WBS gen 3 intercooler

**sseilmnop** · 02-04-2014

$400 including shipping.
PayPal as friend or add fees 3%
New never used includes bolts and gaskets.

Shown with a gen 5 gasket.
Can be used with either gen 3 or 5.
It really is best to open up intake for best flow, this is more important then gen 3/5

**kurupt305** · 02-05-2014

this will bolt right up to a gen 5? also can you use stock lower intake manifold?

**sseilmnop** · 02-05-2014

You can use stock lower intake and bolt pattern is the same for gen 3 or 5.

**kurupt305** · 02-06-2014

how much better wold your phenolic ic be

**sseilmnop** · 02-06-2014

Phenolic performs better than the aluminum.

**sseilmnop** · 02-11-2014

Bump

**Kilroy** · 02-11-2014

So, is all else I would need for my 2003 GTP, are the lines, pump, and rad? Is it as simple as removing upper intake, and installing this IC?

**sseilmnop** · 02-11-2014

No not that simple. Need modified fuel rails to go over or around raised up supercharger. Probable have to remove hood blanket/insulation for clearance. Need longer belt.

Have your LIM gaskets been replaced with the aluminum ones yet? You should if you haven't done that yet.

**Kilroy** · 02-12-2014

So, if I got this straight, for my 2003 GTP, I would need modified fuel rails, new gaskets would be a good idea, a new belt, water pump, hoses, radiator, would probably be a good time to throw a smaller pulley on the S/C. Hmmm......

One more question, would I HAVE to get a tune, or if I only go t say a 3.5 or 3.4 pulley, would the stock system be able to handle the new setup? I understand a tune would get the most out of the setup, but just curious if it is a must have?

**sseilmnop** · 02-12-2014

You should be able to drive it to get tuned but I wouldn't run it long turn with out a tune.

**sseilmnop** · 02-15-2014

Bump $425

**Regalgse00** · 02-20-2014

I might buy this in the next 2 weeks

**sseilmnop** · 02-23-2014

Bump

**SgtMarshal** · 02-23-2014

I dont think tuning is necessary to run an intercooler, and I think fuel injector spacers are cheaper than modified fuel rails but work just as good. good luck with the sell

**sseilmnop** · 02-23-2014

Originally Posted by johntremell

I dont think tuning is necessary to run an intercooler, and I think fuel injector spacers are cheaper than modified fuel rails but work just as good. good luck with the sell

Who makes 2-1/4" spacers?

**Scottydoggs** · 02-23-2014

ive seen injector spacers on a regal local to me. iirc the guy said he made them him self.

**sseilmnop** · 02-23-2014

Originally Posted by Scottydoggs

ive seen injector spacers on a regal local to me. iirc the guy said he made them him self.

Home made would be cheaper!

Tuning is not required but an intercooler lets you drop multiple pulley sizes and I recommend a tune!

**SgtMarshal** · 02-23-2014

Agreed

**sseilmnop** · 03-02-2014

Bump

**Kilroy** · 03-03-2014

Could the top of the fuel rails be cut, and appropriate flexible fuel line used to make it fit? I understand you would probably have to very carefully bend the lines so they go over the S/C instead of thru them.

Not sure I like the spacer idea, especially if they have to be 2 1/4" long!