Thread: Brembo brakes (ATS)

Results 1 to 11 of 11
  1. #1 Brembo brakes (ATS) 
    SE Level Member
    Join Date
    Apr 2019
    Location
    St. Charles
    Posts
    15
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Well I needed new brakes and since I can't leave anything alone I decided to do a Frankenstein project. I installed calipers for a 2013 ats-v 4 piston brembo bolted right up. Replaced hoses with ats-v hoses. The rotors are where it gets interesting ats-v rotors will not work due to the hat height. They are 321mm diameter. F body rotors are only 315 mm leaving pads hanging over the top. impala/lacrosse rotors are 321mm right height wrong hub bore. Gxp rotors are 323mm and fit however the pads hang over the centers just a bit. Any advice?
    Reply With Quote  
     

  2. #2 Re: Brembo brakes (ATS) 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,919
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    seems to me you need to make caliper brackets that work right.

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  3. #3 Re: Brembo brakes (ATS) 
    SE Level Member
    Join Date
    Apr 2019
    Location
    St. Charles
    Posts
    15
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    No they fit fine just need more rotor surface area. As the GXP rotors taper toward the hat instead of being flat. Just curious if anyone has found a rotor that meets those criteria.
    Reply With Quote  
     

  4. #4 Re: Brembo brakes (ATS) 
    GXP Level Member Turbocharged400sbc's Avatar
    Join Date
    Jan 2008
    Location
    hangover park IL
    Posts
    2,714
    Thanks (Received)
    4
    Likes (Received)
    11
    Dislikes (Received)
    0
    this isnt going onto a W or H body?

    the hub bore of the 12" W rotor should fit your hub....

    sounds like you just need to have the bores opened up on the one rotor
    ~James~ Psychotic Gearhead
    projects: 84 Cressida waGN~ 90 LN3 3800, equal length headers, T70, 89 700r4, misc parts,
    1994 Oldsmobile 442 (462ci-4wd-2 engines) L67/4t80e^2,
    00 Turbo Regal 608 fwhp 575ftlbs at 5500rpm, 98 WhippledRiv, 97 GTP
    Reply With Quote  
     

  5. #5 Re: Brembo brakes (ATS) 
    SE Level Member
    Join Date
    Apr 2019
    Location
    St. Charles
    Posts
    15
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Hub bore is fine. Pad to rotor surface area is to small as on the w rotors they taper inward toward the hat. As far as getting the bore opened up on the ats rotors the hat itself is to tall. Almost 2.5 inches vs the w 2"
    Reply With Quote  
     

  6. #6 Re: Brembo brakes (ATS) 
    SE Level Member
    Join Date
    Sep 2014
    Location
    South Carolina
    Posts
    80
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Hey, did you ever find a solution for this? I noticed that ZZP sells a kit that uses the ATS calipers you're talking about. They mention the have some "custom ZZP caliper shim." Looking at their picture, they have the 6 piston caliper brake pad clip instead of the 4 piston brake pad clip and I'm wondering if that's how they got the pad centered on the rotor better.

    ZZP's kit: ZZP GXP 12.7" Four Piston Brake Kit
    – ZZPerformance

    2013 ATS 6 piston hardware: More Information for ACDELCO 18K2108X
    2013 ATS 4 piston hardware: More Information for ACDELCO 18K8217X
    Gen V M90 | 3.2" Pulley | N* Throttle Body | ZZP SSIC | S1X Blower Cam | INTENSE SIII Heads | 42# Injectors | Pacesetter Headers | Aluminum Subframe | ZZP Lowering Springs | KYB AGX Struts
    Reply With Quote  
     

  7. #7 Re: Brembo brakes (ATS) 
    SE Level Member
    Join Date
    Apr 2019
    Location
    St. Charles
    Posts
    15
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    No I did not, and I have never seen this and the kit they are selling is pretty reasonable. I spent about $450 piecing this together. For the front. I will try and call to get more info on those shims. I can also say that as is now it is a night and day difference.
    Reply With Quote  
     

  8. #8 Re: Brembo brakes (ATS) 
    SE Level Member
    Join Date
    Apr 2019
    Location
    St. Charles
    Posts
    15
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Also it does fit 17" wheels these do clear the caliper height however a 1." wheel spacer is required for x factor clearance. I went with a 1.25" to clear the oem studs 04-08. Side note put the spacers on all 4 wheels not just the front ( requires rolling and stretching rear fenders) otherwise it will handle terrible.
    Reply With Quote  
     

  9. #9 Re: Brembo brakes (ATS) 
    SE Level Member
    Join Date
    Sep 2014
    Location
    South Carolina
    Posts
    80
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Agreed, their kit isn't too bad. I'd buy it but I'm not interested in the pads or rotors they sell in the kit. Let me know if you hear anything on the shims in their kit.

    Good to know on the wheels, I'm running 18" Bonneville GXP wheels so hopefully I won't have issues there.
    Gen V M90 | 3.2" Pulley | N* Throttle Body | ZZP SSIC | S1X Blower Cam | INTENSE SIII Heads | 42# Injectors | Pacesetter Headers | Aluminum Subframe | ZZP Lowering Springs | KYB AGX Struts
    Reply With Quote  
     

  10. #10 Re: Brembo brakes (ATS) 
    SE Level Member
    Join Date
    Apr 2019
    Location
    St. Charles
    Posts
    15
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    So I finally got around to calling zzp they of course would not give me any info. Have to buy the whole kit. Gee thanks. I would say for now the best bet is to trim/mill a little off the bottom of the pad. I am still running them as is no issues yet, however I am certain the pads will eventually wear angled due to them being about 2mm to close to the center.
    Reply With Quote  
     

  11. #11 Re: Brembo brakes (ATS) 
    SE Level Member
    Join Date
    Sep 2014
    Location
    South Carolina
    Posts
    80
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    I figured they probably wouldn't want to share their secrets. Thanks for the update!
    Gen V M90 | 3.2" Pulley | N* Throttle Body | ZZP SSIC | S1X Blower Cam | INTENSE SIII Heads | 42# Injectors | Pacesetter Headers | Aluminum Subframe | ZZP Lowering Springs | KYB AGX Struts
    Reply With Quote  
     

Similar Threads

  1. brembo 13.6 kit
    By Charged4Door in forum Brakes/Suspension/Chassis
    Replies: 7
    Last Post: 09-23-2014, 03:05 PM
  2. CTS-V brembo calipers with pads and pin kit
    By OmegaRed in forum For Sale - Parts
    Replies: 2
    Last Post: 10-12-2013, 10:35 PM
  3. Brembo brakes or f-body brakes? Any other choices?
    By LAST2DOOR in forum Brakes/Suspension/Chassis
    Replies: 4
    Last Post: 09-26-2013, 10:37 PM
  4. Brake Review - Brembo/Hawk HPS
    By tonkota in forum Brakes/Suspension/Chassis
    Replies: 0
    Last Post: 02-12-2009, 11:43 AM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •