Thread: *HOW TO* Ford Fusion Fog's for GXP

Page 1 of 2 12 LastLast
Results 1 to 20 of 25
  1. #1 *HOW TO* Ford Fusion Fog's for GXP 
    I live here. DirtDog's Avatar
    Join Date
    Jun 2012
    Location
    Jacksonville, North Carolina, United States
    Posts
    7,750
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Ok so this write up is for Pontiac Grand Prix GXP’s stock fog light to Fusion Fog light conversion. Its not a hard process and only cost me about 94 bucks and a lot of time cause I had to figure out how I wanted to do it. And there is tons of pics to make it easier for anyone else who wants to do it.

    And thanks to Koniig for advice on how he did his. Helped out a lot.

    So first things first. This link is the link to where I purchased the fusion fogs from
    http://www.hidplanet.com/forums/show...-for-HID/page8
    and here they are in person side by side


    Ok and now for the retro fitting to make them work which is a very simple but time consuming process. Another guy did it and he used bolts but I just couldn’t see how so I took a different route to make them work...you will see further down

    Picture below is a side by side comparison of the new fusion fogs (on the left) and the old stock fogs (on the right)




    And these are just pics of the new fusions



    Here in this one I took the outside housings off of one of the old and one of the new just to compare. Its really unnecessary to do


    Here is just the old fog in the stock adjustable bracket that is in the bumper. That bracket that the fogs are screwed to just pops off…but I must admit it is a real pain in the as* and a few choice words did help



    This is the new fusion fogs in the stock adjuster bracket from the bumper. I was just mocking them up to see how theyd fit



    And actually seemed like a way better fit

    This is the new bracket from fusion fogs sitting in the old bumper bracket. The fog is taken out of the bracket here cause I wanted to look at it




    Pics of the front of the bumper where I took them out. I pulled the honeycomb stuff out cause there was no other way to do this without removing bumper. And the honeycomb stuff pulls out…it’s a pain but it does just come out



    Now for the fun crap. I used a very large hose clamp to hold the new fusions inside the bumper bracket. The trick is to make sure that the clamp doesn’t touch the lenses on the front…I put a piece of carboard inbetween them.



    Also to center the fusions I used a budwiser box and a ruler to get it even on all the sides…and drinking a couple beers also helps out a lot


    And to secure the new fusions in the bracket I used jb weld…
    Heres the jb weld I used see the bottom to a trick I learned to set it quicker on the fogs
    http://shop.advanceautoparts.com/web...weld_7160039-p





    And the first one is done

    Last edited by DirtDog; 04-22-2013 at 07:25 AM.
    http://www.grandprixforums.net/my-06-gp-gxp-72403.html
    OBX headers, TEP tranny cooler, ls1 IM fuel rails and injectors, ls2 TB, ls7 MAF, full custom exhaust, Quad retro headlights, full out front and rear suspension work, tuned by HPT by me 8====>

    Reply With Quote  
     

  2. #2 Re: this is a how to for gxp fusion fog modification. 
    I live here. DirtDog's Avatar
    Join Date
    Jun 2012
    Location
    Jacksonville, North Carolina, United States
    Posts
    7,750
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    I did put more jb weld on this one…I just didn’t feel like mixing up more at the time when I did this one


    First one installed


    When I got the other one done and installed It was dark so I just turned them on. I haven’t aimed them yet so they shine kinda high but even so their way better than the stock ones




    Once I get them aimed where I want them ill take some pics of the light out put for yall

    Trick for using the jb weld since its kinda runny for awhile after mixing. I would mix the jb up on a piece of card board and let it sit for about two hours to where it starts to get really sticky and tacky. Then take a heat gun and heat the jb weld up and itll get runny. Put a little on at a time with what ever application thingy you use and stick it in a freezer and it cools it back down to where its sticky and not runny again and just apply it like that.

    This is how the fogs looked before…nice and yellowish. Now all I need is some switchbacks for my turn signal so its all white light…o and start my headlight retros


    And just to show off my beauty here ya go



    If there’s anything I forgot or any questions please feel free to post and ill answer em or make changes to the how to.

    Side not I’m going to stick some hid’s in them sometime in the near future since they won’t melt the housings on these just to see

    Updated:::
    Here's some output pics. I need to aim the passenger side a few more degrees cause its still high. I also need to drive around and see how I like where I have them now


    Last edited by DirtDog; 04-22-2013 at 09:18 PM.
    http://www.grandprixforums.net/my-06-gp-gxp-72403.html
    OBX headers, TEP tranny cooler, ls1 IM fuel rails and injectors, ls2 TB, ls7 MAF, full custom exhaust, Quad retro headlights, full out front and rear suspension work, tuned by HPT by me 8====>

    Reply With Quote  
     

  3. #3 Re: this is a how to for gxp fusion fog modification. 
    Brightening up your day. Koniig's Avatar
    Join Date
    Jun 2010
    Location
    Illinois.
    Posts
    1,345
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Looks good, boss.

    And I have to gloat a little: I do love breaking new ground in the Grand Prix world.

    Reply With Quote  
     

  4. #4 Re: this is a how to for gxp fusion fog modification. 
    I live here. DirtDog's Avatar
    Join Date
    Jun 2012
    Location
    Jacksonville, North Carolina, United States
    Posts
    7,750
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Quote Originally Posted by Koniig View Post
    Looks good, boss.

    And I have to gloat a little: I do love breaking new ground in the Grand Prix world.

    You deserved it...and then I stole ur idea and helped perfect it :P sorta
    http://www.grandprixforums.net/my-06-gp-gxp-72403.html
    OBX headers, TEP tranny cooler, ls1 IM fuel rails and injectors, ls2 TB, ls7 MAF, full custom exhaust, Quad retro headlights, full out front and rear suspension work, tuned by HPT by me 8====>

    Reply With Quote  
     

  5. #5 Re: this is a how to for gxp fusion fog modification. 
    Brightening up your day. Koniig's Avatar
    Join Date
    Jun 2010
    Location
    Illinois.
    Posts
    1,345
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Quote Originally Posted by marines542 View Post
    You deserved it...and then I stole ur idea and helped perfect it :P sorta
    Haha not stolen! But improved upon without a doubt!
    Reply With Quote  
     

  6. #6 Re: this is a how to for gxp fusion fog modification. 
    GTX Level Member
    Join Date
    Dec 2012
    Location
    wichita,ks
    Posts
    812
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Are you on a phone or computer op?
    It is just a FAMILY CAR
    Reply With Quote  
     

  7. #7 Re: this is a how to for gxp fusion fog modification. 
    I live here. DirtDog's Avatar
    Join Date
    Jun 2012
    Location
    Jacksonville, North Carolina, United States
    Posts
    7,750
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Phone why? I can get on a computer though
    http://www.grandprixforums.net/my-06-gp-gxp-72403.html
    OBX headers, TEP tranny cooler, ls1 IM fuel rails and injectors, ls2 TB, ls7 MAF, full custom exhaust, Quad retro headlights, full out front and rear suspension work, tuned by HPT by me 8====>

    Reply With Quote  
     

  8. #8 Re: this is a how to for gxp fusion fog modification. 
    I live here. DirtDog's Avatar
    Join Date
    Jun 2012
    Location
    Jacksonville, North Carolina, United States
    Posts
    7,750
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Bump updated with some out put pics more to come when I ain some more. It started raining so I had to call it a night
    http://www.grandprixforums.net/my-06-gp-gxp-72403.html
    OBX headers, TEP tranny cooler, ls1 IM fuel rails and injectors, ls2 TB, ls7 MAF, full custom exhaust, Quad retro headlights, full out front and rear suspension work, tuned by HPT by me 8====>

    Reply With Quote  
     

  9. #9 Re: this is a how to for gxp fusion fog modification. 
    I live here. DirtDog's Avatar
    Join Date
    Jun 2012
    Location
    Jacksonville, North Carolina, United States
    Posts
    7,750
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Quick update.* I've been driving with em angled the way I have em and have come to the conclusion I need to change the aim higher.* I got them angled too low.* Still though there's a huge improvement
    http://www.grandprixforums.net/my-06-gp-gxp-72403.html
    OBX headers, TEP tranny cooler, ls1 IM fuel rails and injectors, ls2 TB, ls7 MAF, full custom exhaust, Quad retro headlights, full out front and rear suspension work, tuned by HPT by me 8====>

    Reply With Quote  
     

  10. #10 Re: this is a how to for gxp fusion fog modification. 
    GTX Level Member
    Join Date
    Dec 2012
    Location
    wichita,ks
    Posts
    812
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    That's a big list to type on a phone lol I hate doing have my post on a dame phone haha
    It is just a FAMILY CAR
    Reply With Quote  
     

  11. #11 Re: this is a how to for gxp fusion fog modification. 
    I live here. DirtDog's Avatar
    Join Date
    Jun 2012
    Location
    Jacksonville, North Carolina, United States
    Posts
    7,750
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Quote Originally Posted by mudneck4 View Post
    That's a big list to type on a phone lol I hate doing have my post on a dame phone haha
    What this u be referring to? I made this how to on my computer
    http://www.grandprixforums.net/my-06-gp-gxp-72403.html
    OBX headers, TEP tranny cooler, ls1 IM fuel rails and injectors, ls2 TB, ls7 MAF, full custom exhaust, Quad retro headlights, full out front and rear suspension work, tuned by HPT by me 8====>

    Reply With Quote  
     

  12. #12 Re: this is a how to for gxp fusion fog modification. 
    GTX Level Member
    Join Date
    Dec 2012
    Location
    wichita,ks
    Posts
    812
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    That's what I was asking lol nice how to btw
    It is just a FAMILY CAR
    Reply With Quote  
     

  13. #13 Re: this is a how to for gxp fusion fog modification. 
    I live here. DirtDog's Avatar
    Join Date
    Jun 2012
    Location
    Jacksonville, North Carolina, United States
    Posts
    7,750
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    O OK cool. And thanks its definitely a very nice upgrade
    http://www.grandprixforums.net/my-06-gp-gxp-72403.html
    OBX headers, TEP tranny cooler, ls1 IM fuel rails and injectors, ls2 TB, ls7 MAF, full custom exhaust, Quad retro headlights, full out front and rear suspension work, tuned by HPT by me 8====>

    Reply With Quote  
     

  14. #14 Re: this is a how to for gxp fusion fog modification. 
    Banned
    Join Date
    Jan 2013
    Location
    the bandwagon follower aka noobiee
    Posts
    770
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    look tits love the color I hate my color on my car
    Reply With Quote  
     

  15. #15 Re: this is a how to for gxp fusion fog modification. 
    I live here. DirtDog's Avatar
    Join Date
    Jun 2012
    Location
    Jacksonville, North Carolina, United States
    Posts
    7,750
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Finally got them where I like. Only one problem. I'll point that out once I get on my computer and edit the pic with arrows to show ya






    http://www.grandprixforums.net/my-06-gp-gxp-72403.html
    OBX headers, TEP tranny cooler, ls1 IM fuel rails and injectors, ls2 TB, ls7 MAF, full custom exhaust, Quad retro headlights, full out front and rear suspension work, tuned by HPT by me 8====>

    Reply With Quote  
     

  16. #16 Re: this is a how to for gxp fusion fog modification. 
    Banned
    Join Date
    Jan 2013
    Location
    the bandwagon follower aka noobiee
    Posts
    770
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    looks nice
    Reply With Quote  
     

  17. #17 Re: this is a how to for gxp fusion fog modification. 
    I live here. DirtDog's Avatar
    Join Date
    Jun 2012
    Location
    Jacksonville, North Carolina, United States
    Posts
    7,750
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Quote Originally Posted by importisland13 View Post
    looks nice
    Yup I love em.
    http://www.grandprixforums.net/my-06-gp-gxp-72403.html
    OBX headers, TEP tranny cooler, ls1 IM fuel rails and injectors, ls2 TB, ls7 MAF, full custom exhaust, Quad retro headlights, full out front and rear suspension work, tuned by HPT by me 8====>

    Reply With Quote  
     

  18. #18 Re: this is a how to for gxp fusion fog modification. 
    Brightening up your day. Koniig's Avatar
    Join Date
    Jun 2010
    Location
    Illinois.
    Posts
    1,345
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    If you're talking about the foreground limiter on them being the problem (where the light emitted begins to illuminate the road in front of your car), they can be removed.
    Reply With Quote  
     

  19. #19 Re: this is a how to for gxp fusion fog modification. 
    I live here. DirtDog's Avatar
    Join Date
    Jun 2012
    Location
    Jacksonville, North Carolina, United States
    Posts
    7,750
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Not really although id like that removed. The problem being it shines into the honeycomb grill a little. I can fix that easily though
    http://www.grandprixforums.net/my-06-gp-gxp-72403.html
    OBX headers, TEP tranny cooler, ls1 IM fuel rails and injectors, ls2 TB, ls7 MAF, full custom exhaust, Quad retro headlights, full out front and rear suspension work, tuned by HPT by me 8====>

    Reply With Quote  
     

  20. #20 Re: this is a how to for gxp fusion fog modification. 
    SE Level Member
    Join Date
    Apr 2013
    Location
    Macomb Mi
    Posts
    23
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Looks great! Ps love the choice of cardboard! Lol
    Reply With Quote  
     

Page 1 of 2 12 LastLast

Similar Threads

  1. Ford fusion 17's on Grand Prix?
    By ebk231 in forum General Grand Prix Discussion
    Replies: 13
    Last Post: 08-17-2015, 08:06 AM
  2. 09 ford fusion water in floorboard
    By luckyg817 in forum Other Vehicles
    Replies: 13
    Last Post: 07-03-2014, 01:28 PM
  3. 2013 Ford Fusion: What do you think of it?
    By Hippo Machine in forum Off Topic Discussion
    Replies: 21
    Last Post: 01-15-2012, 03:10 PM
  4. 263 hp ford fusion
    By BlackGT97 in forum General Tech Discussion
    Replies: 3
    Last Post: 11-19-2011, 10:35 PM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •