Thread: Replacing wheel bearing

Results 1 to 6 of 6
  1. #1 Replacing wheel bearing 
    SE Level Member
    Join Date
    Jan 2008
    Posts
    92
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    What tools are needed to replace a wheel bearing? Do you need a puller or no? I probabaley don't have all the tools but anybody around cleveland ohio think they can replace one for me? Most shops charge like $60-75 to do these things and its ridiculous.
    Reply With Quote  
     

  2. #2 Re: Replacing wheel bearing 
    GT Level Member BackInBlack's Avatar
    Join Date
    Dec 2007
    Location
    Vermont
    Posts
    335
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    Nothing too special. Sockets & extensions mostly. You probably should use a puller for the hub. I replaced a front one not too long ago, now the other one is howling at me. Got the lifetime warrantied one from ZZP for $70-something. I set the suspension back down on a pile of 4x4s to keep the control arm straight. Helps a LOT with managing the axle shaft. Keep some penetrating oil and a torch close by as well. Don't forget your fire extinguisher...
    The GPs are long gone...
    Reply With Quote  
     

  3. #3 Re: Replacing wheel bearing 
    GTP Level Member speedemongtp's Avatar
    Join Date
    Jun 2008
    Location
    Ohio
    Posts
    1,431
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    i just did both fronts this weekend. Have a ratchet some sockets extentions and a torque wrench. youll need a 10mm for the brakes a 14mm an i believe the other one i needed was a 12 or 13. 33 mm is what fit the ale nuts best for me but these are after market shafts cause i just replaced them several months ago.Its pretty easy job. Compress the piston. pull out the 2 14 mm an pull the whole break assembly off. then pull the rotor off. next you will have to pull out the 3 bolts in the back holding on the hub. these bolts will probably be pretty tight an a bit difficult but you will be able to get them. you will def want some penetrating oil of somesort thongh. then unplug the abs sensor now you will need a hammer to knock the old hub assembly off. this will take you a few minutes. then use some sand paper to clean up the inside of the hole then clean the face off as well. be sure to save the metal plate thats behind the huib you will need thes for the new one as well to hold the abs plugs like before. once youy have done that clean it all up then do everything in reverse order to replace it. you shouldnt need a hammer or anything to put in the new hubs. torque the axle nuts to 175 ftlbs. be sure to put antiseeze on the bolts when going back together as its always good to use. dont put it on the axle nut though. instead use some blue locktite so that it wont back itself off. once your done with all that bleed your breaks put your wheel back on torque your lugs an your good to go.
    00 GTP demodded and forsale
    Reply With Quote  
     

  4. #4 Re: Replacing wheel bearing 
    GTP Level Member speedemongtp's Avatar
    Join Date
    Jun 2008
    Location
    Ohio
    Posts
    1,431
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    ha i neglected to tell you to take the axle nut off. take that off before you take the bolts out of the back of the hub.
    00 GTP demodded and forsale
    Reply With Quote  
     

  5. #5 Re: Replacing wheel bearing 
    Donating Users GeddyLee's Avatar
    Join Date
    Dec 2007
    Location
    St. Louis Mo.
    Posts
    2,573
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    35
    Also be sure to use some antiseize on the axel bolt as well. It will make any future removals a breeze. Replacing the hub on our cars is actually one of the more easier things to remove.

    There are two methods to remove the axel nut. One is to take the center cap out of your wheel to access the hub nut with the vehicle's wheels on the wheel on the ground to being the removal of the nut. And the other is us a very long and thick bladed screw driver wedged into the brake rotor veins and propped against the car as leverage while jacked up to remove the axel bolt.

    Just thought I would drop that in there for ya.

    James Shafer
    2003 GP GTX SLP P/N 50066 (SOLD )
    2005 Nissan Pathfinder SE 4x4 (The baby hauler )
    St. Louis MO
    1.9 Modified Rockers, TOGs, 180 Tstat, PRJ 10.4 Wires, P/P Gen 3, SLP Ram Air Hood/Wizaired CAI, Gen 1 Spoiler, 3.4 ZZP Pulley, Desert Fox Tranny Cooler, Thrasher Shift Kit, 18" TSW Mondellos w/ AGX Struts, SSC Gen II Springs
    Reply With Quote  
     

  6. #6 Re: Replacing wheel bearing 
    SE Level Member daniel981's Avatar
    Join Date
    Oct 2008
    Location
    Temecula, CA (Southern CA)
    Posts
    17
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    maybe this could help? (see attached)
    Replacing wheel bearing Attached Files
    Reply With Quote  
     

Similar Threads

  1. going on 4th Wheel Bearing
    By Toofastgs in forum Brakes/Suspension/Chassis
    Replies: 29
    Last Post: 05-16-2014, 04:24 PM
  2. Spun bearing! swap to L26??
    By gixer2000 in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 11
    Last Post: 10-05-2008, 08:35 AM
  3. Wheel bearing questions...
    By Iron Indian in forum Brakes/Suspension/Chassis
    Replies: 6
    Last Post: 09-21-2008, 11:05 AM
  4. Replace cam bearing with engine still in?
    By DanGTP in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 4
    Last Post: 08-28-2008, 09:05 PM
  5. Drive Sprocket Support Bearing
    By JJ91284 in forum 1997-2007 4 speed Automatic (4T65E) (4T65E-HD)
    Replies: 12
    Last Post: 07-02-2008, 05:50 PM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •