Thread: EGR delete w/o PCM Flash

Results 1 to 8 of 8
  1. #1 EGR delete w/o PCM Flash 
    SE Level Member
    Join Date
    Apr 2012
    Location
    MN
    Posts
    13
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    1
    Alright.. I've done a 3400 top end swap in my 98 GP with a 3100 block.. EGR's are different and my Chilton wiring diagram only lists the colors of the wires that are leading to the EGR connector.

    .................................................. ... - ...................... +
    They're labeled on the EGR as follows: ..A.... B...... C.. D... E
    Wire colors are:................................ R.. BR/W.. BR. GY. GY

    I cut the 'E' Gray wire and no longer have MIL codes for EGR low voltage but still have EGR codes for non-op. The manifold port is blocked and EGR tube cut. Having the 'E' wire cut disables the coil inside the EGR.

    I am asking for any input to find a way to fake the computer into thinking the EGR is still operating with out having to flash the PCM. Any ideas?
    Last edited by GP98GTX; 04-28-2012 at 11:55 PM. Reason: Formating
    Reply With Quote  
     

  2. #2 Re: EGR delete w/o PCM Flash 
    GTP Level Member KeithGTP03's Avatar
    Join Date
    Jan 2011
    Location
    Houston
    Posts
    2,841
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    376
    If you find that out, let me know. My codes are tuned out, but I cannot pass inspection because it never completes its test and shows "not ready". Matt had told me that if I connect a wideband output to the EGR position wire, it would trick the comp into thinking its functional. I haven't had a chance to try that.

    EDIT: Just realized I skipped your entire first paragraph. Not sure if this will work on a 3100

    03 GTP...Its got pulleys and stuff.
    Reply With Quote  
     

  3. #3 Re: EGR delete w/o PCM Flash 
    SE Level Member
    Join Date
    Apr 2012
    Location
    MN
    Posts
    13
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    1
    Well I took a simple On/Off 2-pole switch and wired it in series on the 'E' Gray wire. Might not be the right way, but it's working 'right' now..

    Before starting the car I flip the switch 'ON' to close the loop and let the computer run the start test, once driving >30MPH I flip it 'OFF' and haven't had a code pop up yet (Only when I forget to initially turn it 'ON')..

    *I will continue to play around with the wiring and check the local GM dealerships/service shops to see if their repair manuals have better wiring diagrams.*
    Last edited by GP98GTX; 04-30-2012 at 09:30 PM. Reason: Formatting
    Reply With Quote  
     

  4. #4 Re: EGR delete w/o PCM Flash 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,833
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    Chats
    98246
    If you delete the codes in the computer then you typically should be set. Another item to do is set the EGR minimum test temperature to the max setting. In HPT it's 284F. That keeps the test from ever needing to be run.

    I have verified this works.
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  5. #5 Re: EGR delete w/o PCM Flash 
    SE Level Member
    Join Date
    Apr 2012
    Location
    MN
    Posts
    13
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    1
    Quote Originally Posted by BillBoost37 View Post
    If you delete the codes in the computer then you typically should be set. Another item to do is set the EGR minimum test temperature to the max setting. In HPT it's 284F. That keeps the test from ever needing to be run.

    I have verified this works.
    Thanks for the suggestion, but this thread is titled "EGR Delete W/O PCM Flash"

    >>Also the OBD computer does a run-up test under initial engine start and without a complete circuit it will pop a code and illuminate the MIL<<
    Last edited by GP98GTX; 05-01-2012 at 07:09 PM. Reason: Formatting
    Reply With Quote  
     

  6. #6  
    GrandPrix Junkie CrazyGuy03's Avatar
    Join Date
    Jan 2010
    Location
    Buffalo
    Posts
    3,868
    Thanks (Received)
    0
    Likes (Received)
    2
    Dislikes (Received)
    0
    Chats
    7841
    Well if u want to delete it so it's not putting exhaust back into the intake use a block off plate. Block off the exhaust side. That way when it opens it draws in fresh air. The Egr will still function like it should and throw no codes
    2003 Buick Regal GSX lots of mods - click here to see latest build - http://www.grandprixforums.net/threa...ld-for-the-gsx

    *For Reference - Does not have a Zack Howard Cam - It's an Intense Stage 3 - Thank You*
    Reply With Quote  
     

  7. #7 Re: EGR delete w/o PCM Flash 
    SE Level Member
    Join Date
    Apr 2012
    Location
    MN
    Posts
    13
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    1
    Quote Originally Posted by crazyguy03 View Post
    Well if u want to delete it so it's not putting exhaust back into the intake use a block off plate. Block off the exhaust side. That way when it opens it draws in fresh air. The Egr will still function like it should and throw no codes
    The 'up-tube' from the manifold, on this motor, is part of the EGR assembly's mounting (The intake manifold isn't threaded, it only has through holes).
    I had originally thought to put a filter similar to the push-on style VC breathers but decided against it, in-case of some nosey SMOG tester. (I travel to CA regularly)

    Leaving everything 'looking stock' was the goal and hiding a switch and two 22AWG wires was much easier.
    Reply With Quote  
     

  8. #8 Re: EGR delete w/o PCM Flash 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,833
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    Chats
    98246
    Sorry..I was trying to answer part of the question Keith posed to your thread.

    As for being able to do it with a switch. I don't see how. The pcm will command the EGR to run various tests. If it doesn't get responses to pintle position etc etc it will throw codes. Also the PCM looks for a change in map readings when it commands the valve open.
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

Similar Threads

  1. official switchback/led bulb hyperflash fix and sidemarker flash delete.
    By BoostJunki3 in forum Visual/Body Modifications
    Replies: 38
    Last Post: 04-08-2018, 02:54 PM
  2. Disabling Headlight Flash for HID's
    By skidoojames151 in forum How To Write-Ups/Tech Tips
    Replies: 29
    Last Post: 06-14-2012, 12:28 PM
  3. hyperflash fix and sidemarker flash delete.
    By BoostJunki3 in forum How To Write-Ups/Tech Tips
    Replies: 9
    Last Post: 08-16-2011, 04:48 PM
  4. flash floods
    By oneil.GTP in forum Off Topic Discussion
    Replies: 11
    Last Post: 05-18-2010, 12:22 AM
  5. Top Swap Re Flash problem
    By MNGP07 in forum PCM Tuning
    Replies: 2
    Last Post: 03-22-2009, 08:02 PM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •