Thread: Cleaning Parts

Results 1 to 16 of 16
  1. #1 Cleaning Parts 
    GT Level Member tdm571's Avatar
    Join Date
    Mar 2010
    Location
    Lakeside Park, KY
    Posts
    311
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    I just found a nice 97 GTP in the junk yard. Engine is pretty decent and intact. I'm gonna grab all the parts for a top swap for my 97 SE. This is my spare/play vehicle so I'm gonna take my time and try to be pretty meticulous. What is the recommended way of cleaning all the parts (heads, intake, SC, fuel rail/injectors, TB, etc)? Also, which parts can be painted? Should I use POR-15 on anything?
    Reply With Quote  
     

  2. #2 Re: Cleaning Parts 
    The Blue One blueguy's Avatar
    Join Date
    Jun 2008
    Location
    Dirtyzville, Missery
    Posts
    31,287
    Thanks (Received)
    1
    Likes (Received)
    2
    Dislikes (Received)
    0
    Hope you pick up the transmission out of it too...because your '97 vacuum power trans is gonna last through maybe one WOT run before it turns to dust. Cleaning parts though...I use Chem-dip.
    Sold WBody's: '03 Blue GTP/'98 Green GTP/'98 Silver GT/'05 GXP
    '99 Chevrolet Silverado Classic Z71 4x4 - K&N Intake/Gibson Exhaust #TRUCKTHINGS
    '12 Buick Regal Turbo - ZZP CAI/20% Tint/HID's
    '89 Ford Mustang LX Notchback - LM7 5.3, 4L80, 9", HX40
    '04 Chevrolet Corvette MRM A4/LS1 - TSP LT's, 3"O/R X, AFE S2 CAI
    Reply With Quote  
     

  3. #3 Re: Cleaning Parts 
    GT Level Member tdm571's Avatar
    Join Date
    Mar 2010
    Location
    Lakeside Park, KY
    Posts
    311
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Can a simple weekend warrior get enough chem-dip to clean the supercharger and intake manifold? I don't see a 5-gal being big enough to soak them in.
    Reply With Quote  
     

  4. #4 Re: Cleaning Parts 
    The mod from over yonder TheOtherNick's Avatar
    Join Date
    Sep 2008
    Location
    Charles City, IA
    Posts
    9,955
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Buy a parts washer for like $150 then you are golden.
    01 gtp-big cam e85 dd 78dodge- guzzling fuel 05 cummins- rollin coal
    SMGPFC Two Nipple General
    Reply With Quote  
     

  5. #5 Re: Cleaning Parts 
    GT Level Member tdm571's Avatar
    Join Date
    Mar 2010
    Location
    Lakeside Park, KY
    Posts
    311
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    If I used chem-dip on the supercharger or the heads, what would I have to replace? I'm sure there is stuff that won't survive.
    Reply With Quote  
     

  6. #6 Re: Cleaning Parts 
    The Blue One blueguy's Avatar
    Join Date
    Jun 2008
    Location
    Dirtyzville, Missery
    Posts
    31,287
    Thanks (Received)
    1
    Likes (Received)
    2
    Dislikes (Received)
    0
    I pour it into an old Windex bottle and spray away...it works.
    Sold WBody's: '03 Blue GTP/'98 Green GTP/'98 Silver GT/'05 GXP
    '99 Chevrolet Silverado Classic Z71 4x4 - K&N Intake/Gibson Exhaust #TRUCKTHINGS
    '12 Buick Regal Turbo - ZZP CAI/20% Tint/HID's
    '89 Ford Mustang LX Notchback - LM7 5.3, 4L80, 9", HX40
    '04 Chevrolet Corvette MRM A4/LS1 - TSP LT's, 3"O/R X, AFE S2 CAI
    Reply With Quote  
     

  7. #7 Re: Cleaning Parts 
    GT Level Member tdm571's Avatar
    Join Date
    Mar 2010
    Location
    Lakeside Park, KY
    Posts
    311
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    The chem-dip won't eat away at the windex bottle?
    Reply With Quote  
     

  8. #8 Re: Cleaning Parts 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,815
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    Clean the outside of the charger only. Inside the compression chamber and the needle bearings you don't want to mess with. Cleaning the compression chamber will only mean it won't seal up as well.

    Clean the LIM with purple power or simple green.

    Clean the heads with some brake cleaner. Wipe of excess first than then finish them up.

    Nick.. you suggesting he grab the 4T65 and transplant into a 4T60 car?
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  9. #9 Re: Cleaning Parts 
    GT Level Member tdm571's Avatar
    Join Date
    Mar 2010
    Location
    Lakeside Park, KY
    Posts
    311
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Even though it's all black inside the supercharger? The heads I don't feel as bad about dipping. I'm already working on the tranny exchange.
    Reply With Quote  
     

  10. #10 Re: Cleaning Parts 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,815
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    The heads will accept dipping.. I'd leave as much oil on them until you plan to use them though. Cast iron can rust easily with any moisture.

    On the charger.. I'm only saying compression chamber. If you pull the rotors and tape over the bearings.. then go ahead on the inlet and port it to clean.. but don't clean the compression chamber. That crud exists with the rotors and helps them seal for better performance.
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  11. #11 Re: Cleaning Parts 
    GT Level Member tdm571's Avatar
    Join Date
    Mar 2010
    Location
    Lakeside Park, KY
    Posts
    311
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Quote Originally Posted by BillBoost37 View Post
    The heads will accept dipping.. I'd leave as much oil on them until you plan to use them though. Cast iron can rust easily with any moisture.
    I thought the heads were alluminum.
    Reply With Quote  
     

  12. #12 Re: Cleaning Parts 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,815
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    Our 3.8L motors have cast iron heads.
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  13. #13 Re: Cleaning Parts 
    GT Level Member tdm571's Avatar
    Join Date
    Mar 2010
    Location
    Lakeside Park, KY
    Posts
    311
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    What about the 97 GTP?
    Reply With Quote  
     

  14. #14 Re: Cleaning Parts 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,815
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    I'm confused. You mentioend it was a 97 GTP in the first post. Which means it has a 3.8L supercharged motor.

    All 3.8L GM motors from 87-08 have cast iron heads. BTW..each head without rockers will weight ~35lbs.
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  15. #15 Re: Cleaning Parts 
    The Blue One blueguy's Avatar
    Join Date
    Jun 2008
    Location
    Dirtyzville, Missery
    Posts
    31,287
    Thanks (Received)
    1
    Likes (Received)
    2
    Dislikes (Received)
    0
    It's the same as any other 3800 car.

    Cast iron. The Alummy heads weigh a max of 20 pounds fully assembled last I checked. And ya...I suggested he swap the 4T65E into his 4T60E car...because we all know how well the vacuum transmission holds up to modding.

    It doesn't.
    Sold WBody's: '03 Blue GTP/'98 Green GTP/'98 Silver GT/'05 GXP
    '99 Chevrolet Silverado Classic Z71 4x4 - K&N Intake/Gibson Exhaust #TRUCKTHINGS
    '12 Buick Regal Turbo - ZZP CAI/20% Tint/HID's
    '89 Ford Mustang LX Notchback - LM7 5.3, 4L80, 9", HX40
    '04 Chevrolet Corvette MRM A4/LS1 - TSP LT's, 3"O/R X, AFE S2 CAI
    Reply With Quote  
     

  16. #16 Re: Cleaning Parts 
    SE Level Member RustyHO's Avatar
    Join Date
    May 2011
    Location
    Havelock
    Posts
    11
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    i just took the heads off my scrap car, and ya there prolly closer to 35 pounds lol
    Reply With Quote  
     

Similar Threads

  1. cleaning up the outside
    By crshoveride in forum General Tech Discussion
    Replies: 12
    Last Post: 06-03-2011, 09:09 AM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •