Thread: 3.4 DOHC Torque Curve

Results 1 to 10 of 10
  1. #1 3.4 DOHC Torque Curve 
    SE Level Member
    Join Date
    Sep 2010
    Location
    Bettendorf, IA
    Posts
    94
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    Anyone have information on Torque curve on these engines? I'm looking at changing gear ratios, i want to make sure I try to optimize torque/hp so I don't under gear (poor performance) or over Gear it(worse gas mileage)
    Reply With Quote  
     

  2. #2 Re: 3.4 DOHC Torque Curve 
    Turbo is the way to go. Fivefingerdeathpunch's Avatar
    Join Date
    Sep 2009
    Location
    Rogers, MN
    Posts
    21,030
    Thanks (Received)
    21
    Likes (Received)
    45
    Dislikes (Received)
    0
    Chats
    83662
    How are you going to tune it for those changes?

    A good guess would say your powerband is 2500-5000ish rpm an faills off before it shifts. You should just leave it.

    SMGPFC Member #1
    Reply With Quote  
     

  3. #3 Re: 3.4 DOHC Torque Curve 
    GT Level Member 91gpse's Avatar
    Join Date
    Mar 2009
    Location
    warren, mi
    Posts
    153
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    135
    i would agree with five finger death punch... if you want to mess with gears your better off getting a manual trans. which its not worth it unless you got some serious mods in the engine.
    Reply With Quote  
     

  4. #4 Re: 3.4 DOHC Torque Curve 
    GXP Level Member ctracer's Avatar
    Join Date
    Sep 2010
    Location
    new britain, ct
    Posts
    2,295
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    38971
    since this thread got bumped....these 3.4 dohc engines make good use of the upper powerband.
    a guy on here had 3.69's? i think? and he absolutely loved them with this engine.
    07 Black GXP.
    Reply With Quote  
     

  5. #5 Re: 3.4 DOHC Torque Curve 
    SE Level Member
    Join Date
    Sep 2010
    Location
    Bettendorf, IA
    Posts
    94
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    3.69? Came with factory 3:43. Wonder how he got to 3:69?
    Reply With Quote  
     

  6. #6 Re: 3.4 DOHC Torque Curve 
    GT Level Member
    Join Date
    Dec 2013
    Location
    laporte mn
    Posts
    316
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    U get 3.69 by using a final drive from a 3100 v6 car with a 4t60e. And he also used a 245/45r17 tire and ended up with a ratio of 3.73. The guy I know that has done it is z34phoenix. He is on wbody forum a lot. I also have done the diff swap to 3.69 but my car isn't driving until the snow clears so I don't have any opinion on it

    Sent from my MB886 using Tapatalk
    Reply With Quote  
     

  7. #7 Re: 3.4 DOHC Torque Curve 
    Florida Tuner Z34Phoenix's Avatar
    Join Date
    Mar 2011
    Location
    Florida
    Posts
    873
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    292
    no actually when you install the 3100 final drive you end up with 3.73's using my 245/45-17 tires the final drive would be equivalent to 4.09

    96 Z34 (RIP LQ1 14.81@92.3) L36 Swap 14.9@91.5 www.cardomain.com/id/z34phoenix
    Topswap: P&P All,Si Valves,L76's,LW Pushrods,SD's,DHP PT PB 13.91@99.8
    Reply With Quote  
     

  8. #8 Re: 3.4 DOHC Torque Curve 
    SE Level Member padgett's Avatar
    Join Date
    Feb 2016
    Location
    Orlando
    Posts
    12
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    My SPI includes FV0 RATIO, TRANSAXLE FINAL DRIVE 3.67
    Reply With Quote  
     

  9. #9 Re: 3.4 DOHC Torque Curve 
    SE Level Member
    Join Date
    Sep 2010
    Location
    Bettendorf, IA
    Posts
    94
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    0
    3:69? Wow, and I thought I loved the 3:43. Reprogramissues?
    Reply With Quote  
     

  10. #10 Re: 3.4 DOHC Torque Curve 
    Florida Tuner Z34Phoenix's Avatar
    Join Date
    Mar 2011
    Location
    Florida
    Posts
    873
    Thanks (Received)
    0
    Likes (Received)
    0
    Dislikes (Received)
    0
    Chats
    292
    Just used a DHP power tuner and then remapped the shift points. Needed a special release of the dhp software. The latest release doesn't have the settings needed for the 96 z34
    Reply With Quote  
     

Similar Threads

  1. 3.4 dohc
    By 67GTO in forum General Tech Discussion
    Replies: 1
    Last Post: 06-11-2010, 06:36 AM
  2. Engine swap - 96' 3.4l DOHC out, '93 3.4l DOHC
    By csbrown in forum 3.4L V6 (LQ1) DOHC
    Replies: 1
    Last Post: 11-11-2009, 04:47 PM
  3. Replies: 12
    Last Post: 02-08-2009, 01:06 AM
Tags for this Thread

View Tag Cloud

Bookmarks
Bookmarks
Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •