Thread: Swapped to supercharged

Page 1 of 3 123 LastLast
Results 1 to 20 of 49
  1. #1 Swapped to supercharged 
    SE Level Member snutmeez's Avatar
    Join Date
    Dec 2014
    Location
    HALIFAX, NOVA SCOTIA
    Posts
    35
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    2
    So I just recently swapped from N/A to supercharged, put everything back the same way it came out, checked, re-checked and checked again and I must be missing something because it will not start at all. It cranks, starter works, got fuel pressure, got oil pressure, changed ICM, good grounds, battery new, alternator good. I used the coil pack from the N/A engine. Both engine ran before the swap and I also did the necessary wiring for the boost control valve/maf sensor extension. There are also no codes showing up on the scanner either. It really sounds like there is no spark. I need some help please
    Reply With Quote  
     

  2. #2 Re: Swapped to supercharged 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,995
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    Chats
    243824
    did you swap pcm's too. or is this a top swap?

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  3. #3 Re: Swapped to supercharged 
    SE Level Member snutmeez's Avatar
    Join Date
    Dec 2014
    Location
    HALIFAX, NOVA SCOTIA
    Posts
    35
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    2
    I did the whole swap, using the PCM too.
    Reply With Quote  
     

  4. #4 Re: Swapped to supercharged 
    SE Level Member snutmeez's Avatar
    Join Date
    Dec 2014
    Location
    HALIFAX, NOVA SCOTIA
    Posts
    35
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    2
    ​Yea I swapped PCM's
    Reply With Quote  
     

  5. #5 Re: Swapped to supercharged 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,995
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    Chats
    243824
    try a security learn, key to run for 10 minutes, then off for less then 10 seconds, back to run for 10 minutes, do this 3 times, then try to fire it up.

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  6. #6 Re: Swapped to supercharged 
    SE Level Member snutmeez's Avatar
    Join Date
    Dec 2014
    Location
    HALIFAX, NOVA SCOTIA
    Posts
    35
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    2
    Ok, I will try that, let ya know if it works. Thnx
    Reply With Quote  
     

  7. #7 Re: Swapped to supercharged 
    Turbo is the way to go. Fivefingerdeathpunch's Avatar
    Join Date
    Sep 2009
    Location
    Rogers, MN
    Posts
    21,030
    Thanks (Received)
    21
    Likes (Received)
    45
    Dislikes (Received)
    0
    Chats
    83662
    Anyone else having trouble reading the font?

    I can't see a damn thing about what he typed out.

    SMGPFC Member #1
    Reply With Quote  
     

  8. #8 Re: Swapped to supercharged 
    SE Level Member snutmeez's Avatar
    Join Date
    Dec 2014
    Location
    HALIFAX, NOVA SCOTIA
    Posts
    35
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    2
    The font is clear, you need it larger?
    Oh yea, Scotty, do I still do the security re-learn even if the security light goes right out after I turn the key to the on position?

    Reply With Quote  
     

  9. #9 Re: Swapped to supercharged 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,995
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    Chats
    243824
    i would. when you change pcm's 99% of the time the os dont match and you need to pair up the key to the pcm. takes 30 minutes, but its likely the cause.

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  10. Likes snutmeez liked this post
  11. #10 Re: Swapped to supercharged 
    SE Level Member snutmeez's Avatar
    Join Date
    Dec 2014
    Location
    HALIFAX, NOVA SCOTIA
    Posts
    35
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    2
    So I took the injectors off to do cleaning and guess what, yes they pulse after i tap the positive, but the spray,no spray, just a cpl drops and then nothing, just pulsing. I tried to clean them all and they all did the same thing. They're finished.....
    Reply With Quote  
     

  12. #11 Re: Swapped to supercharged 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,995
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    Chats
    243824
    you need some pressure behind them to make them spray. remember they got 45 psi of fuel pressure pushing the spray out.

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  13. #12 Re: Swapped to supercharged 
    SE Level Member snutmeez's Avatar
    Join Date
    Dec 2014
    Location
    HALIFAX, NOVA SCOTIA
    Posts
    35
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    2
    Ok, so how do I do it properly?
    Reply With Quote  
     

  14. #13 Re: Swapped to supercharged 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,995
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    Chats
    243824
    this is one way.


    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  15. #14 Re: Swapped to supercharged 
    GT Level Member brettstoner's Avatar
    Join Date
    Jul 2014
    Location
    Toledo, OH
    Posts
    263
    Thanks (Received)
    1
    Likes (Received)
    4
    Dislikes (Received)
    0
    Chats
    0
    When I accidentally reinstalled my 2 bar NA MAP sensor instead of the 3 bar SC sensor I got a no start condition. No codes, crank fine, but no fire. PCM turned off injectors. Swapped the MAP sensor to the 3 bar after I noticed it while troubleshooting and fired right up.... Food for thought....
    04 GP GT- top swap, VS cam, 2.8 pulley, E85, headers, 60 injectors, TEP 3:29 trans, Racelogic Traction Control, ZZP dyno tuned.
    Reply With Quote  
     

  16. #15 Re: Swapped to supercharged 
    SE Level Member snutmeez's Avatar
    Join Date
    Dec 2014
    Location
    HALIFAX, NOVA SCOTIA
    Posts
    35
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    2
    I did this exact method and they didn't spray, it just shot out once while i tapped the positive, my daughter sprayed full tilt and all it did was fill the hose with cleaner after the one shot. I did them all with the same results, re-checked, same result, nothing, just pulsing. That means they are cooked right?
    Reply With Quote  
     

  17. #16 Re: Swapped to supercharged 
    Killa Bee Scottydoggs's Avatar
    Join Date
    Aug 2010
    Location
    new jersey
    Posts
    39,995
    Thanks (Received)
    63
    Likes (Received)
    166
    Dislikes (Received)
    5
    Chats
    243824
    i find it hard to believe all 6 are fubared.

    98 Buick Regal GS, F body brakes, Caddy STS wheels, tinted tails L36 bottom end, lightly ported heads, 1.95 roller rockers, headers, gen 5 N* 3.0 pulley, FSIC, 42 lb injectors, a BrandonHall rebuilt trans, DHP tuned and AEM water/Meth injection https://goo.gl/gpV5kW
    Reply With Quote  
     

  18. Likes wowitsfast liked this post
  19. #17 Re: Swapped to supercharged 
    SE Level Member snutmeez's Avatar
    Join Date
    Dec 2014
    Location
    HALIFAX, NOVA SCOTIA
    Posts
    35
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    2
    ​Yeah, that is what I said as I tested them and they were failing.
    Reply With Quote  
     

  20. #18 Re: Swapped to supercharged 
    GTP Level Member wowitsfast's Avatar
    Join Date
    Oct 2014
    Location
    portland oregon
    Posts
    959
    Thanks (Received)
    6
    Likes (Received)
    34
    Dislikes (Received)
    0
    Chats
    507
    The video did say don't let it full spray because it would burn out the injector. It is designed to pulse rapidly.

    If you have a volt meter check em out I'm not sure what they are supposed to read but depending how long you full sprayed them they are probably burnt.

    At least they are affordable. Rock on rockauto

    Sent from my SM-N920V using Tapatalk
    Just a bunch of junk thrown together http://www.grandprixforums.com/membe...ht=wowitsfasts
    Reply With Quote  
     

  21. #19 Re: Swapped to supercharged 
    SE Level Member snutmeez's Avatar
    Join Date
    Dec 2014
    Location
    HALIFAX, NOVA SCOTIA
    Posts
    35
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    2
    No, I didn't just touch the positive to let it shoot out once. I tapped it to make it pulse and I only got one shot of fuel from the injectors. I already know they burn out if you just hold it to the positive.
    Reply With Quote  
     

  22. #20 Re: Swapped to supercharged 
    SE Level Member snutmeez's Avatar
    Join Date
    Dec 2014
    Location
    HALIFAX, NOVA SCOTIA
    Posts
    35
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    2
    My daughter was spraying the cleaner fully while I pulsed the injectors.
    Reply With Quote  
     

Page 1 of 3 123 LastLast

Similar Threads

  1. Replies: 4
    Last Post: 03-02-2019, 11:28 PM
  2. Replies: 7
    Last Post: 07-29-2017, 03:45 PM
  3. 98 GP GT L67 swapped needs pcm which one??
    By 98PONTIAC in forum General Tech Discussion
    Replies: 5
    Last Post: 12-27-2012, 03:14 PM
  4. Top swapped
    By Dragon1972 in forum PCM Tuning
    Replies: 5
    Last Post: 05-03-2012, 09:07 AM
  5. swap a series 2 supercharged motor for a series 3 supercharged into my 2000 gtp
    By 2000GTPGUY in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 3
    Last Post: 01-21-2012, 04:26 PM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •