
looks a little cleaner, you should definetly replace the crank seal it is 10000000X easier when the motor is out
Ha yup! Took the front cover off and cleaned the heck out of it. Replaced every gasket except that back cover and rear main. They weren't showing signs of leaking and seemed OK so I left them alone.
More pictures of the destruction....
http://img.tapatalk.com/d/13/07/01/gu3u4utu.jpg
http://img.tapatalk.com/d/13/07/01/ane7uryh.jpg
http://img.tapatalk.com/d/13/07/01/pynupyme.jpg
The broken skirt on the opposite side of the chip.
http://img.tapatalk.com/d/13/07/01/a2a5y3uz.jpg
See all of the scoring on the cylinder walls on the left compared to the smooth on the right?
http://img.tapatalk.com/d/13/07/01/6y6eraru.jpg
http://img.tapatalk.com/d/13/07/01/vyju9a9a.jpg
The rod journal looks to be intact. The rod bearings didn't spin.
http://img.tapatalk.com/d/13/07/10/y5edy2em.jpg
That.....was a b**ch.
http://img.tapatalk.com/d/13/07/10/u4ugunur.jpg
I will be pulling an all nighter some time this week.
See LIM bolts down both ways.
Sent from my SPH-L720 using Tapatalk 4 Beta
I just want this ufcking nightmare to be over. I've seriously had it. It has been to ufcking long ufcking months. I finally hit the weekend where I could be driving this god damned car TONIGHT. if only my front exhaust header didnt bump against my head studs. Seriously? The rear went right on so what the ****ing ufck! They're even the same heads from my top swap. Ugh....
End ufcking rant
Sent from my SPH-L720 using Tapatalk 4 Beta
Well I drove around maybe 30mins.
There's a stumbling like with my last setup in right at the transition into boost. Can hear popping from the exhaust, hesitation...but 0kr on the scan.
Almost seems like it happens more on a gear change. Maybe torque management pulling something and the engine doesn't like it.
That's what destroyed the last engine so I'll be hunting this ghost down.
Sent from my SPH-L720 using Tapatalk 4 Beta
https://www.youtube.com/watch?v=KlbX...e_gdata_player
Sent from my SPH-L720 using Tapatalk 4 Beta
Perhaps fuel related or misfires because of the popping sound.
What PCM and tuning software are you using?
I'm still using hp tuners.
Sent from my SPH-L720 using Tapatalk 4 Beta
I'm never using a MAP sensor again.
Sent from my SPH-L720 using Tapatalk 4 Beta
http://img.tapatalk.com/d/13/09/10/ugeduteg.jpg
Apparent oil starvation issue from the L26. This is from #6 rod journal I believe. I loosened all of the rod caps and rotated thr crank around pulling pistons and found this bearing spun half way around but the tangs aren't shaved off.
Either way...no budget for machining. Closer and closer to giving up on her.
Sent from my SPH-L720 using Tapatalk 4
De-Mod
Sent from my SPH-L720 using Tapatalk 4
Damn sorry to hear that the engine swap didn't go as planned.
Yeah it happens. Back to basics and come back with an RWD V8.
Sent from my SPH-L720 using Tapatalk 4