Thread: My Latest Mod - Lighted cupholders

Page 1 of 4 123 ... LastLast
Results 1 to 20 of 71
  1. #1 My Latest Mod - Lighted cupholders 
    I say it with pictures Abrasive's Avatar
    Join Date
    Dec 2007
    Location
    Odessa, MO
    Posts
    1,586
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    37
    I guess this falls into Visual Electronics.

    Been working on this for a little while and the reason I was aking how to remove the cupholders. I'm sure some of you will think it's rice, but I don't care. Took my time, did everything they way I wanted it with solder, shrink tube and insulated easy disconnects in case I need to take the center console off again in the future. Put them on a switch also so they can be turned on and off as I please. I used two red LEDs and sanded them down so they are flat on top and then wetsanded them on top with 1000 grit to shine them back up. I did this so that when I insert them in the bottom of the cupholders in the two holes I drilled, they sit flush with the bottom and fill the holes completely, making them nearly vanish when they are off. The cupholders still open and close into the console just like they always did. The two LEDs are wired in series with one 560 ohm resistor.

    Here they are off, you can barely tell they are even there.


    Here they are lit up with the rest of the lights on. Pretty bright, which is why I put them on their own switch so that I don't always have to have them on.


    I don't drink and drive, but this was the only clear bottle I had available in the garage refrigerator at the moment. Pretty cool effect I think.

    Master Certified Auto Glass Technician - 23+ yrs in the biz.
    Reply With Quote  
     

  2. #2 Re: My Latest Mod - Lighted cupholders 
    club of used to own a gp 99prixgt's Avatar
    Join Date
    Jun 2008
    Location
    Jersey
    Posts
    4,643
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    1002
    Nice mod, drinking and driving are we?
    16' wrx sti- stock
    06 Spice Red GTO- m6/exhaust/tune/suspension/377whp-383tq-sold
    99 silvermist gp gt-g5/xp/IC/3.0mps-parted&sold
    Reply With Quote  
     

  3. #3 Re: My Latest Mod - Lighted cupholders 
    I say it with pictures Abrasive's Avatar
    Join Date
    Dec 2007
    Location
    Odessa, MO
    Posts
    1,586
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    37
    Quote Originally Posted by 99prixgt View Post
    Nice mod, drinking and driving are we?
    Quote Originally Posted by Abrasive View Post
    I don't drink and drive, but this was the only clear bottle I had available in the garage refrigerator at the moment.
    HAHA, no, just all I had. But I do drink and mod.

    Master Certified Auto Glass Technician - 23+ yrs in the biz.
    Reply With Quote  
     

  4. #4 Re: My Latest Mod - Lighted cupholders 
    Banned
    Join Date
    Dec 2007
    Location
    Wichita Falls, Texas
    Posts
    5,431
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    Rofl, wicked.
    Reply With Quote  
     

  5. #5 Re: My Latest Mod - Lighted cupholders 
    GTP Level Member Smokin2000gtp's Avatar
    Join Date
    Jul 2008
    Location
    Dekalb, IL
    Posts
    556
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    That's bad ass
    2000 Silvermist Grand Prix GTP Coupe

    Mods-Custom Thrasher CAI|Ceramic Coated S&S Headers|3.4" pulley|ZZP S4 Blower|Powrtuner|PRJ 10.4mm wires|HIDs|F-Body brakes|Koni's and Voglant's|
    Reply With Quote  
     

  6. #6 Re: My Latest Mod - Lighted cupholders 
    GTP Level Member speedemongtp's Avatar
    Join Date
    Jun 2008
    Location
    Ohio
    Posts
    1,431
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    Abrasive thats pretty awesome. Are you gonna do a writeup on that? I think thats a mod i would be willing to attempt. How do you determine on and off? Are they just on a flipswitch or do you have them on some sort of switch that opens an closes the circuit when you open or close the cup holder?
    00 GTP demodded and forsale
    Reply With Quote  
     

  7. #7 Re: My Latest Mod - Lighted cupholders 
    I live here. SyntheticShield's Avatar
    Join Date
    Dec 2007
    Location
    Oklahoma
    Posts
    8,200
    Thanks (Received)
    3
    Likes (Received)
    3
    Dislikes (Received)
    0
    Chats
    0
    Looks like something out of the rainbow coalition gift catalog, LOL
















    Nah, just kidding, that looks extremely nice. I hope you do a write up so I can copy ya.
    Reply With Quote  
     

  8. #8 Re: My Latest Mod - Lighted cupholders 
    The mod from over yonder TheOtherNick's Avatar
    Join Date
    Sep 2008
    Location
    Charles City, IA
    Posts
    9,955
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    3061
    Looks good
    01 gtp-big cam e85 dd 78dodge- guzzling fuel 05 cummins- rollin coal
    SMGPFC Two Nipple General
    Reply With Quote  
     

  9. #9 Re: My Latest Mod - Lighted cupholders 
    I say it with pictures Abrasive's Avatar
    Join Date
    Dec 2007
    Location
    Odessa, MO
    Posts
    1,586
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    37
    Quote Originally Posted by SyntheticShield View Post
    Looks like something out of the rainbow coalition gift catalog, LOL
    Been looking through their catalog have ya? One question, when that comes to your house in the mail, does it come in a brown sleeve or just "out" where everyone knows?

    Master Certified Auto Glass Technician - 23+ yrs in the biz.
    Reply With Quote  
     

  10. #10 Re: My Latest Mod - Lighted cupholders 
    GT Level Member pski920's Avatar
    Join Date
    Oct 2008
    Location
    Endicott NY
    Posts
    248
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    hahaha...rainbow coalition catalog!? never heard that, good one! they look pretty damn good! are they wired into the center console lights so they come on when the dash lights are on?
    Reply With Quote  
     

  11. #11 Re: My Latest Mod - Lighted cupholders 
    GrandPrix Junkie Sabrewings's Avatar
    Join Date
    Dec 2007
    Location
    Barksdale AFB, LA
    Posts
    4,879
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    Do a write up! I've been thinking about doing this after seeing it done a few times, but I haven't seen such a clean install as yours.

    I have so many LEDs and resistors sitting around from my interior conversion I want to put them to use.
    2004 Impala LS - got some mods sold!!!
    2009 Subaru Impreza WRX STI

    NAIOA moderator Still Imp'n, just in a different Imp.
    Reply With Quote  
     

  12. #12 Re: My Latest Mod - Lighted cupholders 
    GXP Level Member boosting98's Avatar
    Join Date
    Mar 2008
    Location
    Wisconsin
    Posts
    2,995
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    2
    reminds me of a scion. i still like it tho!
    Reply With Quote  
     

  13. #13 Re: My Latest Mod - Lighted cupholders 
    GTP Level Member JoshMcMadMac's Avatar
    Join Date
    Jan 2008
    Location
    Waynesboro, PA
    Posts
    823
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    4
    Chats
    0
    Very cool. I love seeing ingenuity!
    2000 NavyBlueMetallic GTP Coupe
    HPTuners / Intercooler / Devil's Own Meth / 1.8 SLP Rockers / 3.1-3.3" / 180° / TB Shield / FWI / PLOG / Jimmy-C Downpipe / U-Bend Delete / Mark VIII Fan / Alt. rewire / FP rewire / F-Body Brakes / Buick Strut Braces / SLP Tips / 20% Tint
    Reply With Quote  
     

  14. #14 Re: My Latest Mod - Lighted cupholders 
    I say it with pictures Abrasive's Avatar
    Join Date
    Dec 2007
    Location
    Odessa, MO
    Posts
    1,586
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    37
    Quote Originally Posted by speedemongtp View Post
    Abrasive thats pretty awesome. Are you gonna do a writeup on that? I think thats a mod i would be willing to attempt. How do you determine on and off? Are they just on a flipswitch or do you have them on some sort of switch that opens an closes the circuit when you open or close the cup holder?

    They are on just a low profile flip switch. Two reasons for this is one, I can turn them off even with the cup holders out in case they come to the point where they are distracting while driving. It's dark here now and I lit them up out in the dark and they are not as bright as they seemed they would be. Just about right in my opinion.

    The second reason is that I already had a switch in the center console. The previous owner had installed it for the performance shift. Well, as a side mod to this LED project, I got a performance shift shifter knob from a friend of mine. So now I had this switch in the console that I wasn't going to be using and I couldn't just remove it because of the hole it would leave behind. The switch he used was lighted, but never was hooked to power, so I swapped it out with one exactly the same only all black and not lit (because I didn't want it lighted) and decided to just use it for these LEDs in the cupholders. Not where I would like to have had it, but unless I replace the top of the console, not much I can do about it.



    The shifter knob I got was pretty beat up and had some cuts in the leather. I ended up carefully cutting the leather on mine and then dremeling out a hole in mine for the perf shift button. I then installed the button from the ragged knob into my stock one. Turned out pretty good I think.

    Last edited by Abrasive; 12-14-2008 at 09:15 PM.

    Master Certified Auto Glass Technician - 23+ yrs in the biz.
    Reply With Quote  
     

  15. #15 Re: My Latest Mod - Lighted cupholders 
    I say it with pictures Abrasive's Avatar
    Join Date
    Dec 2007
    Location
    Odessa, MO
    Posts
    1,586
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    37
    Quote Originally Posted by Sabrewings View Post
    Do a write up! I've been thinking about doing this after seeing it done a few times, but I haven't seen such a clean install as yours.

    I have so many LEDs and resistors sitting around from my interior conversion I want to put them to use.
    I could do a basic write-up I guess. Honestly, I didn't take any pics on the way through because I wasn't sure how good it was going to turn out. LOL! I'll put together something for you guys though, even if it's just a few pointers to follow along with.
    Last edited by Abrasive; 12-14-2008 at 07:52 PM.

    Master Certified Auto Glass Technician - 23+ yrs in the biz.
    Reply With Quote  
     

  16. #16 Re: My Latest Mod - Lighted cupholders 
    GTP Level Member speedemongtp's Avatar
    Join Date
    Jun 2008
    Location
    Ohio
    Posts
    1,431
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    Ic ic sounds like a good use for the switch an a good idea behind making it switchable like that. As far as the shift knob it looks pretty good.
    00 GTP demodded and forsale
    Reply With Quote  
     

  17. #17 Re: My Latest Mod - Lighted cupholders 
    GrandPrix Junkie Sabrewings's Avatar
    Join Date
    Dec 2007
    Location
    Barksdale AFB, LA
    Posts
    4,879
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    Quote Originally Posted by Abrasive View Post
    I could do a basic write-up I guess. Honestly, I didn't take any pics on the way through because I wasn't sure how good it was going to turn out. LOL! I'll put together something for you guys though, even if it's just a few pointers to follow along with.
    The only part I'm slightly fuzzy on is how to attach the LEDs to the plastic and keep them there over time. I can handle the rest.
    2004 Impala LS - got some mods sold!!!
    2009 Subaru Impreza WRX STI

    NAIOA moderator Still Imp'n, just in a different Imp.
    Reply With Quote  
     

  18. #18 Re: My Latest Mod - Lighted cupholders 
    I say it with pictures Abrasive's Avatar
    Join Date
    Dec 2007
    Location
    Odessa, MO
    Posts
    1,586
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    37
    Quote Originally Posted by Sabrewings View Post
    The only part I'm slightly fuzzy on is how to attach the LEDs to the plastic and keep them there over time. I can handle the rest.

    I used 5mm leds and drilled the holes in the cupholders using a 13/64 drillbit and I kinda wiggled it around in the holes a bit. They fit very tightly and I doubt they would have fallen out, but I did put a drop of gorrilla glue on the underside just in case. Probably would have been better to use a drop of silicone or rtv so you could take it back out easier later if need be. I bought various led holders, but none of the ones I got really would have worked without putting them through from the top side. I wanted them flush so anything with a flat bottom wouldn't wobble in the cupholder.

    Master Certified Auto Glass Technician - 23+ yrs in the biz.
    Reply With Quote  
     

  19. #19 Re: My Latest Mod - Lighted cupholders 
    I say it with pictures Abrasive's Avatar
    Join Date
    Dec 2007
    Location
    Odessa, MO
    Posts
    1,586
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    37
    Well, here is the very basics to this mod.

    First I started out at Radio Shack and picked up a small variety pack of 5mm LEDs and a pack of 560ohm resistors. I got the variety pack because it was actually cheaper than buying the LEDs seperately and it had 4 red ones in it so in case I messed one up I would have a couple extras.

    These first few sanding steps can be skipped if you want to order your LEDs from superbrightleds.com since they actually sell 5mm LEDs that are already flat on top. This would save you some work if you want to wait on them to be shipped to you. I had the means to make them myself, so I did it this way.

    First thing I did was to take my dremel tool and stack a bunch of sanding disks on top of eachother. This was to make it more solid so I would end up with a more true flat surface on the LED.


    Next I sanded down the rounded end of the LED so that it was flat.


    Here's after the dremel sanding. I used a green one just for these pics since I probably won't ever use it anyway and I already had the ones in my cupholders done.


    Next I laid a piece of 1000 grit sandpaper on a block of wood (again, just to keep things flat) and wetsanded the end of the led to take the roughness off from the dremel sanding.


    Here's the LED after the wetsanding. Not totally clear but much smoother than just after the dremel, and this probably diffuses the light a little better anyway.


    Next you need to wire up your LEDs and resistor. You will need a short piece of wire to connect in between the LEDs. When I soldered mine together, I covered all of the wires and resistor with shrink tube so there were no bare wires when I was finished. Here is a very helpful website for calculating what resistors to use if you decide to use different/more/less LEDs - http://ledcalc.com/


    Now you will have to remove the top of your center console. I measured out and drilled one hole in each cupholder with a 13/64 drill bit. I then inserted the LED circuit I made in from the bottom of the cupholders. The LEDs fit very tightly and could probably be left as is, but I did use a drop of glue on the bottom side of each one to make sure they never fell out. You can also see in this picture where I marked true center of the cupholder if it were a complete circle. I ended up changing this since most bottles will not fill the entire cupholder. There was a slight ring on the bottom of the cupholder left behind from cans and such, so I centered the LED in that circle so it would end up more centered under a bottle. After thinking about this a while, I am glad I did this. I think they would have looked odd over closer to that flat edge of the bottom.


    Now all that's left is to wire your LED circuit to power and ground. I will leave these decisions up to you. I used a switch to turn mine on and off and got power from the auxillary power outlet on the front passenger side of the console. This is a constant 12v source. You could also easily tap power from the light bulb in the shifter display if you would like them to just come on and dim with the rest of the car's lights. You could get fancy with a mercury switch on the cupholder itself also if you wanted them to just some on when you open the cupholders. As for the ground, the easiest place was directly below the cupholder to one of the two 10mm bolts that hold the center console in place, which is where I grounded mine.

    I highly suggest using some sort of disconnects so that you can easily unhook the wires in the event you need to remove the top of the center console. It also makes wiring easier since you can get it all ready then just plug it right in when you put the top of the console back on. I used these on both my power and ground wires.


    Here's the finished product.


    My switch location. I already had a switch there from an old performance shift install which I changed once I got a perf shift knob, so I just made use of what was already here.

    Master Certified Auto Glass Technician - 23+ yrs in the biz.
    Reply With Quote  
     

  20. #20 Re: My Latest Mod - Lighted cupholders 
    GrandPrix Junkie Sabrewings's Avatar
    Join Date
    Dec 2007
    Location
    Barksdale AFB, LA
    Posts
    4,879
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    Good info, thanks. If I ever get a rainy day I may do this.
    2004 Impala LS - got some mods sold!!!
    2009 Subaru Impreza WRX STI

    NAIOA moderator Still Imp'n, just in a different Imp.
    Reply With Quote  
     

Page 1 of 4 123 ... LastLast

Similar Threads

  1. Latest S2 3800 Swap FINISHED!!!!
    By Trannyman95 in forum Off Topic Discussion
    Replies: 5
    Last Post: 07-24-2008, 02:16 AM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •