Thread: 2007 supercharged Balancer repair sleeve? Front seal replacement

Results 1 to 7 of 7
  1. #1 2007 supercharged Balancer repair sleeve? Front seal replacement 
    GTP Level Member
    Join Date
    Jun 2016
    Location
    Cleveland ohio
    Posts
    890
    Thanks (Received)
    1
    Likes (Received)
    9
    Dislikes (Received)
    0
    I am getting ready to replace my front crankshaft seal and sensor on my 2007 Grand Prix supercharged series III. Does anyone know if there is a balancer repair sleeve for this model? I searched and did not find much on this. I want to have one on hand just in case there is a groove on the balancer when I get it off. Also any tips or videos on how to install the sleeve if there is one. Any help is appreciated.

    Thanks
    2017 Buick Regal 2.0 Turbo (SOLD 2007 Grand Prix GT. Front and rear PLOGs, 1.8 roller rockers, CAI, HPTuned, 3.4 pulley, TEP transmission, 90# springs, rollmaster single chain, Impala front brakes d/s rotors.) Past (Pontiacs) Grand Prix- 97 GT, 03 GT, 04 GT, 04 Comp G, 78 Trans am, 92 Trans Am.
    Reply With Quote  
     

  2. #2 Re: 2007 supercharged Balancer repair sleeve? Front seal replacement 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,919
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    see if these links work, this was for my 98 regal, see if the seal part # is the same, then it should work.

    https://hosting.photobucket.com/albu...psashf10yn.jpg

    https://hosting.photobucket.com/albu...psjo9t0y7k.jpg

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  3. #3 Re: 2007 supercharged Balancer repair sleeve? Front seal replacement 
    GTP Level Member
    Join Date
    Jun 2016
    Location
    Cleveland ohio
    Posts
    890
    Thanks (Received)
    1
    Likes (Received)
    9
    Dislikes (Received)
    0
    Doesn’t look like it is the same. I don’t see a front skf seal # for mine.
    Reply With Quote  
     

  4. #4 Re: 2007 supercharged Balancer repair sleeve? Front seal replacement 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,919
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    it could be any brand crank seal. if they are the same the balancer part should be the same size.

    the parts store i got that at used to be a napa, now a car quest, so they still had the " books" , where they found it, then had to order it.

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  5. #5 Re: 2007 supercharged Balancer repair sleeve? Front seal replacement 
    GTP Level Member
    Join Date
    Jun 2016
    Location
    Cleveland ohio
    Posts
    890
    Thanks (Received)
    1
    Likes (Received)
    9
    Dislikes (Received)
    0
    I looked up the harmonic balancer again on Rock Auto and decided just to get a new balancer just to be safe. It was cheap enough ($77) just to have piece of mind.
    Reply With Quote  
     

  6. #6 Re: 2007 supercharged Balancer repair sleeve? Front seal replacement 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,919
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    if you bought it, use it, these balancers do fail with age. mine did at 243k.

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  7. #7 Re: 2007 supercharged Balancer repair sleeve? Front seal replacement 
    GTP Level Member
    Join Date
    Jun 2016
    Location
    Cleveland ohio
    Posts
    890
    Thanks (Received)
    1
    Likes (Received)
    9
    Dislikes (Received)
    0
    Definitely will then. Mine has 217k
    Reply With Quote  
     

Similar Threads

  1. Snout seal replacement.
    By Deno in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 6
    Last Post: 06-02-2020, 09:00 AM
  2. Front seal replacement
    By alenw62 in forum 1997-2007 4 speed Automatic (4T65E) (4T65E-HD)
    Replies: 1
    Last Post: 11-19-2016, 08:10 PM
  3. Front seal replacement
    By mechanicboy in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 12
    Last Post: 01-11-2016, 08:45 AM
  4. Front Oil Seal Leaking after replacement again..HELP
    By timboku in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 9
    Last Post: 01-12-2014, 12:24 PM
  5. New Front Crank Oil Seal Leaking - Grooved Balancer?
    By Scott Kane in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 2
    Last Post: 12-08-2010, 03:58 PM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •