blew my exhaust pipe off, down pipe and res dropped and dragged for 2 blocks till i could find a clear spot to park and put it back together.
looking into a band clamp for it now, normal clamps keep failing me.
|
|
02-14-2014
blew my exhaust pipe off, down pipe and res dropped and dragged for 2 blocks till i could find a clear spot to park and put it back together.
looking into a band clamp for it now, normal clamps keep failing me.
02-14-2014
Was gonna wash it but then..
Sent from my HTC Thunderbolt using Tapatalk
02-14-2014
Since its like 80+ here I decided to get the laughing gas installed.
02-14-2014
Arizona seems like a nice place to live
02-14-2014
Found me a l67 motor with 92k miles 400 dollars pulling it out and taking it home to swap out my 189k mile l67 couldn't pass up the deal.. just hope it fits BC it out of a Buick park avenue ultra
Taz238
02-14-2014
My full set of GR-2s arrived today (rock auto got them here in two days). Waiting on strut mounts and 3 inch DP from ZZP...which shipped today.
02-14-2014
RSTB is in.
Along with new poly bushings for the dog bones. This one was really bad.
02-14-2014
Dang ^ flipping them almost always firms them back up, but that thing is destroyed. You must be a big lead foot or something lol
02-14-2014
Did a few pulls today and felt like a honda spinning though gears... so a few moments ago i broke down and bought some new DR's and new rear tires since i was peeling money out of my wallet.
02-14-2014
I'm still healing up from doing my own lolOriginally Posted by Schmidty
Sent from my Galaxy Note 3
02-15-2014
The driver side looked fine. Now that I replaced the lower ones with poly. I think I should do the upper round ones as well.
02-15-2014
Got a new ign. module because of skipping only find it runs worse & dies. Took it to Chevy mech. and they flashed modules, cleaned the MAF sensor & throttle body.
Picked it up and still skips at part throttle so gotta pedal it like a dragster. Eng. light is back on.
It's had a trans. shop check for issues. My mech. put a new fuel filter on & the ign. module. Fuel pressure is ok. Has 170k miles on it.
Plugs were done about 100k miles. Getting new wires on Monday & thinking of plugs too while they're at it.
I usually do this **** but my back went out with the XMas paper and it's winter so we're screwed.
Is it a sensor or what's the problem?.!
-- Sent with :banghead:
02-15-2014
go to a autozone parts store, they will scan it for free.
or buy a cheap scanner, i got one shipped for 16 bucks. i got sick of waiting on line for the free scan.
or if you have a droid phone you can get the torque app for your phone $5 for the app, $15 for the obd2 blue tooth.
02-15-2014
Yep second the suggestion for the Bluetooth dongle and torque app... it's helped me diagnose plenty of cars...
Sent from my Galaxy Note 3
02-15-2014
We have a Craftsman 9 87702 CanOBD2 code reader. Guess I gotta get outside and see. It's an assload of snow outside.
-- Sent with :-)
02-15-2014
the code holds the answer 99% of the time.
02-15-2014
Currently driving back from meeting a guy on cl with my new sd hood!
Originally Posted by BoostenGTP
02-15-2014
I dug the Grand Prix out (again)
Snapped a pic of Stealth while I was out there
02-15-2014
The funny thing is there were no codes until after a replacement ign. ctrl. module was put in and it died all over town. Then Mr. Goodwrench flashed some **** and it still sputters but it doesn't die at least. We've been digging out and the plow guy is out there now.
THANKS!
-- Sent with :-)
02-15-2014
My power steering was starting to make just a little bit of a whining sound on the way home, I bet the reservoir is going low again, I'm gonna go out and check it and top it off with lucas again.
Also stealthee your shed is identical to mine. Ours is a bit custom with gutters and electricity but it's the same lol.
| « Previous Thread | Next Thread » |
| Tags for this Thread |
| Bookmarks |
Bookmarks |
