Thread: 3.4 knock

Page 2 of 2 FirstFirst 12
Results 21 to 32 of 32
  1. #21 Re: 3.4 knock 
    SE Level Member
    Join Date
    Aug 2013
    Location
    mpls, mn
    Posts
    65
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    inspection cover on a fwd trans? i pulled a 4l60e last yr. i think it had one. but that is RWD. going to go look at the nox and see whats on the bottom of trans bell housing. you can force flex plate for/rev and possibly hear/feel a flexplate crack. or run motor and use stethoscope to listen to it. the part about using a screwdriver to check rod knock sounds good. since intake is off i can reach all plugs fairly well. ah, life is so much fun
    Reply With Quote  
     

  2. #22 Re: 3.4 knock 
    SE Level Member
    Join Date
    Aug 2013
    Location
    mpls, mn
    Posts
    65
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    Nox has af-33 trans. Not a 4t65-e. You remove starter to access flexplate bolts. There is no access plate that I am aware of. Next step?
    Reply With Quote  
     

  3. #23 Re: 3.4 knock 
    GTX Level Member wstefan20's Avatar
    Join Date
    Aug 2017
    Location
    Raytown, MO
    Posts
    1,153
    Thanks (Received)
    33
    Likes (Received)
    63
    Dislikes (Received)
    1
    Chats
    34
    Lol didn't know what you meant by "nox " at first! Lol and you're right. That stinks. Hm... I'd use the screwdriver check next then go ahead and do the lifters/ pushrods/ rocker swap.

    One other thought is to remove the oil filter and cut it apart. If you see any "glitter", run! You could also swap the oil plug with a magnetic one to see what sticks.

    Anything to avoid pulling the trans to check the flexplate! Haha
    Reply With Quote  
     

  4. #24 Re: 3.4 knock 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,833
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    Chats
    98246
    Yeah..it's possible to break a flex plate, especially if mounts are bad.

    From a guy that broke one and thought....it's either rod knock or a flex.. you can listen to it and or pull motor and check it. Easy enough to do. Just drain the coolant, lift up and presto.. Some are going to say it's not that easy, I think it is.. lol
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  5. #25 Re: 3.4 knock 
    GTX Level Member wstefan20's Avatar
    Join Date
    Aug 2017
    Location
    Raytown, MO
    Posts
    1,153
    Thanks (Received)
    33
    Likes (Received)
    63
    Dislikes (Received)
    1
    Chats
    34
    Quote Originally Posted by BillBoost37 View Post
    Yeah..it's possible to break a flex plate, especially if mounts are bad.

    From a guy that broke one and thought....it's either rod knock or a flex.. you can listen to it and or pull motor and check it. Easy enough to do. Just drain the coolant, lift up and presto.. Some are going to say it's not that easy, I think it is.. lol
    Lol Bill, you would say pulling a porche 991 is easy!

    Probably not much worse than a 3800 and those are easy. My only experience pulling one is my wife's Aztek, and you can't get it out the top with the heads on because of the dash. Grand prix 3.4s are probably not that bad.
    Reply With Quote  
     

  6. #26 Re: 3.4 knock 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,833
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    Chats
    98246
    I figure it's not much worse than a 3.8.

    You drop a jack under the passenger end of the trans, do the converter bolts, trans to engine bolts, drain the coolant, push the wiring to the side and lift. Honestly.. I did my regal so fast the wife asked me why I had the garage door open when I was trying to show her I drove the car back to this house......when 1.5 hours earlier I sent her a pic of the motor in the air. The woman expects too much from me now
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  7. #27 Re: 3.4 knock 
    GTX Level Member wstefan20's Avatar
    Join Date
    Aug 2017
    Location
    Raytown, MO
    Posts
    1,153
    Thanks (Received)
    33
    Likes (Received)
    63
    Dislikes (Received)
    1
    Chats
    34
    Quote Originally Posted by BillBoost37 View Post
    I figure it's not much worse than a 3.8.

    You drop a jack under the passenger end of the trans, do the converter bolts, trans to engine bolts, drain the coolant, push the wiring to the side and lift. Honestly.. I did my regal so fast the wife asked me why I had the garage door open when I was trying to show her I drove the car back to this house......when 1.5 hours earlier I sent her a pic of the motor in the air. The woman expects too much from me now
    Lol I know what you mean. Just don't try to drop the oil pan in the car. Took me the better part of a day because you can't really reach the cross bolts in between the engine and transmission, and you have to do a dance with the engine mount by dropping the subframe and lifting the engine enough to let the oil pan clear.
    Reply With Quote  
     

  8. #28 Re: 3.4 knock 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,833
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    Chats
    98246
    I do find that often the easier way to doing a pan is to drop the subframe out. a 4x4 and chain will hold the engine/trans up, undo your rack bolts, break the balljoints free and free the trans cooler/wiring, down it comes. And totally out of the way, vs trying to go around it.
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  9. #29 Re: 3.4 knock 
    SE Level Member
    Join Date
    Aug 2013
    Location
    mpls, mn
    Posts
    65
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    it is back together. replacing lifters is hard enough but you add the step of removing them from another rig and the job grows. i did get another egr tube as the original one had a big split in the bellows. and a dipstick tube as the welded on tab snapped off when i pulled the heads 2 weeks ago. now, add oil and water and see whats up.
    Reply With Quote  
     

  10. #30 Re: 3.4 knock 
    SE Level Member
    Join Date
    Aug 2013
    Location
    mpls, mn
    Posts
    65
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    It's fixed. Was it the dang 2 switched pushrods? I swapped out the rocker/lifters/pushrods from boneyard nox.
    Reply With Quote  
     

  11. #31 Re: 3.4 knock 
    Turbo is the way to go. BillBoost37's Avatar
    Join Date
    Jul 2009
    Location
    W Spfld
    Posts
    26,833
    Thanks (Received)
    53
    Likes (Received)
    90
    Dislikes (Received)
    1
    Chats
    98246
    Congrats...

    We can't tell you what caused it as we can only go on what you said. Maybe it was a lifter or two and then the flubbed pushrods came in when you put it back together. Smile and move forward.
    I drink..so consider that when reading my posts.

    2010 Audi A6 Dual IC's
    Reply With Quote  
     

  12. #32 Re: 3.4 knock 
    GTX Level Member wstefan20's Avatar
    Join Date
    Aug 2017
    Location
    Raytown, MO
    Posts
    1,153
    Thanks (Received)
    33
    Likes (Received)
    63
    Dislikes (Received)
    1
    Chats
    34
    Nice! Yeah, these cars are ultra picky about the pushrod order, and the lifters tend to get noisy when gummed up. Luckily you caught it before anything major happened!
    Reply With Quote  
     

Page 2 of 2 FirstFirst 12

Similar Threads

  1. help with knock?
    By natethegreat in forum PCM Tuning
    Replies: 15
    Last Post: 05-16-2014, 10:44 AM
  2. Rod Knock?
    By 87IROCZOWNER69 in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 14
    Last Post: 12-03-2013, 10:29 PM
  3. rod knock or something else?
    By mainjet in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 31
    Last Post: 10-08-2011, 09:46 PM
  4. Listen to the knock knock knock....
    By Lsick7 in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 18
    Last Post: 02-23-2011, 05:40 PM
  5. help with the knock please
    By BankRupt in forum 3.8L V6 Supercharged (L67)(L32)
    Replies: 12
    Last Post: 01-14-2010, 02:29 PM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •