Thread: Won't start after cam install

Page 1 of 23 12311 ... LastLast
Results 1 to 20 of 448
  1. #1 Won't start after cam install 
    GTP Level Member Bedwards's Avatar
    Join Date
    Oct 2009
    Location
    Calgary, Alberta, Canada
    Posts
    863
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    I just got my motor put back in, got everything connected and hooked up, primed the oil pump, but when I go to start it, it just cranks, stutters and "coughs" when you stop cranking off. The cough noise sounds like it comes from the intake, but I'm not sure. Here's a video of it:

    http://i82.photobucket.com/albums/j2...3/01c4a061.mp4

    And

    http://i82.photobucket.com/albums/j2...3/8b0ccd9d.mp4

    I also need help locating where this line plugs into:





    Thanks guys!
    Reply With Quote  
     

  2. #2 Re: Won't start after cam install 
    GrandPrix Junkie PurpleGuy's Avatar
    Join Date
    Aug 2010
    Location
    Never Never Land
    Posts
    4,864
    Thanks (Received)
    1
    Likes (Received)
    10
    Dislikes (Received)
    1
    not sure if im right but i can see on the supercharger vaccum tree your missing a line. it might go there. not sure though.
    2001 Regal GS, PLOG, 3" DP, 1.9's/L76 springs. 21* of timing on a 3.4"
    Reply With Quote  
     

  3. #3 Re: Won't start after cam install 
    The Blue One blueguy's Avatar
    Join Date
    Jun 2008
    Location
    Dirtyzville, Missery
    Posts
    31,287
    Thanks (Received)
    1
    Likes (Received)
    2
    Dislikes (Received)
    0
    It does.

    Plug that line into the top of the blower and see how it runs after that...you've got a decent vac leak right there.
    Sold WBody's: '03 Blue GTP/'98 Green GTP/'98 Silver GT/'05 GXP
    '99 Chevrolet Silverado Classic Z71 4x4 - K&N Intake/Gibson Exhaust #TRUCKTHINGS
    '12 Buick Regal Turbo - ZZP CAI/20% Tint/HID's
    '89 Ford Mustang LX Notchback - LM7 5.3, 4L80, 9", HX40
    '04 Chevrolet Corvette MRM A4/LS1 - TSP LT's, 3"O/R X, AFE S2 CAI
    Reply With Quote  
     

  4. #4 Re: Won't start after cam install 
    GT Level Member Deviq's Avatar
    Join Date
    Aug 2010
    Location
    SE WI
    Posts
    173
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    You can see the empty port on the tree it goes into in the second pic.
    Quote Originally Posted by zildjian102
    .. friggin trashy people. I did stuff with their daughter
    Reply With Quote  
     

  5. #5 Re: Won't start after cam install 
    GTX Level Member GOTIT4CHEAP16's Avatar
    Join Date
    Jan 2010
    Location
    Bowie, MD
    Posts
    613
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    yea thats where mines goes. The middle line in the red circle.

    Gen V, 3.0, Stage 2 heads, XP Cam, SD Headers, N*, LQ4, ZZP Stage 2 Gen 3 Intercooler, CAI, AL 104's Gapped to .055, #130 Springs, 42.5lb Injectors, ZZP Tune.

    Reply With Quote  
     

  6. #6 Re: Won't start after cam install 
    GT Level Member Tea Time's Avatar
    Join Date
    Mar 2011
    Location
    New Brunswick
    Posts
    152
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    All of the above are right about the vacuum line, it runs ur HVAC , plug it into that tree on top the blower and hopefully blue is right about the non start, thats a nasty vacuum leak with it left unplugged.

    '00 GTP - Summer Toy
    '97 GTP - Project
    '99 GT - Gone (Frame Rotted)
    '98 SE - Gone (Parts Car)
    Reply With Quote  
     

  7. #7 Re: Won't start after cam install 
    GTP Level Member Bedwards's Avatar
    Join Date
    Oct 2009
    Location
    Calgary, Alberta, Canada
    Posts
    863
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Thanks guys. I'll plug it in and give it a try tonight. I really hope that's the problem.
    Reply With Quote  
     

  8. #8 Re: Won't start after cam install 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,997
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    it sounds like its back firing out the intake, have you double checked the plug wires firing order? 2 wires in the wrong place will mess you up good.

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  9. #9 Re: Won't start after cam install 
    GTP Level Member Bedwards's Avatar
    Join Date
    Oct 2009
    Location
    Calgary, Alberta, Canada
    Posts
    863
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Quote Originally Posted by scottydoggs View Post
    it sounds like its back firing out the intake, have you double checked the plug wires firing order? 2 wires in the wrong place will mess you up good.
    I'll double check the spark plug wires tonight. I hope it's something simple. This is stressing me out.
    Reply With Quote  
     

  10. #10 Re: Won't start after cam install 
    The mod from over yonder TheOtherNick's Avatar
    Join Date
    Sep 2008
    Location
    Charles City, IA
    Posts
    9,955
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Hook that back up, check plug wires, check icm ground under coil packs.
    01 gtp-big cam e85 dd 78dodge- guzzling fuel 05 cummins- rollin coal
    SMGPFC Two Nipple General
    Reply With Quote  
     

  11. #11 Re: Won't start after cam install 
    Awaiting Confirmation
    Join Date
    Jul 2009
    Location
    aowdnawi
    Posts
    23,292
    Thanks (Received)
    0
    Likes (Received)
    1
    Dislikes (Received)
    0
    Car should still run with that disconnected.

    if the brake booster line was disconnected it wont.
    Reply With Quote  
     

  12. #12 Re: Won't start after cam install 
    GrandPrix Junkie PurpleGuy's Avatar
    Join Date
    Aug 2010
    Location
    Never Never Land
    Posts
    4,864
    Thanks (Received)
    1
    Likes (Received)
    10
    Dislikes (Received)
    1
    really cuz my camaro started with the brake booster line disconnected.
    2001 Regal GS, PLOG, 3" DP, 1.9's/L76 springs. 21* of timing on a 3.4"
    Reply With Quote  
     

  13. #13 Re: Won't start after cam install 
    GTP Level Member Bedwards's Avatar
    Join Date
    Oct 2009
    Location
    Calgary, Alberta, Canada
    Posts
    863
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    So if it won't start with that line connected, and the spark plug wires are all hooked up properly, what should I look at?
    Reply With Quote  
     

  14. #14 Re: Won't start after cam install 
    Moderator dsmuts's Avatar
    Join Date
    Feb 2011
    Location
    Coldwater, OH
    Posts
    15,758
    Thanks (Received)
    1
    Likes (Received)
    1
    Dislikes (Received)
    0
    spray a little starting fluid in it and see if it's a fuel issue.
    98 GTP modded 1.9's, sd headers, 3.4", zzp 1.0 230K miles scrapped.
    04 Comp G zzp stb's, UMI ta's, Speedbuilt sways, bully flo heads, XP, zzp headers, fsic, thrasher shift kit, 60#, 2.6" corsa 2.5", Inferno hood
    01 gt z7 turbo tep trans zzp motor
    08 g8 gt cam exhaust 11.87@118
    Reply With Quote  
     

  15. #15 Re: Won't start after cam install 
    Turbo is the way to go. Fivefingerdeathpunch's Avatar
    Join Date
    Sep 2009
    Location
    Rogers, MN
    Posts
    21,030
    Thanks (Received)
    21
    Likes (Received)
    45
    Dislikes (Received)
    0
    how about take it one step at a time, do what we have suggested then trouble shoot from there.

    SMGPFC Member #1
    Reply With Quote  
     

  16. #16 Re: Won't start after cam install 
    GTP Level Member Bedwards's Avatar
    Join Date
    Oct 2009
    Location
    Calgary, Alberta, Canada
    Posts
    863
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Heading home now. I'll plug in the vacuum line, check the plug wires and re-connect the ground for the ICM. I'll keep you guys posted. Thanks so much for the help so far.
    Reply With Quote  
     

  17. #17 Re: Won't start after cam install 
    GTP Level Member Bedwards's Avatar
    Join Date
    Oct 2009
    Location
    Calgary, Alberta, Canada
    Posts
    863
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Okay I did all those steps. Still won't start. I am still getting that "coughing" noise out of the intake (I think). I have a fuel pressure of about 40 to 45 psi with the key in the "on" position. I also tried holding my foot on the gas, it didn't do anything.
    Reply With Quote  
     

  18. #18 Re: Won't start after cam install 
    Banned
    Join Date
    Mar 2011
    Location
    CT
    Posts
    1,730
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Are you sure your wires aren't backward? The #1 cylinder is in the front left, closest to the coil packs.
    Reply With Quote  
     

  19. #19 Re: Won't start after cam install 
    Turbo is the way to go. Fivefingerdeathpunch's Avatar
    Join Date
    Sep 2009
    Location
    Rogers, MN
    Posts
    21,030
    Thanks (Received)
    21
    Likes (Received)
    45
    Dislikes (Received)
    0
    everything is plugged in?

    maf, map, etc etc

    SMGPFC Member #1
    Reply With Quote  
     

  20. #20 Re: Won't start after cam install 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,997
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    have you checked for spark yet? double checked all the grounds are bolted up? starter wires hooked up right?

    in the vid the battery sounds a little weak.

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

Page 1 of 23 12311 ... LastLast

Similar Threads

  1. how hard is it to install an alarm with remote start
    By nascartech in forum Audio, Security & Visual Electronics
    Replies: 3
    Last Post: 11-01-2010, 05:55 PM
  2. gen v install help
    By aligater in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 5
    Last Post: 02-08-2009, 02:45 PM
  3. Need Help On Troubleshooting Bulldog Security Remote Start Install
    By eb97951 in forum General Tech Discussion
    Replies: 0
    Last Post: 12-24-2008, 07:39 AM
  4. Remote Start Install Questions...
    By Incomudrox in forum Audio, Security & Visual Electronics
    Replies: 1
    Last Post: 12-02-2008, 02:19 PM
  5. car rattles after cam install then wont start at all!
    By chrisb in forum General Tech Discussion
    Replies: 28
    Last Post: 07-11-2008, 10:54 AM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •