Thread: Need some advice...

Page 1 of 3 123 LastLast
Results 1 to 20 of 47
  1. #1 Need some advice... 
    GrandPrix Junkie
    Join Date
    Mar 2012
    Location
    NC
    Posts
    3,264
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    454
    So, my 200s is dirty...like super dirty. I told it not to be, but I guess it just has a filthy mind. Anyway, I need to give it a bath and a really good detail. I'm looking for recommendations on products to use, how to use them, and approximate prices to make it all shiny and purdy again (everything from car wash to wax to clay bar to tire protector etc). Any help?
    Reply With Quote  
     

  2. #2 Re: Need some advice... 
    GT Level Member Xorbex's Avatar
    Join Date
    Jul 2009
    Location
    Canada
    Posts
    293
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    2445
    I used mcguires claw bar but be prepared to know and hate the paint job. Also use stuff called "liquid glass" after washing. Its super easy to put on and remove and it is fast and leaves a beautiful shine. It goes on and rubs off almost immediately in a fine powder. BE CAREFUL do not get this stuff on your plastic headlights of youll end up sanding it off like i did.
    RIP August 2015 - (2005 Comp G // Custom HAI / S1X Cam / 105 Crow Springs / Mild Ported heads / 3.4 Pulley / SD Headers / Dynomax Catback / Overkill Tune / Comp cams pushrods / LS7 Lifters //)
    Reply With Quote  
     

  3. #3 Re: Need some advice... 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,833
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    Chats
    98246
    Hop on autogeek.net and read up on the how to's.

    Start off with good products. There is no replacement for good quality products.
    Two wash buckets
    If needing to claying, then strip the wax (if any) with dish detergent
    After clay, I think it's a water/isopropyl mix to remove all clay residue
    Then since it's new.. (watch more vids) buff with probably a light cutting compound/pad Can't hurt a thing with a PC XP 7424, it's the choice of champions
    http://www.autogeek.net/po.html
    Then a final polish with the PC
    A sealant
    And a wax
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  4. #4 Re: Need some advice... 
    GrandPrix Junkie
    Join Date
    Mar 2012
    Location
    NC
    Posts
    3,264
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    454
    Quote Originally Posted by BillBoost37 View Post
    Hop on autogeek.net and read up on the how to's.

    Start off with good products. There is no replacement for good quality products.
    Two wash buckets
    If needing to claying, then strip the wax (if any) with dish detergent
    After clay, I think it's a water/isopropyl mix to remove all clay residue
    Then since it's new.. (watch more vids) buff with probably a light cutting compound/pad Can't hurt a thing with a PC XP 7424, it's the choice of champions
    http://www.autogeek.net/po.html
    Then a final polish with the PC
    A sealant
    And a wax
    Keep in mind this is my first new car in over a decade...and I'm still poor. Back when I purchased my previous new vehicles, I had money to pay for professional detailing so I've never had to do it. Thus, I have no idea how to buff or even wtf sealing paint is. LOL
    Reply With Quote  
     

  5. #5 Re: Need some advice... 
    GT Level Member Xorbex's Avatar
    Join Date
    Jul 2009
    Location
    Canada
    Posts
    293
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    2445
    What Bill described is the proper way to do it but i've had FANTASTIC results in doing it with liquid glass. Ive also done the like 5-6 step buff n crap and was less satisfied. That being said its up to you but from experience wash, clay bar (even if brand new), wash clay bar residue off, dry, apply liquid glass and remove. No buffing required the stuff comes off super easy with a lint free cloth. You wont even need any elbow grease except the clay bar part.
    RIP August 2015 - (2005 Comp G // Custom HAI / S1X Cam / 105 Crow Springs / Mild Ported heads / 3.4 Pulley / SD Headers / Dynomax Catback / Overkill Tune / Comp cams pushrods / LS7 Lifters //)
    Reply With Quote  
     

  6. #6 Re: Need some advice... 
    GrandPrix Junkie
    Join Date
    Mar 2012
    Location
    NC
    Posts
    3,264
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    454
    Quote Originally Posted by Xorbex View Post
    What Bill described is the proper way to do it but i've had FANTASTIC results in doing it with liquid glass. Ive also done the like 5-6 step buff n crap and was less satisfied. That being said its up to you but from experience wash, clay bar (even if brand new), wash clay bar residue off, dry, apply liquid glass and remove. No buffing required the stuff comes off super easy with a lint free cloth. You wont even need any elbow grease except the clay bar part.
    This method seems appealing since I'm a lazy fvck. LOL
    Reply With Quote  
     

  7. #7 Re: Need some advice... 
    GT Level Member Xorbex's Avatar
    Join Date
    Jul 2009
    Location
    Canada
    Posts
    293
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    2445
    I dont have the knowledge as someone like bill so maybe my way is wrong but it hasn't failed me. Maybe some other members can give advice.
    RIP August 2015 - (2005 Comp G // Custom HAI / S1X Cam / 105 Crow Springs / Mild Ported heads / 3.4 Pulley / SD Headers / Dynomax Catback / Overkill Tune / Comp cams pushrods / LS7 Lifters //)
    Reply With Quote  
     

  8. #8 Re: Need some advice... 
    GrandPrix Junkie
    Join Date
    Mar 2012
    Location
    NC
    Posts
    3,264
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    454
    Quote Originally Posted by Xorbex View Post
    I dont have the knowledge as someone like bill so maybe my way is wrong but it hasn't failed me. Maybe some other members can give advice.
    I certainly appreciate the input and will definitely look into it. I'm trying to learn as much as I can from people who have used products so I can do this myself and keep my new car looking purdy.
    Reply With Quote  
     

  9. #9 Re: Need some advice... 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,833
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    Chats
    98246
    Results speak for themselves, I've had friends like Mechanic Dan accuse me of having cars repainted. All from a bit of time behind an orbital random buffer.


    How it arrived


    I did a quick job on this.. and here's how it transformed




    It only got better from there.
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  10. #10 Re: Need some advice... 
    The Blue One blueguy's Avatar
    Join Date
    Jun 2008
    Location
    Dirtyzville, Missery
    Posts
    31,287
    Thanks (Received)
    1
    Likes (Received)
    2
    Dislikes (Received)
    0
    Chats
    77762
    Do it right maaaan.

    I detailed for a couple years on the side.

    Clay bar is damn near a need, not a want. Especially on a new car that has all the residue from the factory.

    Brand new cars sometimes are straight awful.
    Sold WBody's: '03 Blue GTP/'98 Green GTP/'98 Silver GT/'05 GXP
    '99 Chevrolet Silverado Classic Z71 4x4 - K&N Intake/Gibson Exhaust #TRUCKTHINGS
    '12 Buick Regal Turbo - ZZP CAI/20% Tint/HID's
    '89 Ford Mustang LX Notchback - LM7 5.3, 4L80, 9", HX40
    '04 Chevrolet Corvette MRM A4/LS1 - TSP LT's, 3"O/R X, AFE S2 CAI
    Reply With Quote  
     

  11. #11 Re: Need some advice... 
    GrandPrix Junkie
    Join Date
    Mar 2012
    Location
    NC
    Posts
    3,264
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    454
    Quote Originally Posted by BillBoost37 View Post
    Results speak for themselves, I've had friends like Mechanic Dan accuse me of having cars repainted. All from a bit of time behind an orbital random buffer.


    How it arrived


    I did a quick job on this.. and here's how it transformed




    It only got better from there.
    You're welcome to come teach me Bill. LOL
    Reply With Quote  
     

  12. #12 Re: Need some advice... 
    GrandPrix Junkie
    Join Date
    Mar 2012
    Location
    NC
    Posts
    3,264
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    454
    Quote Originally Posted by blueguy View Post
    Do it right maaaan.

    I detailed for a couple years on the side.

    Clay bar is damn near a need, not a want. Especially on a new car that has all the residue from the factory.

    Brand new cars sometimes are straight awful.
    I want to do it right, but I'd prefer someone to teach me the in's and out's...
    Reply With Quote  
     

  13. #13 Re: Need some advice... 
    GrandPrix Junkie HighOctaneRacing's Avatar
    Join Date
    Jan 2011
    Location
    Enfield, CT
    Posts
    3,360
    Thanks (Received)
    1
    Likes (Received)
    1
    Dislikes (Received)
    1
    Chats
    8962
    Quote Originally Posted by Sven The Baldman View Post
    I want to do it right, but I'd prefer someone to teach me the in's and out's...
    Me too lol
    Reply With Quote  
     

  14. #14 Re: Need some advice... 
    GrandPrix Junkie spazzz's Avatar
    Join Date
    Nov 2012
    Location
    Madison
    Posts
    3,328
    Thanks (Received)
    3
    Likes (Received)
    8
    Dislikes (Received)
    0
    Chats
    0
    Ultimate Polish and maybe Ultimate compound for more severe dealer swirls.M205 if you can snag it

    A DA AND LAKE COUNTRY PADS.

    Fn decent microfibers......only good ones 360gsm+.
    Chenille wash mitt or two.
    Waffle weave drying towel

    Meguiars Ultimate Wax is an excellent over the counter.......easily as good as any boutique wax.....or some Collinite 845.....2 durable sealant/waxes.
    Don't fall for the Carnauba label on bottles.

    P.M. the GUZ>>>>right the hell now.


    Clay......2 buckets with grit guards and kiss a day away.
    Reply With Quote  
     

  15. #15 Re: Need some advice... 
    GrandPrix Junkie idrivejunk's Avatar
    Join Date
    Jan 2014
    Location
    AR
    Posts
    4,899
    Thanks (Received)
    4
    Likes (Received)
    32
    Dislikes (Received)
    1
    Chats
    0
    Well, the non-descriptive post title didn't really draw me in so I'm late. But I've done lots of paint / body / detail work. Tips I give will be more general, less specific. Geared towards retaining resale value. Meguiar's is my favorite paint care product manufacturer by a long shot. I use a cheap rotary polisher like body shops have, for my buffing work.

    WORK with the wash mitt / pad / cloth. Be thorough, use multiple passes everywhere. Bend down if needed, lol. Amazing how folks just won't do that. Keep it clean and concentrate on doing honest cleaning. Don't just leave a stubborn spot and think its a reason for more fancy chemistry if scrubbing a few more passes takes it off.

    Don't be hesitant to do a small amount of disassembly to clean some areas periodically. Actually lift the wipers and scrub the cowl and wipers, etc.

    Dedicate a mitt to wheelwells and engine compartment.

    Always mitt the jambs. Always mitt and wipedown under the hood.

    Remove alloy wheels and clean the backside once or twice a year, esp fronts.

    CAREFUL with clay. WATCH what you're doing, knead often and chunk when dirty. Use a lubricant with clay, as recommended. Use the least agressive clay that does the job.

    Remember to use a proper solvent such as wax and grease remover for grease / tar / undercoat. WD40 gently if you run through road construction tar.

    New cars are yes- usually badly contaminated since they are around rail yards and hot steel dust plus fallout and nature. Do a diligent but gentle clay job on the new car, and repeat yearly at a minimum on top surfaces.

    My approach once the paint is clean, is to use cheap wax first then expensive on top. I'm not much into waxing but don't really have fine paint on anything. I still prefer a good old cotton t shirt for final wiping of things.

    Stay on the chips with touch up paint religiously and get good at doing nice dabs that don't stand out. Do it AFTER wax to avoid the white edges. If it comes off you can always re-touch it.

    Tire shine? Eagle has been the only brand that stands out in my experience. Their brush-on (foam applicator) product (Extreme?) impressed me as far as how long it lasts as opposed to spray-on products.
    All Grand Prix, all the time. 69 Model J, 99 GT & GTP coupes. All junk, haha.
    Reply With Quote  
     

  16. #16 Re: Need some advice... 
    GrandPrix Junkie The Guz's Avatar
    Join Date
    Dec 2008
    Location
    Lawndale, CA
    Posts
    3,007
    Thanks (Received)
    3
    Likes (Received)
    9
    Dislikes (Received)
    0
    Chats
    0
    I always recommend this kit for those starting out on their own. It comes with everything you need. It's an online kit only.

    http://www.walmart.com/ip/Meguiar-s-...undle/29670206

    The first question is are you going to do this by machine or by hand? The reason I ask is because if the car has deep defects, you will not be able to remove them by hand. You will make it look better but a dual action polisher is the way to go. Plus it saves you time and your arms.

    New cars can have just as many surface contaminants as any car. Who knows how long it's been sitting on the dealer lot exposed to the elements. You also have rail dust from it being delivered. So I always recommend to clay. It will allow the wax or sealant to bond to the paint and last longer.

    Also did you let the dealer wash and detail the car prior to you getting it? There have been lots of horror stories of the so called DISO (Dealer Installed Swirl Option). Go outside in the sun and look at the car. If you have swirls then you are in for some work.

    For example this is what the body shop did to my brothers car. They hammered the finish and it took some work to remove them by machine.





    Here's the typical 5 step detail process. I will use the products in the link I provided.

    1. Wash - Use the provided soap in the kit Ultimate Wash & Wax to wash the car. The dilution ration is 1 oz per 1 gallon of water.

    2. Clay - I recommend you pick up the Meguiar's Clay kit. It's available locally. A quick tip on how to tell if you need to clay or not is to use the baggie test. Google baggie test and you will see how to do it.

    If the car looks good to you and you are happy with the way it looks then proceed to sealing the car with Meguiar's Ultimate Wax. This is a synthetic wax also known as a sealant. They are intended to last longer than a carnauba wax. Don't let the term wax fool you. It was placed there for pure marketing by Meguiar's as an average joe doesn't know what a sealant is.

    My first tip is to do a test spot with the least aggressive combination. In this instance Ultimate Polish. If you are happy with the finish

    3. Compound - Depending on the test spot you may need to go to an aggressive product. You would use ultimate compound on each individual panel. Don't let it dry. Work it in with a little pressure. Not too much or you will get cheetah spots if you are doing this by hand. Ultimate Compound can finish very well that you can seal the paint right after.

    http://www.meguiarsonline.com/forums...my-paint!-quot

    4. Polish - Depending on your test spot you can either proceed if you are satisfied with finish or you follow up after using ultimate compound. This may be an optional step if ultimate compound finished very well. A polish will give you the gloss.

    5. Protection - Use the ultimate wax within the kit and seal the paint. Good video to watch if you go with this kit.

    http://www.meguiarsonline.com/forums...ion-Experience

    6. Maintain - I would pick up some ultimate quik wax and use it every other wash. It is a spray wax that is intended to boost ultimate wax. It will extend the life of it and give you that shine until your next waxing session. You also want to practice good washing techniques.

    http://www.meguiarsonline.com/forums...Series-Washing

    If you are going to be using a dual action polisher then I will provide you with some good pads to get.

    For tires I like to use either Meguiar's D163 Tire & Trim Gel. It's a water based gel dressing. It is from their detailer line and is only available online. The other Meguiar's product that works very well is Meguiar's Ultimate black tire coating. If you want gloss then this product is not for you. It's an aerosol based product so you will get overspray like any aerosol product on the wheels. Be sure to have a microfiber in hand and remove the residue before it dries. It will leave the tire black with a hint of sheen. If you are looking for something that lasts longer then I would recommend the turtle wax jet black black endura shine tire coating.

    If there is any plastic trim, be sure to protect it right away. The kit comes with ultimate black which is decent for an over the counter product. I recommend you prep the surface by cleaning it really good. You can either invest in some Meguiar's D101 All Purpose Cleaner or purchase the Mothers Heavy Duty Trim Cleaner Kit. Use it to prep the surface and follow up with the time protectant. By cleaning and prepping the trim it will allow the trim protectant to bond to the plastic and last longer.

    That should keep your exterior looking good. The only other thing I would recommend is to pick up some more microfibers and some more drying towels.
    1999 GP GT 18" Boss 353 Concave|SLP CAI|Borla Cat Back|Plog|HV3|HV TB|ER Rockers|Custom Retrofit Projectors|GMPP Lowering|GMPP Handling|MPD F1|Full Diode Dynamic LEDs
    Reply With Quote  
     

  17. #17 Re: Need some advice... 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,995
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    Chats
    243824
    i know jays cheap like me lol this is low budget turtle wax liquid compound and then turtle wax, wax. all done with a pc d/a orital buffer.

    this was my first time ever using one too.

    before.



    after.



    after a bath before the buffer. the paint was rather dead, i had no idea it could come back to life with a little work and 20 bucks in product that has lasted 5 years so far lol



    after




    i kinda refuse to pay for top of the line products when the good old fashioned cheap crap works just fine. i wax it 2 times a year, compound when it looks like it needs it, aka lots of swirl marks. the turtle will last a year too. even after this winter it still shinned and beaded water like it was just waxed when it got a bath.

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  18. #18 Re: Need some advice... 
    Turbo is the way to go. REDCRAPGP's Avatar
    Join Date
    Aug 2009
    Location
    Behind you...sike made you look Bish
    Posts
    16,085
    Thanks (Received)
    0
    Likes (Received)
    1
    Dislikes (Received)
    0
    Chats
    78
    ^ I can't notice the difference





    But it must be cause it's a Regal and they always look bad




    Sent from my iPhone using Tapatalk
    Squirrels are my engine. I need a Ford Regal
    04 Comp G.
    Reply With Quote  
     

  19. #19 Re: Need some advice... 
    GXP Level Member Timing's Avatar
    Join Date
    Feb 2012
    Location
    gardner,mass
    Posts
    2,141
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    4583
    Quote Originally Posted by Sven The Baldman View Post
    So, my 200s is dirty...like super dirty. I told it not to be, but I guess it just has a filthy mind. Anyway, I need to give it a bath and a really good detail. I'm looking for recommendations on products to use, how to use them, and approximate prices to make it all shiny and purdy again (everything from car wash to wax to clay bar to tire protector etc). Any help?
    I have used every product i have on the shelf at my work and the Meguiars Ultimate line is by far the closest to top tier stuff i have ever used. The compound polish and i prefer the paste wax is stunning and applies so easy.
    08 MazdaSpeed 3- Treadstone tr8l, Ebay Piping, Ported intake,Thermal gasket, Cs Injector Seals,Cobb intake/inlet, Autotech Internals, Poly mounts, Speed Daddy DP, Magnaflow CB,
    RPF1 17x9 255/45 Direzza Zll
    04 COMPG- Vs, getrag 284 RIP
    Reply With Quote  
     

  20. #20 Re: Need some advice... 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,995
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    Chats
    243824
    Quote Originally Posted by REDCOMPG View Post
    ^ I can't notice the difference





    But it must be cause it's a Regal and they always look bad




    Sent from my iPhone using Tapatalk
    your also blind.......

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

Page 1 of 3 123 LastLast

Similar Threads

  1. Need E85 advice please
    By Ultra440 in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 24
    Last Post: 10-08-2012, 07:09 PM
  2. GXP advice?????
    By FatDog in forum Off Topic Discussion
    Replies: 15
    Last Post: 10-24-2010, 11:34 PM
  3. Need Advice
    By Amberella06 in forum Introductions/Noob Questions
    Replies: 4
    Last Post: 07-26-2010, 10:01 AM
  4. Need Some Advice
    By Traeger2591 in forum 3.8L V6 Naturally Aspirated (L36)(L26)
    Replies: 29
    Last Post: 01-16-2010, 12:18 PM
  5. I'm the New Guy, Looking for Advice
    By 98 DAYTONA in forum Introductions/Noob Questions
    Replies: 2
    Last Post: 06-04-2009, 09:47 AM
Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •